to profile outoing packets for a number of mbuf chain
related parameters
e.g. number of mbufs, wasted space.
probably will do with further work later.
Reviewed by: various
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
(ECMP) for both IPv4 and IPv6. Previously, multipath route insertion
is disallowed. For example,
route add -net 192.103.54.0/24 10.9.44.1
route add -net 192.103.54.0/24 10.9.44.2
The second route insertion will trigger an error message of
"add net 192.103.54.0/24: gateway 10.2.5.2: route already in table"
Multiple default routes can also be inserted. Here is the netstat
output:
default 10.2.5.1 UGS 0 3074 bge0 =>
default 10.2.5.2 UGS 0 0 bge0
When multipath routes exist, the "route delete" command requires
a specific gateway to be specified or else an error message would
be displayed. For example,
route delete default
would fail and trigger the following error message:
"route: writing to routing socket: No such process"
"delete net default: not in table"
On the other hand,
route delete default 10.2.5.2
would be successful: "delete net default: gateway 10.2.5.2"
One does not have to specify a gateway if there is only a single
route for a particular destination.
I need to perform more testings on address aliases and multiple
interfaces that have the same IP prefixes. This patch as it
stands today is not yet ready for prime time. Therefore, the ECMP
code fragments are fully guarded by the RADIX_MPATH macro.
Include the "options RADIX_MPATH" in the kernel configuration
to enable this feature.
Reviewed by: robert, sam, gnn, julian, kmacy
user-mode lock manager, build a kernel with the NFSLOCKD option and
add '-k' to 'rpc_lockd_flags' in rc.conf.
Highlights include:
* Thread-safe kernel RPC client - many threads can use the same RPC
client handle safely with replies being de-multiplexed at the socket
upcall (typically driven directly by the NIC interrupt) and handed
off to whichever thread matches the reply. For UDP sockets, many RPC
clients can share the same socket. This allows the use of a single
privileged UDP port number to talk to an arbitrary number of remote
hosts.
* Single-threaded kernel RPC server. Adding support for multi-threaded
server would be relatively straightforward and would follow
approximately the Solaris KPI. A single thread should be sufficient
for the NLM since it should rarely block in normal operation.
* Kernel mode NLM server supporting cancel requests and granted
callbacks. I've tested the NLM server reasonably extensively - it
passes both my own tests and the NFS Connectathon locking tests
running on Solaris, Mac OS X and Ubuntu Linux.
* Userland NLM client supported. While the NLM server doesn't have
support for the local NFS client's locking needs, it does have to
field async replies and granted callbacks from remote NLMs that the
local client has contacted. We relay these replies to the userland
rpc.lockd over a local domain RPC socket.
* Robust deadlock detection for the local lock manager. In particular
it will detect deadlocks caused by a lock request that covers more
than one blocking request. As required by the NLM protocol, all
deadlock detection happens synchronously - a user is guaranteed that
if a lock request isn't rejected immediately, the lock will
eventually be granted. The old system allowed for a 'deferred
deadlock' condition where a blocked lock request could wake up and
find that some other deadlock-causing lock owner had beaten them to
the lock.
* Since both local and remote locks are managed by the same kernel
locking code, local and remote processes can safely use file locks
for mutual exclusion. Local processes have no fairness advantage
compared to remote processes when contending to lock a region that
has just been unlocked - the local lock manager enforces a strict
first-come first-served model for both local and remote lockers.
Sponsored by: Isilon Systems
PR: 95247 107555 115524 116679
MFC after: 2 weeks
While the KSE project was quite successful in bringing threading to
FreeBSD, the M:N approach taken by the kse library was never developed
to its full potential. Backwards compatibility will be provided via
libmap.conf for dynamically linked binaries and static binaries will
be broken.
not have VTOC information about the partitions, it will be created.
This is because the VTOC information is used for the partition type
and FreeBSD's sunlabel(8) does not create nor use VTOC information.
For this purpose, new tags have been added to support FreeBSD's
partition types.
overridden at compile-time using kernel options of the same names.
Rather than doing a compile-time CTASSERT of buffer sizes being
even multiples of block sizes, just adjust them at boottime, as
the failure mode is more user-friendly.
MFC after: 2 months
PR: 119993
Suggested by: Scot Hetzel <swhetzel at gmail dot com>
the ABI when enabled. There is no longer an embedded lock_profile_object
in each lock. Instead a list of lock_profile_objects is kept per-thread
for each lock it may own. The cnt_hold statistic is now always 0 to
facilitate this.
- Support shared locking by tracking individual lock instances and
statistics in the per-thread per-instance lock_profile_object.
- Make the lock profiling hash table a per-cpu singly linked list with a
per-cpu static lock_prof allocator. This removes the need for an array
of spinlocks and reduces cache contention between cores.
