Compile sys/dev/mem/memutil.c for all supported platforms and remove now
unnecessary dev_mem_md_init(). Consistently define mem_range_softc from
mem.c for all platforms. Add missing #include guards for machine/memdev.h
and sys/memrange.h. Clean up some nearby style(9) nits.
MFC after: 1 month
TSB is located within the 32-bit address space, which held true as long as
we were using virtual addresses magic-mapped before the location of the
kernel for addressing it. However, with r216803 in place when possible we
address it via its physical address instead, which on machines like Sun Fire
V880 have no physical memory in the 32-bit address space at all requires
to use 64-bit addressing. When using physical addressing it still should
be safe to assume that we can just ignore the lowest 10 bits of the address
as a minor optimization as we did before r216803.
architecture macros (__mips_n64, __powerpc64__) when 64 bit types (and
corresponding macros) are different from 32 bit. [1]
Correct the type of INT64_MIN, INT64_MAX and UINT64_MAX.
Define (U)INTMAX_C as an alias for (U)INT64_C matching the type definition
for (u)intmax_t. Do this on all architectures for consistency.
Suggested by: bde [1]
Approved by: kib (mentor)
On some architectures UCHAR_MAX and USHRT_MAX had type unsigned int.
However, lacking integer suffixes for types smaller than int, their type
should correspond to that of an object of type unsigned char (or short)
when used in an expression with objects of type int. In that case unsigned
char (short) are promoted to int (i.e. signed) so the type of UCHAR_MAX and
USHRT_MAX should also be int.
Where MIN/MAX constants implicitly have the correct type the suffix has
been removed.
While here, correct some comments.
Reviewed by: bde
Approved by: kib (mentor)
and switch sparc64 to use the first one for bus error filter handlers of
bridge drivers instead of (ab)using INTR_FAST for that so we eventually
can get rid of the latter.
Reviewed by: jhb
MFC after: 1 month
functions, otherwise if we get preempted after checking whether a certain
pmap is active on the current CPU but before disabling interrupts we might
operate on an outdated state as the pmap might have been deactivated in
the meantime. As the same issue may arises when the TLB demap function is
interrupted by a TLB demap IPI, just entering a critical section before
the check isn't sufficient so we have to fully disable interrupts instead.
MFC after: 3 days
which takes an physical address instead of an virtual one, for loading TTEs
of the kernel TSB so we no longer need to lock the kernel TSB into the dTLB,
which only has a very limited number of lockable dTLB slots. The net result
is that we now basically can handle a kernel TSB of any size and no longer
need to limit the kernel address space based on the number of dTLB slots
available for locked entries. Consequently, other parts of the trap handlers
now also only access the the kernel TSB via its physical address in order
to avoid nested traps, as does the PMAP bootstrap code as we haven't taken
over the trap table at that point, yet. Apart from that the kernel TSB now
is accessed via a direct mapping when we are otherwise taking advantage of
ASI_ATOMIC_QUAD_LDD_PHYS so no further code changes are needed. Most of this
is implemented by extending the patching of the TSB addresses and mask as
well as the ASIs used to load it into the trap table so the runtime overhead
of this change is rather low. Currently the use of ASI_ATOMIC_QUAD_LDD_PHYS
is not yet enabled on SPARC64 CPUs due to lack of testing and due to the
fact it might require minor adjustments there.
Theoretically it should be possible to use the same approach also for the
user TSB, which already is not locked into the dTLB, avoiding nested traps.
However, for reasons I don't understand yet OpenSolaris only does that with
SPARC64 CPUs. On the other hand I think that also addressing the user TSB
physically and thus avoiding nested traps would get us closer to sharing
this code with sun4v, which only supports trap level 0 and 1, so eventually
we could have a single kernel which runs on both sun4u and sun4v (as does
Linux and OpenBSD).
Developed at and committed from: 27C3
STICK/STICK_COMPARE independently of the selected instruction set by
TICK_COMPARE so tick.c as of r214358 once again can be compiled with
gcc -mcpu=v9 for reference purposes.
kernel address space in order to leave space for the buffer cache, pipes,
thread stacks, etc on machines with more physical memory until we take
advantage of ASI_ATOMIC_QUAD_LDD_PHYS on CPUs providing it so we don't need
to lock the kernel TSB pages into the dTLB, basically making the entire
64-bit kernel address space available on relevant machines.
Submitted by: alc
Passing a count of zero on i386 and amd64 for [I386|AMD64]_BUS_SPACE_MEM
causes a crash/hang since the 'loop' instruction decrements the counter
before checking if it's zero.
PR: kern/80980
Discussed with: jhb
DEBUG_MEMGUARD panics early in kmeminit() with the message
"kmem_suballoc: bad status return of 1" because of zero "size" argument
passed to kmem_suballoc() due to "vm_kmem_size_max" being zero.
