SoC variants. Fold the AT91SAM9XE chips into the AT91SAM9260
handling, where appropriate. The following SoCs/SoC families are recognized:
at91cap9, at91rm9200, at91sam9260, at91sam9261, at91sam9263,
at91sam9g10, at91sam9g20, at91sam9g45, at91sam9n12, at91sam9rl,
at91sam9x5
and the following variations are also recognized:
at91rm9200_bga, at91rm9200_pqfp, at91sam9xe, at91sam9g45, at91sam9m10,
at91sam9g46, at91sam9m11, at91sam9g15, at91sam9g25, at91sam9g35,
at91sam9x25, at91sam9x35
This is only the identification routine: no additional Atmel devices
are supported at this time.
# With these changes, I'm able to boot to the point of identification
# on a few different Atmel SoCs that we don't yet support using the
# KB920X config file -- someday tht will be an ATMEL config file...
structure with the first 4 registers to allow a wider range of boot
loaders to work. Future commits will make use of this to centralize
support for the different loaders.
- Move DMA tag and map creature to at91_spi_activate() where the other
resource allocation also lives. [1]
- Flesh out at91_spi_deactivate(). [1]
- Work around the "Software Reset must be Written Twice" erratum.
- For now, run the bus at the slowest speed possible in order to work
around data corruption on transit even seen with 9 MHz on ETHERNUT5
(15 MHz maximum) and AT45DB321D (20 MHz maximum). This also serves as
a poor man's work-around for the "NPCSx rises if no data data is to be
transmitted" erratum of RM9200. Being able to use the appropriate bus
speed would require:
1) Adding a proper work-around for the RM9200 bug consisting of taking
the chip select control away from the SPI peripheral and managing it
directly as a GPIO line.
2) Taking the maximum frequencies supported by the actual board and the
slave devices into account and basing the whole thing on the master
clock instead of hardcoding a divisor as previously done.
3) Fixing the above mentioned data corruption.
- KASSERT that TX/RX command and data sizes match on transfers.
- Introduce a mutex ensuring that only one child device is running a SPI
transfer at a time. [1]
- Add preliminary, #ifdef'ed out support for setting the chip select. [1]
- Use the RX instead of the TX commando size when setting up the RX side
of a transfer.
- For controllers having SPI_SR_TXEMPTY, i.e. !RM9200, also wait for the
completion of the TX part of transfers before stopping the whole thing
again.
- Use DEVMETHOD_END. [1]
- Use NULL instead of 0 for pointers. [1, partially]
Additional testing by: Ian Lepore
Submitted by: Ian Lepore [1]
MFC after: 1 week
console so initialized will work upon return from cninit. While this
is the very next line, other platforms setup all this stuff before
calling cninit. Also, initialize the SDRAM base register in the inner
block in at91_ramsize().
compiled into the kernel. This allows us to boot the same kernel on
machines with different master clock frequencies, so long as we can
determine the main clock frequency accurately. Cleanup the pmc clock
init function so it can be called in early boot so we can use the
serial port just after we call cninit.
# We have two calls to at91_pmc_clock_init for reasons unknown, that will
# be fixed later -- it is harmless for now.
DataFlash.
- Add a mapping for the Nut/OS configuration DataFlash partition according
to the board manual (but not known to either Linux or U-Boot (patches).
in_cksum.h required ip.h to be included for struct ip. To be
able to use some general checksum functions like in_addword()
in a non-IPv4 context, limit the (also exported to user space)
IPv4 specific functions to the times, when the ip.h header is
present and IPVERSION is defined (to 4).
We should consider more general checksum (updating) functions
to also allow easier incremental checksum updates in the L3/4
stack and firewalls, as well as ponder further requirements by
certain NIC drivers needing slightly different pseudo values
in offloading cases. Thinking in terms of a better "library".
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
Reviewed by: gnn (as part of the whole)
MFC After: 3 days
frequency in the at91_pmc_clock_init rather than passing it in. Allow
for frequencies >= 21MHz by rounding to the nearest 500Hz (Idea from
Ian Lapore whose company uses a similar arrangement in their product).
at91_pmc_clock_init() is now nearly independent of the rest of the pmc
driver (which means we may be able to call it much earlier in boot
soon to eliminate the master clock config file requirement for printf
to work during early boot and also eliminate some interdependencies
with the device ordering which requires pmc to be the first device
added).
all integrated and on-board peripherals except the DataFlash (at91_spi(4)
and at45d(4) still need to be unb0rken) and NAND Flash (missing NAND
framework) are working.
AFAICT, this makes FreeBSD the first operating system besides Nut/OS
supporting Ethernut 5 out of tree.
ports. This currently is a nop, but will soon be used to allow
support for multiple boards to be built into one kernel (starting with
AT91RM9200 and expanding out from there).
- Align the RX buffers on the cache line size, otherwise the requirement
of partial cache line flushes on every are pretty much guaranteed. [1]
- Make the code setting the RX timeout match its comment (apparently,
start and stop bits were missed in the previous calculation). [1]
- Cover the busdma operations in at91_usart_bus_{ipend,transmit}() with
the hardware mutex, too, so these don't race against each other.
- In at91_usart_bus_ipend(), reduce duplication in the code dealing with
TX interrupts.
- In at91_usart_bus_ipend(), turn the code dealing with RX interrupts
into an else-if cascade in order reduce its complexity and to improve
its run-time behavior.
- In at91_usart_bus_ipend(), add missing BUS_DMASYNC_PREREAD calls on
the RX buffer map before handing things over to the hardware again. [1]
- In at91_usart_bus_getsig(), used a variable of sufficient width for
storing the contents of USART_CSR.
- Use KOBJMETHOD_END.
- Remove an unused header.
Submitted by: Ian Lepore [1]
Reviewed by: Ian Lepore
MFC after: 1 week
as otherwise the interrupt handling code may modify data in the non-DMA
part of the cache line while we have it stashed away in the temporary
stack buffer, then we end up restoring a stale value.
PR: 160431
Submitted by: Ian Lepore
MFC after: 1 week
