lives in ext2_vnops.c for ext2fs. Also remove cast from comparision.
Bruce pointed out that it was bogus since we'd force a signed
comparision when we really wanted an unsigned comparison.
to write all the dirty blocks. If some of those blocks have dependencies,
they will be remarked dirty when the I/O completes. On systems with
really fast I/O systems, it is possible to get in an infinite loop trying
to flush the buffers, because the I/O finishes before we can get all the
dirty buffers off the v_dirtyblkhd list and into the I/O queue. (The
previous algorithm looped over the v_dirtyblkhd list writing out buffers
until the list emptied.) So, now we mark each buffer that we try to
write so that we can distinguish the ones that are being remarked dirty
from those that we have not yet tried to flush. Once we have tried to
push every buffer once, we then push any associated metadata that is
causing the remaining buffers to be redirtied.
Submitted by: Matthew Dillon <dillon@apollo.backplane.com>
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
tulip_addr_filter() on SIOCSIFFLAGS, and was nuking the IFF_ALLMULTI
on entering tulip_addr_filter(). As a result it was impossible to run
a multicast router on a machine with a "de" interface.
already defined. This allows for cross building to work because we
need to lie to make to tell it to use the target names rather than the
host names.
This should have no effect on either architecture. I've confirmed
that the intel build by make buildworld's for the past 3 months.
catch a T4000s)
+ Set *some* kind of error at EOM if we're in fixed mode and have pending errs.
Do not clear the ERR_PENDING bit if more buffers are queued.
+ Release the start_ccb in this case also, else we hang forever on rewinding.
+ Any kind of error for load to BOT in samount should then cause an attempt
to use REWIND to come back to BOT. Do the initial load command quietly.
+ In samount, if we succeed, set the relative position markers.
not per-process. Keep it in `switchtime' consistently.
It is now clear that the timestamp is always valid in fork_trampoline()
except when the child is running on a previously idle cpu, which
can only happen if there are multiple cpus, so don't check or set
the timestamp in fork_trampoline except in the (i386) SMP case.
Just remove the alpha code for setting it unconditionally, since
there is no SMP case for alpha and the code had rotted.
Parts reviewed by: dfr, phk
Submitted by: Matthew Dillon <dillon@apollo.backplane.com>
To prevent a deadlock, if we are extremely low on memory, force synchronous
operation by the VOP_PUTPAGES in vnode_pager_putpages.
to calculate a reasonable size for the swap partition).
* Fix a typo in remrq() where a process with idle priority would not be
correctly removed from the relavent queue. Note that realtime and idle
priorities are still not supported since the assembler code in
cpu_switch() does not check the realtime and idle queues.
- Transparent proxying support added.
- PPTP redirecting support added based on patches
contributed by Dru Nelson <dnelson@redwoodsoft.com>.
Submitted by: Charles Mott <cmott@srv.net>
drive has very poor write performance (1.4MB/sec vs. 12MB/sec) with anything
more than two oustanding transactions.
So, this limits the number of tagged commands to two for that drive.
Thanks to Paul van der Zwan for doing a whole lot of testing to confirm
this.
Reported by: Paul van der Zwan <paulz@trantor.xs4all.nl>
Specifically, the test was in the wrong place, lacked a cast, didn't
unlock the node, and exited to bad rather than abortit. Now we don't
allow renaming of a file with LINK_MAX references. Move the test to
earlier in the code as it is closer to where ip is obtained, as that
is the style of the rest of the function.
Didn't fix the problems bruce pointed out in the rename man page to
include EMLINK, nor address his complaints about how the whole idea of
incrementing the link count during a rename is potentially asking for
trouble.
Also didn't try to correct potential problem Terry pointed out with
decrements not being similarly protected against underflow.
Added autodetection of MMAC Osprey 100 card for
Jan Schmidt <mmedia@rz.uni-greifswald.de>. The MMAC card has an EEPROM
which contains an ASCII string beginning with "MMAC".
Corrected Hauppauge Audio Mux Mute value from 0x01 to 0x04.
Fixed a typo.
Sumitted change:
Added ALPS Tuner Type submitted by Hiroki Mori <mori@infocity.co.jp>
Submitted by: Roger Hardiman and Hiroki Mori <mori@infocity.co.jp>
Add d_parms() to {c,b}devsw[]. If non-NULL this function points to
a device routine that will properly fill in the specinfo structure.
vfs_subr.c's checkalias() supplies appropriate defaults. This change
should be fully backwards compatible with existing devices.
routine was [ab]used for two different things, and you couldn't tell from
the wait channel which one had wedged.
Catch a few things missing from NFS_NOSERVER.