The problem also exists on ia64.
creation of large page mappings in the pmap, it can provide modest
performance benefits. In particular, for a "buildworld" on a 2x 1GHz
Ultrasparc IIIi it reduced the wall clock time by 2.2% and the system
time by 12.6%.
Tested by: marius@
contents of the ones that were not empty were stale and unused.
- Now that <machine/mutex.h> no longer exists, there is no need to allow it
to override various helper macros in <sys/mutex.h>.
- Rename various helper macros for low-level operations on mutexes to live
in the _mtx_* or __mtx_* namespaces. While here, change the names to more
closely match the real API functions they are backing.
- Drop support for including <sys/mutex.h> in assembly source files.
Suggested by: bde (1, 2)
work properly with single-stepping in a kernel debugger. Specifically,
these routines have always disabled interrupts before increasing the nesting
count and restored the prior state of interrupts after decreasing the nesting
count to avoid problems with a nested interrupt not disabling interrupts
when acquiring a spin lock. However, trap interrupts for single-stepping
can still occur even when interrupts are disabled. Now the saved state of
interrupts is not saved in the thread until after interrupts have been
disabled and the nesting count has been increased. Similarly, the saved
state from the thread cannot be read once the nesting count has been
decreased to zero. To fix this, use temporary variables to store interrupt
state and shuffle it between the thread's MD area and the appropriate
registers.
In cooperation with: bde
MFC after: 1 month
need locking as otherwise we may race against the other parts of the
MD code which expects a consistent state of these. While at it move
the resetting of the pmap before entering it in the TSB.
- Spell a 0 as TLB_CTX_KERNEL.
introduce function pointers once set up to the respective implementation
for reading the (S)TICK and writing the (S)STICK_COMPARE registers as a
compromise between duplicating code and selecting between different
implementations during execution over and over again, similar to what is
done elsewhere in the MD in order to support different CPU models that
won't ever change at runtime.
- In the remaining tick interrupt handler further push down disabling of
interrupts to the periodic case as it isn't necessary here in one-shot
mode at all.
a critical section as apparently required by both. I don't think either
belongs in the event timer front-ends but the callback should handle
this as necessary instead just like for example intr_event_handle()
does but this is how the other architectures currently handle it, either
explicitly or implicitly.
- Further rename and reword references to hardclock as this front-end no
longer has a notion of actually calling it.
drift in order to achieve a more stable clock as the tick intervals may
vary in the first place. In fact I haven't seen this code kick in when
in oneshot-mode so just skip it in that case.
- There's no need to explicitly stop the (S)TICK counter in oneshot-mode
with every tick as it just won't trigger again with the (S)TICK compare
register set to a value in the past (with a wrap-around once every ~195
years of uptime at 1.5 GHz this isn't something we have to worry about
in practice).
- Given that we'll disable interrupts completely anyway there's no
need to enter critical sections.
what is done on other platforms. Unlike as with the sched_throw(NULL)
called on BSPs during their startup apparently there's nothing which will
reliably lower it on APs. I'm unsure why this only came up on V215 though,
breaking these with r207248. My best guess is that these are the only
supported ones so far fast enough to loose some race.
PR: 151404
MFC after: 3 days
to the expected type so they work like the corresponding __bswapN_var()
functions and the compiler doesn't complain when arguments of different
width are passed.
The check for alignment should be made against the physical address and not
the virtual address that maps it.
Sponsored by: NetApp
Submitted by: Will McGovern (will at netapp dot com)
Reviewed by: mjacob, jhb
the location, apply elf_relocaddr to the symbol value to have right
values for the symbols from dpcpu segment.
PR: kern/147769
Discussed with: avg
Tested by: marius
MFC after: 2 weeks
additionally takes advantage of the prefetch cache of these CPUs.
Unlike the uncommitted US-III version, which provide no measurable
speedup or even resulted in a slight slowdown on certain CPUs models
compared to using the US-I version with these, the SPARC64 version
actually results in a slight improvement.
- make dflt_lock() always panic,
- add kludge to use contigmalloc() when the alignment is larger than the size
and print a diagnostic when we didn't satisfy the alignment.
unlikely that support for these ever will be implemented on sparc64 as
the IOMMUs are able to translate to up to the maximum physical address
supported by the respective machine, bypassing the IOMMU is affected
by hardware errata and being able to support DMA engines which cannot
do at least 32-bit DMA does not justify the costs.
- The page zeroing in uma_small_alloc() may use the VIS-based block zero
function so take advantage of it.
of small maxsize and "large" (including BUS_SPACE_UNRESTRICTED) nsegments
parameters. Generally using a presz of 0 (which indeed might indicate the
use of bogus parameters for DMA tag creation) is not fatal, it just means
that no additional DVMA space will be preallocated.
The main goal of this is to generate timer interrupts only when there is
some work to do. When CPU is busy interrupts are generating at full rate
of hz + stathz to fullfill scheduler and timekeeping requirements. But
when CPU is idle, only minimum set of interrupts (down to 8 interrupts per
second per CPU now), needed to handle scheduled callouts is executed.
