ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
reassigning their v_ops field to specfs, detaching from the mountpoint, etc.
However, this is not sufficient. If we vclean() the vnode the pages owned
by the vnode are lost, potentially while buffers reference them. Implement
parts of vclean() seperately in vgonechrl() so that the pages and bufs
associated with a device vnode are not destroyed while in use.
correctly, resulting in the dreaded "vm_pageout_flush: partially
invalid page" panic. The caching issue will be revisited in the
future, but opt for safety over performance in the meantime.
Tested by: gallatin
this definition. It fixes gnome for starters. I haven't tried *emacs yet.
Like IA64, amd64 uses registers for the first few arguments and then
the stack for the rest. This means the 64 bit promotion of the NULL (0)
value is lost and its just pushed on as an 'int' in a varargs call.
When the consumer walks the list and expects to pull off void * pointers
via va_arg, then all hell breaks loose.
Marcel: thanks a million for finding this!
the psim simulator. Look for the "file" property which only exists
on psim disks, and as a bonus, print the contents of this at boot-time,
which is the host file being used for the disk image.
- remove remaining warnings.
transfer size to the stripe size. This is a different
situation from reviving, where this limitation is necessary.
In initsd we're simply writing binary zeroes to the entire
disk, so the only effect of limiting the transfer is to slow
things down.
ndis_send_packets() but there's no link yet, we get an immediate
callback to ndis_txeof(), which clears if_timer. But ndis_start()
sets if_timer right after the call to ndis_send_packets(). Set
if_timer before calling ndis_send_packets().
Also fix mutex locking to prevent ndis_txeof() from running in
the middle of ndis_start().
make it more robust. This should fix problems with crashes under
heavy traffic loads that have been reported. Also add a 'query done'
callback handler to satisfy the e100bex.sys sample Intel driver.
eventually be passed an async. context as well as a syscall
context.
While here, fix a serious bug in that if the trapframe is a
syscall frame, but we're restoring an async context, we need
to clear the FRAME_SYSCALL flag so that we leave the kernel
via exception_restore.
NdisAnsiStringToUnicodeString(), NdisWriteConfiguration().
Also add stubs for NdisMGetDeviceProperty(), NdisTerminateWrapper(),
NdisOpenConfigurationKeyByName(), NdisOpenConfigurationKeyByIndex()
and NdisMGetDeviceProperty().
- fix ndis_time() so that it returns a time based on the proper
epoch (wacky though it may be)
- implement NdisInitializeString() and NdisFreeString(), and add
stub for NdisMRemoveMiniport()
ntoskrnl_var.h:
- add missing member to the general_lookaside struct (gl_listentry)
subr_ntoskrnl.c:
- Fix arguments to the interlocked push/pop routines: 'head' is an
slist_header *, not an slist_entry *
- Kludge up _fastcall support for the push/pop routines. The _fastcall
convention is similar to _stdcall, except the first two available
DWORD-sized arguments are passed in %ecx and %edx, respectively.
One kludge for this __attribute__ ((regparm(3))), however this
isn't entirely right, as it assumes %eax, %ecx and %edx will be
used (regparm(2) assumes %eax and %edx). Another kludge is to
declare the two fastcall-ed args as local register variables and
explicitly assign them to %ecx and %edx, but experimentation showed
that gcc would not guard %ecx and %edx against being clobbered.
Thus, I came up with a 3rd kludge, which is to use some inline
assembly of the form:
void *arg1;
void *arg2;
__asm__("movl %%ecx, %%ecx" : "=c" (arg1));
__asm__("movl %%edx, %%edx" : "=d" (arg2));
This lets gcc know that we're going to reference %ecx and %edx and
that it should make an effort not to let it get trampled. This wastes
an instruction (movl %reg, %reg is a no-op) but insures proper
behavior. It's possible there's a better way to do this though:
this is the first time I've used inline assembler in this fashion.
