This time, abandon the use of busdma and start interacting with the VM
system directly. Make use of the new kmem_alloc_attr() which allows us
to easily allocate non-contiguous pages to back the GART table. This
should help a lot when starting or restarting X after the system has
been running for a while and memory has become fragmented.
MFC after: 2 weeks
* On 32 bit platforms we steal the upper 4 bits of the map handle
to store a unique map id.
* On 64 bit platforms we steal the upper 24 bits.
Resolves issues where the offsets that are handed to mmap may overlap the VRAM on some cards.
Tested on: radeon, intel, mga, and via.
This will break nouveau. I will spin new patches shortly.
proper device_t so it faked the devctl event to appear like one, this is now a
notify which allows more information to be passed.
We notify for both the device attach/detach and for each usb interface. A devd
rule can now match on the interface properties, including composite devices
which may have a uvideo interface and also usound and possibly uhid too.
An example to match a umass device with a scsi subclass and BBB protocol would be
notify 100 {
match "system" "USB";
match "subsystem" "INTERFACE";
match "type" "ATTACH";
match "intclass" "0x08";
match "intsubclass" "0x06";
match "intprotocol" "0x50";
action ...
};
The old attach devctl event has been retained for the moment to make merging to
8.1 easier. This was never compatible with 7.x or earlier due to the ugen regex
change needed.
Reviewed by: warner
MFC after: 1 week
occurs. In addition, the delay when programming the short cable fix
should be 100us, not 100ms.
PR: kern/64556
Submitted by: Thomas Hurst <tom at hur.st>
Approved by: rrs (mentor)
MFC after: 1 week
no flowid is present, this was causing some bad
reordering, now just use 0.
Also, add a few watchdog bits, and tx handler bits
that were corrected in igb.
- Re-probe xfp / sfp+ socket on link events, in case user
has changed transceiver
- correctly report current media to avoid confusing lagg (reported by Panasas)
- Report link speed (submitted by yongari)
Reviewed by: yongari (earlier version)
MFC after: 7 days
This driver was written by Alexander Pohoyda and greatly enhanced
by Nikolay Denev. I don't have these hardwares but this driver was
tested by Nikolay Denev and xclin.
Because SiS didn't release data sheet for this controller, programming
information came from Linux driver and OpenSolaris. Unlike other open
source driver for SiS190/191, sge(4) takes full advantage of TX/RX
checksum offloading and does not require additional copy operation in
RX handler.
The controller seems to have advanced offloading features like VLAN
hardware tag insertion/stripping, TCP segmentation offload(TSO) as
well as jumbo frame support but these features are not available
yet. Special thanks to xclin <xclin<> cs dot nctu dot edu dot tw>
who sent fix for receiving VLAN oversized frames.
unneeded for legacy hardware.
Also remove some TSO related cruft.
Add some watchdog_time setting that was missing, thanks
to Mikolaj Golub for pointing that out.
* WPA-None requires ap_scan=2:
The major difference between ap_scan=1 (default) and 2 is, that no
IEEE80211_IOC_SCAN* ioctls/functions are called, though, there is a
dependency on those. For example the call to wpa_driver_bsd_scan()
sets the interface UP, this never happens, therefore the interface
must be marked up in wpa_driver_bsd_associate(). IEEE80211_IOC_SSID
also is not called, which means that the SSID has not been set prior
to the IEEE80211_MLME_ASSOC call.
* WPA-None has no support for sequence number updates, it doesn't make
sense to check for replay violations..
* I had some crashes right after the switch to RUN state, issue is
that sc->sc_lastrs was not yet defined.
Approved by: rpaulo (mentor)
MFC after: 3 weeks
StarCat systems which provides time-of-day services for both as well as
console service for Serengeti, i.e. Sun Fire V1280. While the latter is
described with a device type of serial in the OFW device tree, it isn't
actually an UART. Nevertheless the console service is handled by uart(4)
as this allowed to re-use quite a bit of MD and MI code. Actually, this
idea is stolen from Linux which interfaces the sun4v hypervisor console
with the Linux counterpart of uart(4).
set, it make sense to actually initialize that array. This fixes some
issues with 4965 adapters where the TX power is crucial.
This got lost somewhere while merging with the OpenBSD code.
Approved by: rpaulo (mentor)
Obtained from: OpenBSD
MFC after: 2 weeks
* Enable DC calibration and crystal calibration on Centrino Advanced-N
6250 parts.
* Workaround for a HW bug (does not affect 4965AGN) that may sporadically
affect latency under some rare circumstances. From a similar commit to
iwlwifi.
* Update sensitivity settings for 5000 series to workaround a performance
bug in the DSP (1000 is not affected so we keep the old values for 5000).
* Update sensitivity settings for 6000 series.
* Set differential gains on 6250 too (but use a 1.0 factor, not 1.5).
* Init OFDM sensitivity with min value (which depends on the chip)
instead of hardcoding it to 90.
* Read calibration version from ROM and set IWN_GP_DRIVER_CALIB_VER6
bit on 6x50 if version >= 6.
Approved by: rpaulo (mentor)
Obtained from: OpenBSD
MFC after: 2 weeks
- code flow in handler could let interrupt be
reenabled when not wanted.
- change where the RX lock is taken to improve
performance.
- adapter->msix is true for MSI systems also,
it needs to explicitly test for 82574, good one :)