This allows significantly increase idle CPU sleep time, increasing effect
of static power-saving technologies. Also it should reduce host CPU load
on virtualized systems, when guest system is idle.
There is set of tunables, also available as writable sysctls, allowing to
control wanted event timer subsystem behavior:
kern.eventtimer.timer - allows to choose event timer hardware to use.
On x86 there is up to 4 different kinds of timers. Depending on whether
chosen timer is per-CPU, behavior of other options slightly differs.
kern.eventtimer.periodic - allows to choose periodic and one-shot
operation mode. In periodic mode, current timer hardware taken as the only
source of time for time events. This mode is quite alike to previous kernel
behavior. One-shot mode instead uses currently selected time counter
hardware to schedule all needed events one by one and program timer to
generate interrupt exactly in specified time. Default value depends of
chosen timer capabilities, but one-shot mode is preferred, until other is
forced by user or hardware.
kern.eventtimer.singlemul - in periodic mode specifies how much times
higher timer frequency should be, to not strictly alias hardclock() and
statclock() events. Default values are 2 and 4, but could be reduced to 1
if extra interrupts are unwanted.
kern.eventtimer.idletick - makes each CPU to receive every timer interrupt
independently of whether they busy or not. By default this options is
disabled. If chosen timer is per-CPU and runs in periodic mode, this option
has no effect - all interrupts are generating.
As soon as this patch modifies cpu_idle() on some platforms, I have also
refactored one on x86. Now it makes use of MONITOR/MWAIT instrunctions
(if supported) under high sleep/wakeup rate, as fast alternative to other
methods. It allows SMP scheduler to wake up sleeping CPUs much faster
without using IPI, significantly increasing performance on some highly
task-switching loads.
Tested by: many (on i386, amd64, sparc64 and powerc)
H/W donated by: Gheorghe Ardelean
Sponsored by: iXsystems, Inc.
This reflects actual type used to store and compare child device orders.
Change is mostly done via a Coccinelle (soon to be devel/coccinelle)
semantic patch.
Verified by LINT+modules kernel builds.
Followup to: r212213
MFC after: 10 days
In particular, provide pagesize and pagesizes array, the canary value
for SSP use, number of host CPUs and osreldate.
Tested by: marius (sparc64)
MFC after: 1 month
td_critnest > 1 when not already running on the desired CPU read the
TICK counter of the BSP via a direct cross trap request in that case
instead.
- Treat the STICK based timecounter the same way as the TICK based one
regarding its quality and obtaining the counter value from the BSP.
Like the TICK timers the STICK ones also are only synchronized during
their startup (which might not result in good synchronicity in the
first place) but not afterwards and might drift over time, causing
problems when the time is read from different CPUs (see r135972).
to single CPUs more efficiently with Cheetah(-class) and Jalapeno CPUs.
Besides being used to implement the ipi_cpu() introduced in r210939,
cpu_ipi_single() will also be used internally by the sparc64 MD code.
- Factor out the Jalapeno support from the Cheetah IPI send functions
in order to be able to more easily and efficiently implement support
for more than 32 target CPUs as well as a workaround for Cheetah+
erratum 25 for the latter.
IPI to a specific CPU by its cpuid. Replace calls to ipi_selected() that
constructed a mask for a single CPU with calls to ipi_cpu() instead. This
will matter more in the future when we transition from cpumask_t to
cpuset_t for CPU masks in which case building a CPU mask is more expensive.
Submitted by: peter, sbruno
Reviewed by: rookie
Obtained from: Yahoo! (x86)
MFC after: 1 month
zones for each malloc bucket size. The purpose is to isolate
different malloc types into hash classes, so that any buffer overruns
or use-after-free will usually only affect memory from malloc types in
that hash class. This is purely a debugging tool; by varying the hash
function and tracking which hash class was corrupted, the intersection
of the hash classes from each instance will point to a single malloc
type that is being misused. At this point inspection or memguard(9)
can be used to catch the offending code.
Add MALLOC_DEBUG_MAXZONES=8 to -current GENERIC configuration files.
The suggestion to have this on by default came from Kostik Belousov on
-arch.
This code is based on work by Ron Steinke at Isilon Systems.
Reviewed by: -arch (mostly silence)
Reviewed by: zml
Approved by: zml (mentor)
now it uses a very dumb first-touch allocation policy. This will change in
the future.
- Each architecture indicates the maximum number of supported memory domains
via a new VM_NDOMAIN parameter in <machine/vmparam.h>.
- Each cpu now has a PCPU_GET(domain) member to indicate the memory domain
a CPU belongs to. Domain values are dense and numbered from 0.
- When a platform supports multiple domains, the default freelist
(VM_FREELIST_DEFAULT) is split up into N freelists, one for each domain.
The MD code is required to populate an array of mem_affinity structures.