The above fixes to ntoskrnl_var.h an subr_ntoskrnl.c make lookaside
lists work for the two drivers I have that use them, one of which
is an NDIS 5.0 miniport and another which is 5.1.
subr_ndis.c: NdisGetCurrentSystemTime() which, according to the
Microsoft documentation returns "the number of 100 nanosecond
intervals since January 1, 1601." I have no idea what's so special
about that epoch or why they chose 100 nanosecond ticks. I don't
know the proper offset to convert nanotime() from the UNIX epoch
to January 1, 1601, so for now I'm just doing the unit convertion
to 100s of nanoseconds.
subr_ntoskrnl.c: memcpy(), memset(), ExInterlockedPopEntrySList(),
ExInterlockedPushEntrySList().
The latter two are different from InterlockedPopEntrySList()
and InterlockedPushEntrySList() in that they accept a spinlock to
hold while executing, whereas the non-Ex routines use a lock
internal to ntoskrnl. I also modified ExInitializePagedLookasideList()
and ExInitializeNPagedLookasideList() to initialize mutex locks
within the lookaside structures. It seems that in NDIS 5.0,
the lookaside allocate/free routines ExInterlockedPopEntrySList()
and ExInterlockedPushEntrySList(), which require the use of the
per-lookaside spinlock, whereas in NDIS 5.1, the per-lookaside
spinlock is deprecated. We need to support both cases.
Note that I appear to be doing something wrong with
ExInterlockedPopEntrySList() and ExInterlockedPushEntrySList():
they don't appear to obtain proper pointers to their arguments,
so I'm probably doing something wrong in terms of their calling
convention (they're declared to be FASTCALL in Widnows, and I'm
not sure what that means for gcc). It happens that in my stub
lookaside implementation, they don't need to do any work anyway,
so for now I've hacked them to always return NULL, which avoids
corrupting the stack. I need to do this right though.
throttling values being available regardless of the CPU's capabilities.
This has been broken since rev 1.1. Also clarify a comment.
Submitted by: Taku YAMAMATO <taku@cent.saitama-u.ac.jp>
Write 100 times for tomorrow:
I will never again free(9) a modified pointer.
Pointy Hat: yeah, yeah, yeah, can you just put it in the pile over there...
Only do short-cable on revisions that need it.
Move generic initialization before short-cable fix, in order to not
clobber short cable fix register setting.
it's an error to set the buffer bytecount to anything larger than
the buffer's original allocation size, but anything less than that
is ok.
Also, in ndis_ptom(), use the same logic: if the bytecount is
larger than the allocation size, consider the bytecount invalid
and the allocation size as the packet fragment length (m_len)
instead of the bytecount.
This corrects a consistency problem between the Broadcom wireless
driver and some of the ethernet drivers I've tested: the ethernet
drivers all report the packet frag sizes in buf->nb_bytecount, but
the Broadcom wireless driver reports them in buf->nb_size. This
seems like a bug to me, but it clearly must work in Windows, so
we have to deal with it here too.
- The new sched_balance_groups() function does intra-group balancing while
sched_balance() balances the available groups.
- Pick a random time between 0 ticks and hz * 2 ticks to restart each
balancing process. Each balancer has its own timeout.
- Pick a random place in the list of groups to start the search for lowest
and highest group loads. This prevents us from prefering a group based on
numeric position.
- Use a nasty hack to stop us from preferring cpu 0. The problem is that
softclock always runs on cpu 0, so it always has a little extra load. We
ignore this load in the balancer for now. In the future softclock should
run on a random cpu and these hacks can go away.
is provided to NDIS via the the miniport characteristics structure
supplied in the call to NdisMRegisterMiniport(). But in NDIS 5.0
and earlier, you had to call NdisMRegisterAdapterShutdownHandler()
and supply both a function pointer and context pointer.
We try to handle both cases in ndis_shutdown_nic(). If the
driver registered a shutdown routine and a context,then used
that context, otherwise pass it the adapter context from
NdisMSetAttributesEx().
This fixes a panic on shutdown with the sample Intel 82559 e100bex.sys
driver from the Windows DDK.
function pointer
