I'm not too happy about the result either, but at least it has less
chance of backfiring.
This particular feature could be called "a mess" without offending
anybody.
Virtualize bdevsw[] from cdevsw. bdevsw() is now an (inline)
function.
Join CDEV_MODULE and BDEV_MODULE to DEV_MODULE (please pay attention
to the order of the cmaj/bmaj arguments!)
Join CDEV_DRIVER_MODULE and BDEV_DRIVER_MODULE to DEV_DRIVER_MODULE
(ditto!)
(Next step will be to convert all bdev dev_t's to cdev dev_t's
before they get to do any damage^H^H^H^H^H^Hwork in the kernel.)
Mark the GDB port in the config file with flags 0x80. Currently
only the sio driver checks these flags and sets up a GDB port,
but adding similar code to other serial drivers would be easy.
For backward compatibility, if an sio port is marked as the console
and no port is marked as the gdb port, the GDB port will be mapped
to the console port. This hack should go away at some point.
1:
s/suser/suser_xxx/
2:
Add new function: suser(struct proc *), prototyped in <sys/proc.h>.
3:
s/suser_xxx(\([a-zA-Z0-9_]*\)->p_ucred, \&\1->p_acflag)/suser(\1)/
The remaining suser_xxx() calls will be scrutinized and dealt with
later.
There may be some unneeded #include <sys/cred.h>, but they are left
as an exercise for Bruce.
More changes to the suser() API will come along with the "jail" code.
Interrupts under the new scheme are managed by the i386 nexus with the
awareness of the resource manager. There is further room for optimizing
the interfaces still. All the users of register_intr()/intr_create()
should be gone, with the exception of pcic and i386/isa/clock.c.
- fix cut/paste problem. :-)
- don't forget to call isa_dmacascade()
- reset the port after we release resources.
That last one is a trap to watch out for.. The isa bus driver uses the
same port/irq/mem/etc variables for the initial probe hints as it does
for allocation/deallocation tracking. Releasing a resource clears the
variable and then you loose the hint during attach.. (ouch!)
had a quirk that made a shim rather hard to implement properly and it was
just easier to convert the drivers in one go. The changes to the
buslogic driver go beyond just this - the whole driver was new-bus'ed
including pci and isa. I have only tested the EISA part of this so far.
Submitted by: Doug Rabson <dfr@nlsystems.com>
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
driver was thinking irq was enabled although it wasn't.
This case was particular to a no-interrupt static configuration.
Reported by: "Norman C. Rice" <nrice@emu.sourcee.com>
peripheral drivers can determine where in the devstat(9) list they are
inserted.
This requires recompilation of libdevstat, systat, vmstat, rpc.rstatd, and
any ports that depend on the devstat code, since the size of the devstat
structure has changed. The devstat version number has been incremented as
well to reflect the change.
This sorts devices in the devstat list in "more interesting" to "less
interesting" order. So, for instance, da devices are now more important
than floppy drives, and so will appear before floppy drives in the default
output from systat, iostat, vmstat, etc.
The order of devices is, for now, kept in a central table in devicestat.h.
If individual drivers were able to make a meaningful decision on what
priority they should be at attach time, we could consider splitting the
priority information out into the various drivers. For now, though, they
have no way of knowing that, so it's easier to put them in an easy to find
table.
Also, move the checkversion() call in vmstat(8) to a more logical place.
Thanks to Bruce and David O'Brien for suggestions, for reviewing this, and
for putting up with the long time it has taken me to commit it. Bruce did
object somewhat to the central priority table (he would rather the
priorities be distributed in each driver), so his objection is duly noted
here.
Reviewed by: bde, obrien
the screen width.
- Store the current video mode information in the `video_adapter' struct.
- The size of the `v_offscreensize' field in the VESA mode information
block is u_int16, not u_int8.
Change microseq offsets. Previously, offsets of the program counter where
added to the index of the current microinstruction. Make them rely on the
index of the next executed microinstruction.
Suggested by: Luigi Rizzo <luigi@labinfo.iet.unipi.it>