Each entry in the array defines a range of memory (start and end) and a
domain for the range. Multiple entries may be present for a single
domain. The list is terminated by an entry where all fields are zero.
This array of structures is used to split up phys_avail[] regions that
fall in VM_FREELIST_DEFAULT into per-domain freelists.
- Each memory domain has a separate lookup-array of freelists that is
used when fulfulling a physical memory allocation. Right now the
per-domain freelists are listed in a round-robin order for each domain.
In the future a table such as the ACPI SLIT table may be used to order
the per-domain lookup lists based on the penalty for each memory domain
relative to a specific domain. The lookup lists may be examined via a
new vm.phys.lookup_lists sysctl.
- The first-touch policy is implemented by using PCPU_GET(domain) to
pick a lookup list when allocating memory.
Reviewed by: alc
between determining the other CPUs and calling cpu_ipi_selected(), which
apart from generally doing the wrong thing can lead to a panic when a
CPU is told to IPI itself (which sun4u doesn't support).
Reported and tested by: Nathaniel W Filardo
- Add __unused where appropriate.
MFC after: 3 days
allow pmap_enter() to be performed on an unmanaged page that doesn't have
VPO_BUSY set. Having VPO_BUSY set really only matters for managed pages.
(See, for example, pmap_remove_write().)
PG_REFERENCED changes in vm_pageout_object_deactivate_pages().
Simplify this function's inner loop using TAILQ_FOREACH(), and shorten
some of its overly long lines. Update a stale comment.
Assert that PG_REFERENCED may be cleared only if the object containing
the page is locked. Add a comment documenting this.
Assert that a caller to vm_page_requeue() holds the page queues lock,
and assert that the page is on a page queue.
Push down the page queues lock into pmap_ts_referenced() and
pmap_page_exists_quick(). (As of now, there are no longer any pmap
functions that expect to be called with the page queues lock held.)
Neither pmap_ts_referenced() nor pmap_page_exists_quick() should ever
be passed an unmanaged page. Assert this rather than returning "0"
and "FALSE" respectively.
ARM:
Simplify pmap_page_exists_quick() by switching to TAILQ_FOREACH().
Push down the page queues lock inside of pmap_clearbit(), simplifying
pmap_clear_modify(), pmap_clear_reference(), and pmap_remove_write().
Additionally, this allows for avoiding the acquisition of the page
queues lock in some cases.
PowerPC/AIM:
moea*_page_exits_quick() and moea*_page_wired_mappings() will never be
called before pmap initialization is complete. Therefore, the check
for moea_initialized can be eliminated.
Push down the page queues lock inside of moea*_clear_bit(),
simplifying moea*_clear_modify() and moea*_clear_reference().
The last parameter to moea*_clear_bit() is never used. Eliminate it.
PowerPC/BookE:
Simplify mmu_booke_page_exists_quick()'s control flow.
Reviewed by: kib@
pmap_is_referenced(). Eliminate the corresponding page queues lock
acquisitions from vm_map_pmap_enter() and mincore(), respectively. In
mincore(), this allows some additional cases to complete without ever
acquiring the page queues lock.
Assert that the page is managed in pmap_is_referenced().
On powerpc/aim, push down the page queues lock acquisition from
moea*_is_modified() and moea*_is_referenced() into moea*_query_bit().
Again, this will allow some additional cases to complete without ever
acquiring the page queues lock.
Reorder a few statements in vm_page_dontneed() so that a race can't lead
to an old reference persisting. This scenario is described in detail by a
comment.
Correct a spelling error in vm_page_dontneed().
Assert that the object is locked in vm_page_clear_dirty(), and restrict the
page queues lock assertion to just those cases in which the page is
currently writeable.
Add object locking to vnode_pager_generic_putpages(). This was the one
and only place where vm_page_clear_dirty() was being called without the
object being locked.
Eliminate an unnecessary vm_page_lock() around vnode_pager_setsize()'s call
to vm_page_clear_dirty().
Change vnode_pager_generic_putpages() to the modern-style of function
definition. Also, change the name of one of the parameters to follow
virtual memory system naming conventions.
Reviewed by: kib
independent code. Move this code into mincore(), and eliminate the
page queues lock from pmap_mincore().
Push down the page queues lock into pmap_clear_modify(),
pmap_clear_reference(), and pmap_is_modified(). Assert that these
functions are never passed an unmanaged page.
Eliminate an inaccurate comment from powerpc/powerpc/mmu_if.m:
Contrary to what the comment says, pmap_mincore() is not simply an
optimization. Without a complete pmap_mincore() implementation,
mincore() cannot return either MINCORE_MODIFIED or MINCORE_REFERENCED
because only the pmap can provide this information.
Eliminate the page queues lock from vfs_setdirty_locked_object(),
vm_pageout_clean(), vm_object_page_collect_flush(), and
vm_object_page_clean(). Generally speaking, these are all accesses
to the page's dirty field, which are synchronized by the containing
vm object's lock.
