pipes, since open pipes are linked off a usbd_interface structure
that is free()'d when the configuration index is changed. Attempting
to close or use such pipes later would access freed memory and
usually crash the system.
The only driver that is known to trigger this problem is if_axe,
which is itself at fault, but it is worth detecting the situation
to avoid the obscure crashes that result from this type of easily
made driver mistakes.
behaviour lost in the change from 4.x style netgraph tee nodes.
Alter the tee node to use the new method. Document the behaviour.
Step the ABI version number... old netgraph klds will refuse to load.
Better than just crashing.
Submitted by: Gleb Smirnoff <glebius@cell.sick.ru>
make the key name matching case-insensitive. There are some drivers
and .inf files that have mismatched cases, e.g. the driver will look
for "AdhocBand" whereas the .inf file specifies a registry key to be
created called "AdHocBand." The mismatch is probably a typo that went
undetected (so much for QA), but since Windows seems to be case-insensitive,
we should be too.
In if_ndis.c, initialize rates and channels correctly so that specify
frequences correctly when trying to set channels in the 5Ghz band, and
so that 802.11b rates show up for some a/b/g cards (which otherwise
appear to have no 802.11b modes).
Also, when setting OID_802_11_CONFIGURATION in ndis_80211_setstate(),
provide default values for the beacon interval, ATIM window and dwelltime.
The Atheros "Aries" driver will crash if you try to select ad-hoc mode
and leave the beacon interval set to 0: it blindly uses this value and
does a division by 0 in the interrupt handler, causing an integer
divide trap.
of this micro-optimization occurs when we call pmap_enter() to wire an
already mapped page. Because of the micro-optimization, we fail to
mark the PTE as wired. Later, on teardown of the address space,
pmap_remove_pages() destroys the PTE before vm_fault_unwire() has
unwired the page. (pmap_remove_pages() is not supposed to destroy
wired PTEs. They are destroyed by a later call to pmap_remove().)
Thus, the page becomes lost.
Note: The page is not lost if the application called munlock(2), only
if it relies on teardown of the address space to unwire its pages.
For the historically inclined, this bug was introduced by a
megacommit, revision 1.182, roughly six years ago.
Leak observed by: green@ and dillon independently
Patch submitted by: dillon at backplane dot com
Reviewed by: tegge@
MFC after: 1 week
correct. Instead, check it against the possible settings (_PRS) when
the link is probed. This is important when using APIC mode but link
devices still have PIC mode settings. This is also what Linux does.
Additional prodding by: Len Brown len dot brown at intel dot com
based on the destination sleep state. Add a method to restore the old
state on resume. This is needed for the case of suspending to a very low
state disabling a GPE (i.e. S4), resuming, and then suspending to a higher
state (i.e. S3). This case should now keep the proper GPEs enabled.
device can wake the system. For example:
dev.root0.nexus0.acpi0.acpi_lid0.wake: 1
dev.root0.nexus0.acpi0.acpi_button0.wake: 1
dev.root0.nexus0.acpi0.pcib0.wake: 0
dev.root0.nexus0.acpi0.sio0.wake: 0
been developed for use with FreeBSD, version 4.8 and later.
Submitted by: Hema Joyce
Reviewed by: Prafulla Deuskar
Approved by: Prafulla Deuskar
MFC after: 1 week
subsystem lock to avoid tripping over an assertion regarding whether
the lock is held or not. This is likely to be the cause of a panic
tripped over by Andrea Campi.
acpi_wake_init:
Evaluate _PRW and set the GPE type
acpi_wake_set_enable:
Enable or disable a device's GPE.
acpi_wake_sleep_prep:
Perform any last-minute changes to the device to prepare it for
entering the given sleep state.
Also, walk the entire namespace when transitioning to a sleep state,
disabling any GPEs which aren't appropriate for the given state. Transition
acpi_lid and acpi_button to the new API.
This clears the way for non-ACPI-aware devices to wake the system (i.e.
modems) and fixes a problem where systems power up after shutdown when a
GPE is triggered.
In particular, disabling it was likely to break configurations
involving ng_vlan(4) since the latter couldn't control
the parent's VLAN_MTU in the way vlan(4) did.
Pointed out by: ru
does not reliably prevent the triggering of interrupts for all supported
configurations. Thus, the FIFO size probe could cause an interrupt,
which could lead to an interrupt storm in the shared interrupt case.
To prevent this, change ns8250_bus_probe() to use the overflow bit in
the line status register instead of the RX ready bit in the interrupt
identification register to detect whether the FIFO has filled up.
This allows us to clear all bits in the interrupt enable register during
the probe, which should prevent interrupts reliably.
Additionally, the detected FIFO size may be a bit more accurate, because
the overflow bit is only set when the FIFO did actually fill up, while
interrupts would trigger a bit early.
Reviewed and tested on a lot of hardware by: marcel