- Use a seperate hash for spinlocks and other locks so that only a
critical_enter() is required and not a spinlock_enter() to modify the
per-cpu tables.
- Count time spent spinning in the lock statistics.
- Remove the LOCK_PROFILE_SHARED option as it is always supported now.
- Specifically drop and release the scheduler locks in both schedulers
since we track owners now.
In collaboration with: Kip Macy
Sponsored by: Nokia
o Disklabels can have between 8 and 20 partitions (inclusive).
o No device special file is created for the raw partition.
o Switch ia64 to use this backend.
o No support for boot code yet.
- Introduce per-architecture stack_machdep.c to hold stack_save(9).
- Introduce per-architecture machine/stack.h to capture any common
definitions required between db_trace.c and stack_machdep.c.
- Add new kernel option "options STACK"; we will build in stack(9) if it is
defined, or also if "options DDB" is defined to provide compatibility
with existing users of stack(9).
Add new stack_save_td(9) function, which allows the capture of a stacktrace
of another thread rather than the current thread, which the existing
stack_save(9) was limited to. It requires that the thread be neither
swapped out nor running, which is the responsibility of the consumer to
enforce.
Update stack(9) man page.
Build tested: amd64, arm, i386, ia64, powerpc, sparc64, sun4v
Runtime tested: amd64 (rwatson), arm (cognet), i386 (rwatson)
Currently, Giant is not too much contented so that it is ok to treact it
like any other mutexes.
Please don't forget to update your own custom config kernel files.
Approved by: cognet, marcel (maintainers of arches where option is
not enabled at the moment)
providers with limited physical storage and add physical storage as
needed.
Submitted by: Ivan Voras
Sponsored by: Google Summer of Code 2006
Approved by: re (kensmith)
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
previously conditionally acquired Giant based on debug.mpsafenet. As that
has now been removed, they are no longer required. Removing them
significantly simplifies error-handling in the socket layer, eliminated
quite a bit of unwinding of locking in error cases.
While here clean up the now unneeded opt_net.h, which previously was used
for the NET_WITH_GIANT kernel option. Clean up some related gotos for
consistency.
Reviewed by: bz, csjp
Tested by: kris
Approved by: re (kensmith)
Also rename the related functions in a similar way.
There are no functional changes.
For a packet coming in with IPsec tunnel mode, the default is
to only call into the firewall with the "outer" IP header and
payload.
With this option turned on, in addition to the "outer" parts,
the "inner" IP header and payload are passed to the
firewall too when going through ip_input() the second time.
The option was never only related to a gif(4) tunnel within
an IPsec tunnel and thus the name was very misleading.
Discussed at: BSDCan 2007
Best new name suggested by: rwatson
Reviewed by: rwatson
Approved by: re (bmah)
included man pages on how to use it. This code is still somewhat experimental
but has been successfully tested on a number of targets. Many thanks to
Danny for contributing this.
Approved by: re
NET_NEEDS_GIANT, which will shortly be removed. This is done in a
away that it may be easily reattached to the build before 7.1 if
appropriate locking is added. Specifics:
- Don't install netatm include files
- Disconnect netatm command line management tools
- Don't build libatm
- Don't include ATM parts in rescue or sysinstall
- Don't install sample configuration files and documents
- Don't build kernel support as a module or in NOTES
- Don't build netgraph wrapper nodes for netatm
This removes the last remaining consumer of NET_NEEDS_GIANT.
Reviewed by: harti
Discussed with: bz, bms
Approved by: re (kensmith)
- CMT_PF states added (w/sysctl to turn the PF version on)
- sctp_input.c had a missing incr of cookie case when the
auth was bad. This meant a free was called without an
increment to refcnt, added increment like rest of code.
- There was a case, unlikely, when the scope of the destination
changed (this is a TSNH case). In that case, it would not free
the alloc'ed asoc (in sctp_input.c).
- When listed addresses found a colliding cookie/Init, then
the collided upon tcb was not unlocked in sctp_pcb.c
- Add error checking on arguments of sctp_sendx(3) to prevent it from
referencing a NULL pointer.
- Fix an error return of sctp_sendx(3), it was returing
ENOMEM not -1.
- Get assoc id was changed to use the sanctified socket api
method for getting a assoc id (PEER_ADDR_INFO instead of
PEER_ADDR_PARAMS).
- Fix it so a peeled off socket will get a proper error return
if it trys to send to a different address then it is connected to.
- Fix so that select_a_stream can avoid an endless loop that
could hang a caller.
- time_entered (state set time) was not being set in all cases
to the time we went established.
Approved by: re(ken smith)
- Adjust lock_profiling stubs semantic in the hard functions in order to be
more accurate and trustable
- Disable shared paths for lock_profiling. Actually, lock_profiling has a
subtle race which makes results caming from shared paths not completely
trustable. A macro stub (LOCK_PROFILING_SHARED) can be actually used for
re-enabling this paths, but is currently intended for developing use only.