Reduce the scope of the page queues lock in vm_object_madvise() and
vm_page_dontneed().
Reviewed by: kib (an earlier version)
Extend struct sysvec with three new elements:
sv_fetch_syscall_args - the method to fetch syscall arguments from
usermode into struct syscall_args. The structure is machine-depended
(this might be reconsidered after all architectures are converted).
sv_set_syscall_retval - the method to set a return value for usermode
from the syscall. It is a generalization of
cpu_set_syscall_retval(9) to allow ABIs to override the way to set a
return value.
sv_syscallnames - the table of syscall names.
Use sv_set_syscall_retval in kern_sigsuspend() instead of hardcoding
the call to cpu_set_syscall_retval().
The new functions syscallenter(9) and syscallret(9) are provided that
use sv_*syscall* pointers and contain the common repeated code from
the syscall() implementations for the architecture-specific syscall
trap handlers.
Syscallenter() fetches arguments, calls syscall implementation from
ABI sysent table, and set up return frame. The end of syscall
bookkeeping is done by syscallret().
Take advantage of single place for MI syscall handling code and
implement ptrace_lwpinfo pl_flags PL_FLAG_SCE, PL_FLAG_SCX and
PL_FLAG_EXEC. The SCE and SCX flags notify the debugger that the
thread is stopped at syscall entry or return point respectively. The
EXEC flag augments SCX and notifies debugger that the process address
space was changed by one of exec(2)-family syscalls.
The i386, amd64, sparc64, sun4v, powerpc and ia64 syscall()s are
changed to use syscallenter()/syscallret(). MIPS and arm are not
converted and use the mostly unchanged syscall() implementation.
Reviewed by: jhb, marcel, marius, nwhitehorn, stas
Tested by: marcel (ia64), marius (sparc64), nwhitehorn (powerpc),
stas (mips)
MFC after: 1 month
hook it up to ada(4) also. While at it, rename *ad_firmware_geom_adjust()
to *ata_disk_firmware_geom_adjust() etc now that these are no longer
limited to ad(4).
Reviewed by: mav
MFC after: 3 days
here, make the style of assertion used by pmap_enter() consistent
across all architectures.
On entry to pmap_remove_write(), assert that the page is neither
unmanaged nor fictitious, since we cannot remove write access to
either kind of page.
With the push down of the page queues lock, pmap_remove_write() cannot
condition its behavior on the state of the PG_WRITEABLE flag if the
page is busy. Assert that the object containing the page is locked.
This allows us to know that the page will neither become busy nor will
PG_WRITEABLE be set on it while pmap_remove_write() is running.
Correct a long-standing bug in vm_page_cowsetup(). We cannot possibly
do copy-on-write-based zero-copy transmit on unmanaged or fictitious
pages, so don't even try. Previously, the call to pmap_remove_write()
would have failed silently.
implementation.
- Revert the Sun Fire V890 WAR of r205254. Instead let schizo_pci_bus()
only panic in case of fatal errors as the interrupt triggered by the
error the firmware of these and also Sun Fire 280R with version 7
Schizo caused may happen as late as using the HBA and not only prior
to touching the PCI bus (in the former case the actual error still is
fatal but we clear it before touching the PCI bus).
While at it count and export non-fatal error interrupts via sysctl(9).
- Remove unnecessary locking from schizo_ue().
vm_page_try_to_free(). Consequently, push down the page queues lock into
pmap_enter_quick(), pmap_page_wired_mapped(), pmap_remove_all(), and
pmap_remove_write().
Push down the page queues lock into Xen's pmap_page_is_mapped(). (I
overlooked the Xen pmap in r207702.)
Switch to a per-processor counter for the total number of pages cached.
pmap_page_is_mapped() in preparation for removing page queues locking
around calls to vm_page_free(). Setting aside the assertion that calls
pmap_page_is_mapped(), vm_page_free_toq() now acquires and holds the page
queues lock just long enough to actually add or remove the page from the
paging queues.
Update vm_page_unhold() to reflect the above change.
HAL/Fujitsu) CPUs. For the most part this consists of fleshing out the
MMU and cache handling, it doesn't add pmap optimizations possible with
these CPU, yet, though.
With these changes FreeBSD runs stable on Fujitsu Siemens PRIMEPOWER 250
and likely also other models based on SPARC64 V like 450, 650 and 850.
Thanks go to Michael Moll for providing access to a PRIMEPOWER 250.
architecture from page queue lock to a hashed array of page locks
(based on a patch by Jeff Roberson), I've implemented page lock
support in the MI code and have only moved vm_page's hold_count
out from under page queue mutex to page lock. This changes
pmap_extract_and_hold on all pmaps.
Supported by: Bitgravity Inc.
