on a "NQNFS" kernel config option. NQNFS is a 4.4 wart and the performance
penalty of the lease checks on the client/server for _local_ I/O is too high
to have this occur all the time - especially when most people will never
use it.
Install the biosboot as /usr/mdec/boot[12]
Make the traditional links from [swf]dboot and boot[swf]d to boot[12] files.
Install dosboot as /usr/mdec/boot/fbsdboot.exe
1) Preserve old buffer contents when input buffer overflows.
Old code clear buffer and rewrite it again, if !MAXBEL
(for MAXBEL it does right thing :-).
F.e. if you type too long string, last chars passed,
not first ones as expected.
Moreover, it flush output queue too in this case without any needs.
2) Don't do IXOFF, if IGNCR and c==\r, ignore completely.
3) If PARMRK is active and !ISTRIP and char == 0377
put yet one 0377 to distinguish it from parity mark sequence.
POSIX standard (thanx Bruce).
Reviewed by:
Submitted by:
Obtained from:
CVS:
if (tp->t_line != 0)
test when CS_ODONE, it fails for NTTYDISC, use
if (linesw[tp->t_line].l_start != ttstart)
instead.
Reviewed by:
Submitted by:
Obtained from:
CVS:
BREAK/parity/framing errors.
Term "correctly" assumes POSIX spec. and 4.4 ttyinput() behaviour.
1) Discard BREAK/parity at interrupt level when apropriate IGN*
is set in iflag. It helps "raw" mode works even IGN* is set.
2) Zero parity (if INPCK) and framing directly in buffer
before passing it to b_to_q() in "raw" mode.
Efficency:
interrupt level: if no error occurse, only two "test" commands added
"raw" mode: buf scan incc times for parity/framing added
Reviewed by:
Submitted by:
Obtained from:
CVS:
merged cache changes, and figure it out based on the B_VMIO buffer flag.
Fixes a problem where delayed write VMIO buffers would sometimes get
recopied into kernel-alloced memory.
Submitted by: John Dyson
Report floppy/tape units on seperate lines as fdX:/ftX: to correct lots of
ways the current scheme failed to end the output with \n.
Add controller and/or drive designator to the fron of several messages
that come from this drive. [It's not fun to track down driver messages
using grep over the source tree.]
Reviewed by: joerg
include <pci/pcivar.h> without including <sys/devconf.h> and other
drivers include <pci/pcivar.h> before including <sys/devconf.h> if
certain identifiers are defined.
The devconf headers have convoluted interdependencies. <sys/devconf.h>
includes <machine/devconf.h> which includes <pci/pcivar.h>. Most
drivers include <sys/devconf.h> so even isa drivers depend on
<pci/pcivar.h>. For similar reasons, most drivers depend on another
pci header, on an isa header and on two scsi headers.
- ignore the partition table if it is identical with the bogus one in
/usr/src/sys/i386/boot/biosboot/start.S. Honoring the bogus size
field was fatal. The error is detected but other compatibilty
cruft weakens the error handling too much for this case.
- weaken the partition entry checking to allow the following treatments
of C/H/S addresses when C should be >= 1024:
(1) allow C = 1023, H = max, S = max.
(2) allow C to be correct modulo 1024.
Other compatibilty cruft weakens the error handling to allow all
C/H/S addresses, but there too many errors were reported.
Improve error messages:
- print C/H/S addresses if relevant.
- distinguish primary partition table from extended partition tables.
- don't use diskerr() except for i/o errors.