- Use homogeneous names for automatic variables in hard functions regarding
lock_profiling
- Style fixes
- Add a CTASSERT for some flags building
Discussed with: kmacy, kris
Approved by: jeff (mentor)
Approved by: re
the 7.0 timeframe.
This is needed because I4B is not locked and NET_NEEDS_GIANT goes away.
The plan is to lock I4B and bring everything back for 7.1.
Approved by: re (kensmith)
This allocator uses a binary buddy system with a twist. First and
foremost, this allocator is required to support the implementation of
superpages. As a side effect, it enables a more robust implementation
of contigmalloc(9). Moreover, this reimplementation of
contigmalloc(9) eliminates the acquisition of Giant by
contigmalloc(..., M_NOWAIT, ...).
The twist is that this allocator tries to reduce the number of TLB
misses incurred by accesses through a direct map to small, UMA-managed
objects and page table pages. Roughly speaking, the physical pages
that are allocated for such purposes are clustered together in the
physical address space. The performance benefits vary. In the most
extreme case, a uniprocessor kernel running on an Opteron, I measured
an 18% reduction in system time during a buildworld.
This allocator does not implement page coloring. The reason is that
superpages have much the same effect. The contiguous physical memory
allocation necessary for a superpage is inherently colored.
Finally, the one caveat is that this allocator does not effectively
support prezeroed pages. I hope this is temporary. On i386, this is
a slight pessimization. However, on amd64, the beneficial effects of
the direct-map optimization outweigh the ill effects. I speculate
that this is true in general of machines with a direct map.
Approved by: re
Please note that, this is currently considered as an
experimental feature so there could be some rough
edges. Consult http://wiki.freebsd.org/TMPFS for
more information.
For now, connect tmpfs to build on i386 and amd64
architectures only. Please let us know if you have
success with other platforms.
This work was developed by Julio M. Merino Vidal
for NetBSD as a SoC project; Rohit Jalan ported it
from NetBSD to FreeBSD. Howard Su and Glen Leeder
are worked on it to continue this effort.
Obtained from: NetBSD via p4
Submitted by: Howard Su (with some minor changes)
Approved by: re (kensmith)
- Fix so VRF's will clean themselves up when no references are around.
- Allow sctp_ifa to be passed into inpcb_bind, addr_mgmt_ep_sa to bypass
normal validation checks.
- turn auto-asconf off for subset bound sockets
- Moves all logging to use KTR. This gets rid of most
of the logging #ifdef's with a few exceptions reducing
the number of config options for SCTP.
tunnels, and was not MPSAFE. The code can be easily restored in the
event that someone with an IPX over IP tunnel configuration can work
with me to test patches.
This removes one of five remaining consumers of NET_NEEDS_GIANT.
Approved by: re (kensmith)
is expanded, size of expansion was not taken int consideration.
- Fix so vtag hash is 1 bigger so that it modulo's out
correctly, avoids a panic when restart with right modulo happens.
- do not dereference stcb when control->do_not_ref_stcb is set
- Fix up packet logging to not often use a lock and also to
add to options.
- Fix some logging option duplication in the sctputil.h
The entire code is wrapperd in #ifdef ... #endif so it won't harm
the actual implementation, but developers are encouraged to test it.
For arm, ia64, ppc, sparc64 and sun4v some work is still
needed, thus arch maintainers are encouraged to bring their arch on par
with respect to i386 and amd64.
Approved by: re (implicit?)
obtaining and releasing shared and exclusive locks. The algorithms for
manipulating the lock cookie are very similar to that rwlocks. This patch
also adds support for exclusive locks using the same algorithm as mutexes.
A new sx_init_flags() function has been added so that optional flags can be
specified to alter a given locks behavior. The flags include SX_DUPOK,
SX_NOWITNESS, SX_NOPROFILE, and SX_QUITE which are all identical in nature
to the similar flags for mutexes.
Adaptive spinning on select locks may be enabled by enabling the
ADAPTIVE_SX kernel option. Only locks initialized with the SX_ADAPTIVESPIN
flag via sx_init_flags() will adaptively spin.
The common cases for sx_slock(), sx_sunlock(), sx_xlock(), and sx_xunlock()
are now performed inline in non-debug kernels. As a result, <sys/sx.h> now
requires <sys/lock.h> to be included prior to <sys/sx.h>.
The new kernel option SX_NOINLINE can be used to disable the aforementioned
inlining in non-debug kernels.
The size of struct sx has changed, so the kernel ABI is probably greatly
disturbed.
MFC after: 1 month
Submitted by: attilio
Tested by: kris, pjd