Discussed with: alc, jeffr, and kib
Clearing a page table entry's accessed bit and setting the page's
PG_REFERENCED flag in pmap_protect() can't really be justified, so
don't do it. Moreover, on ia64, don't set the page's dirty field
unless pmap_protect() is removing write access.
prevents the firmware of Fujitsu Siemens PRIMEPOWER250, which both causes
stray interrupts and erroneously enables interrupts at least when calling
SUNW,set-trap-table, in the foot.
pmap_ts_referenced() is not always appropriate for checking whether or
not pages have been referenced because it clears any reference bits
that it encounters. For example, in mincore(), clearing the reference
bits has two negative consequences. First, it throws off the activity
count calculations performed by the page daemon. Specifically, a page
on which mincore() has called pmap_ts_referenced() looks less active
to the page daemon than it should. Consequently, the page could be
deactivated prematurely by the page daemon. Arguably, this problem
could be fixed by having mincore() duplicate the activity count
calculation on the page. However, there is a second problem for which
that is not a solution. In order to clear a reference on a 4KB page,
it may be necessary to demote a 2/4MB page mapping. Thus, a mincore()
by one process can have the side effect of demoting a superpage
mapping within another process!
StarCat systems which provides time-of-day services for both as well as
console service for Serengeti, i.e. Sun Fire V1280. While the latter is
described with a device type of serial in the OFW device tree, it isn't
actually an UART. Nevertheless the console service is handled by uart(4)
as this allowed to re-use quite a bit of MD and MI code. Actually, this
idea is stolen from Linux which interfaces the sun4v hypervisor console
with the Linux counterpart of uart(4).
bus we actually mapped at rather than always based on the last bus we
encountered while moving upward in the tree. Otherwise we might use the
wrong bus space in case the bridge directly underneath the nexus doesn't
require mapping, i.e. was skipped as it's the case for ssm(4) nodes.
to the image_params struct instead of several members of that struct
individually. This makes it easier to expand its arguments in the future
without touching all platforms.
Reviewed by: jhb
7 which corresponds to WSTATE_KMIX in OpenSolaris whenever calling into
it which totally screws us even when restoring %wstate afterwards as
spill/fill traps can happen while in OFW. The rather hackish OpenBSD
approach of just setting the equivalent of WSTATE_KERNEL to 7 also is
no option as we treat %wstate as a bit field. So in order to deal with
this problem actually implement spill/fill handlers for %wstate 7 which
just act as the WSTATE_KERNEL ones except of theoretically also handling
32-bit, turn off interrupts completely so we don't even take IPIs while
in OFW which should ensure we only take spill/fill traps at most and
restore %wstate after calling into OFW once we have taken over the trap
table. While at it, actually set WSTATE_{,PROM}_KMIX before calling into
OFW just like OpenSolaris does, which should at least help testing this
change on non-V1280.
- Remove comments referring to the %wstate usage in BSD/OS.
- Remove the no longer used RSF_ALIGN_RETRY macro.
- Correct some trap table addresses in comments.
- Ensure %wstate is set to WSTATE_KERNEL when taking over the trap table.
- Ensure PSTATE_AM is off when entering or exiting to OFW as well as that
interrupts are also completely off when exiting to OFW as the firmware
trap table shouldn't be used to handle our interrupts.
can actually use all of the available lockable entries of the tiny dTLB
for the kernel TSB. With this change the KVA space sizing happens to be
more in line with the MI one so up to at least 24GB machines KVA doesn't
need to be limited manually. This is just another stopgap though, the
real solution is to take advantage of ASI_ATOMIC_QUAD_LDD_PHYS on CPUs
providing it so we don't need to lock the kernel TSB pages into the dTLB
in the first place.
- Swap the configuration of the first and second large dTLB as with
US-IV+ these can only hold entries of certain page sizes each, which
we happened to chose the non-working way around.
- Additionally ensure that the large iTLB is set up to hold 8k pages
(currently this happens to be a NOP though).
- Add a workaround for US-IV+ erratum #2.
- Turn off dTLB parity error reporting as otherwise we get seemingly
false positives when copying in the user window by simulating a
fill trap on return to usermode. Given that these parity errors can
be avoided by disabling multi issue mode and the problem could be
reproduced with a second machine this appears to be a silicon bug of
some sort.
- Add a membar #Sync also before the stores to ASI_DCACHE_TAG. While
at it, turn of interrupts across the whole cheetah_cache_flush() for
simplicity instead of around every flush. This should have next to no
impact as for cheetah-class machines we typically only need to flush
the caches a few times during boot when recovering from peeking/poking
non-existent PCI devices, if at all.
- Just use KERNBASE for FLUSH as we also do elsewhere as the US-IV+
documentation doesn't seem to mention that these CPUs also ignore the
address like previous cheetah-class CPUs do. Again the code changing
LSU_IC is executed seldom enough that the negligible optimization of
using %g0 instead should have no real impact.
With these changes FreeBSD runs stable on V890 equipped with US-IV+
and -j128 buildworlds in a loop for days are no problem. Unfortunately,
the performance isn't were it should be as a buildworld on a 4x1.5GHz
US-IV+ V890 takes nearly 3h while on a V440 with (theoretically) less
powerfull 4x1.5GHz US-IIIi it takes just over 1h. It's unclear whether
this is related to the supposed silicon bug mentioned above or due to
another issue. The documentation (which contains a sever bug in the
description of the bits added to the context registers though) at least
doesn't mention any requirements for changes in the CPU handling besides
those implemented and the cache as well as the TLB configurations and
handling look fine.
o Re-arrange cheetah_init() so it's easier to add support for SPARC64
V up to VIIIfx CPUs, which only require parts of this initialization.
by UltraSparc-IV and -IV+ as well as SPARC64 V, VI, VII and VIIIfx CPUs.
- Replace TLB_PCXR_PGSZ_MASK and TLB_SCXR_PGSZ_MASK with TLB_CXR_PGSZ_MASK
which just is the complement of TLB_CXR_CTX_MASK instead of trying to
assemble it from the page size bits which vary across CPUs.
- Add macros for the remainder of the SFSR bits, which are useful for at
least debugging purposes.
provides no ino-bitmap properties so forge them using the default set
of controller interrupts and let schizo_setup_intr() take care of the
children, hoping for non-fancy routing.
- Add quirk handling for Sun Fire V890. When booting these machines from
disk a Schizo comes up with PCI error residing which triggers as soon
as we register schizo_pci_bus() even when clearing it from all involved
registers (it's no longer indicated once we're in schizo_pci_bus()
though). Thus make PCI bus errors non-fatal until we actually touch the
bus. With this change schizo_pci_bus() typically triggers once during
attach in this case. Obviously this approach isn't exactly race free
but it's about the best we can do about this problem as we're not
guaranteed that the interrupt will actually trigger on V890 either, as
it certainly doesn't when for example netbooting them.
COMPAT_43TTY enables the sgtty interface. Even though its exposure has
only been removed in FreeBSD 8.0, it wasn't used by anything in the base
system in FreeBSD 5.x (possibly even 4.x?). On those releases, if your
ports/packages are less than two years old, they will prefer termios
over sgtty.
but also of different types, f.e. Sun Fire V890 can be equipped with a
mix of UltraSPARC IV and IV+ CPUs, requiring different MMU initialization
and different workarounds for model specific errata. Therefore move the
CPU implementation number from a global variable to the per-CPU data.
Functions which are called before the latter is available are passed the
implementation number as a parameter now.
This file was missed in r204152.
but also of different types, f.e. Sun Fire V890 can be equipped with a
mix of UltraSPARC IV and IV+ CPUs, requiring different MMU initialization
and different workarounds for model specific errata. Therefore move the
CPU implementation number from a global variable to the per-CPU data.
Functions which are called before the latter is available are passed the
implementation number as a parameter now.
scalable shared memory node, which is used in large UltraSPARC III based
machines to group snooping-coherency domains together, like schizo(4) to
be treated like nexus(4) children.
to the exclusion lists as the CPU nodes aren't handled as regular devices
either. Also add the pseudo-devices found in Sun Fire V1280.
- Allow nexus_attach() and nexus_alloc_resource() to be used by drivers
derived from nexus(4) for subordinate busses.
- Don't add the zero-sized memory resources of glue devices to the resource
lists.
root nexus device for the CPUs as starting with UltraSPARC IV the 'cpu'
nodes hang off of from 'cmp' (chip multi-threading processor) or 'core'
or combinations thereof. Also in large UltraSPARC III based machines
the 'cpu' nodes hang off of 'ssm' (scalable shared memory) nodes which
group snooping-coherency domains together instead of directly from the
nexus.
It would be great if we could use newbus to deal with the different ways
the 'cpu' devices can hang off of pseudo ones but unfortunately both
cpu_mp_setmaxid() and sparc64_init() have to work prior to regular device
probing.
- Add support for UltraSPARC IV and IV+ CPUs. Due to the fact that these
are multi-core each CPU has two Fireplane config registers and thus the
module/target ID has to be determined differently so the one specific
to a certain core is used. Similarly, starting with UltraSPARC IV the
individual cores use a different property in the OFW device tree to
indicate the CPU/core ID as it no longer is in coincidence with the
shared slot/socket ID.
This involves changing the MD KTR code to not directly read the UPA
module ID either. We use the MID stored in the per-CPU data instead of
calling cpu_get_mid() as a replacement in order prevent clobbering any
registers as side-effect in the assembler version. This requires CATR()
invocations from mp_startup() prior to mapping the per-CPU pages to be
removed though.
While at it additionally distinguish between CPUs with Fireplane and
JBus interconnects as these also use slightly different sizes for the
JBus/agent/module/target IDs.
- Make sparc64_shutdown_final() static as it's not used outside of
machdep.c.
no cleanwindows handler so just remove trying to trigger it from _start
and the AP trampoline code as that leads to a crash there. This should
be okay as leaking data from the OFW via the CPU registers on start of
the kernel should be no real concern.
- Make the comments of _start and the AP trampoline code regarding the
initializations they perform match each other and reality.
- Make the comments of the AP trampoline code regarding iTLB accesses
refer to the right macro.
of Sun Fire V1280 doesn't round up the size itself but instead lets
claiming of non page-sized amounts of memory fail.
- Change parameters and variables related to the TLB slots to unsigned
which is more appropriate.
- Search the whole OFW device tree instead of only the children of the
root nexus device for the BSP as starting with UltraSPARC IV the 'cpu'
nodes hang off of from 'cmp' (chip multi-threading processor) or 'core'
or combinations thereof. Also in large UltraSPARC III based machines
the 'cpu' nodes hang off of 'ssm' (scalable shared memory) nodes which
group snooping-coherency domains together instead of directly from the
nexus.
- Add support for UltraSPARC IV and IV+ BSPs. Due to the fact that these
are multi-core each CPU has two Fireplane config registers and thus the
module/target ID has to be determined differently so the one specific
to a certain core is used. Similarly, starting with UltraSPARC IV the
individual cores use a different property in the OFW device tree to
indicate the CPU/core ID as it no longer is in coincidence with the
shared slot/socket ID.
While at it additionally distinguish between CPUs with Fireplane and
JBus interconnects as these also use slightly different sizes for the
JBus/agent/module/target IDs.
- Check the return value of init_heap(). This requires moving it after
cons_probe() so we can panic when appropriate. This should be fine as
the PowerPC OFW loader uses that order for quite some time now.
the 'debugging' section of any HEAD kernel and enable for the mainstream
ones, excluding the embedded architectures.
It may, of course, enabled on a case-by-case basis.
Sponsored by: Sandvine Incorporated
Requested by: emaste
Discussed with: kib
indicating an already initialized lock.
- Check for an empty MSI/MSI-X queue entry before asserting that we have
received a MSI/MSI-X message in order to not panic in case of stray MSI/
MSI-X queue interrupts which may happen in case of using an interrupt
handler rather than a filter.
MFC after: 3 days
For PT_TO_SCE stop that stops the ptraced process upon syscall entry,
syscall arguments are collected before ptracestop() is called. As a
consequence, debugger cannot modify syscall or its arguments.
In syscall(), reread syscall number and arguments after ptracestop(),
if debugger modified anything in the process environment. Since procfs
stopevent requires number of syscall arguments in p_xstat, this cannot
be solved by moving stop/trace point before argument fetching.
Move the code to read arguments into separate function
fetch_syscall_args() to avoid code duplication. Note that ktrace point
for modified syscall is intentionally recorded twice, once with original
arguments, and second time with the arguments set by debugger.
PT_TO_SCX stop is executed after cpu_syscall_set_retval() already.
Reviewed by: kib
device in the table based on the count rather than the maxcount.
Also the previous code didn't work properly as it would have been
necessary to reserve the entire maxcount range in order keep later
requests from filling the spare MSIs between count and maxcount,
which would be complicated to unreserve in fire_release_msi().
- For MSIs with filters rather than handlers only don't clear the
event queue interrupt via fire_intr_clear() since given that these
are executed directly would clear it while we're still processing
the event queue, which in turn would lead to lost MSIs.
- Save one level of indentation in fire_setup_intr().
- Correct a bug in fire_teardown_intr() which prevented it from
correctly restoring the MSI in the resource, causing allocation of
a resource representing an MSI to fail after the first pass when
repeatedly loading and unloading a driver module.
sys/conf/makeLINT.mk to only do certain things for certain
architectures.
Note that neither arm nor mips have the Makefile there, thus
essentially not (yet) supporting LINT. This would enable them
do add special treatment to sys/conf/makeLINT.mk as well chosing
one of the many configurations as LINT.
This is a hack of doing this and keeping it in a separate commit
will allow us to more easily identify and back it out.
Discussed on/with: arch, jhb (as part of the LINT-VIMAGE thread)
MFC after: 1 month
the associated debugging under bootverbose.
- Remove freebsd4_sigreturn(); given that FreeBSD 4 didn't supported
sparc64 this only ever served as a transition aid prior to FreeBSD
5.0 and is unused by default since COMPAT_FREEBSD4 was removed from
GENERIC in r143072 nearly 5 years ago.
work.
- Sanity check the parameters passed to the implementations of the
pcib_{read,write}_config() methods. Using illegal values can cause
no real harm but it doesn't hurt to avoid unnecessary data error
traps requiring to flush and re-enable the level 1 caches.
the Sun Fire V215/V245 and Sun Ultra 25/45 machines. This driver also
already includes all the code to support the `Oberon' Uranus to PCIe
bridges found in the Fujitsu-Siemens based Mx000 machines but due to
lack of access to such a system for testing, probing of these bridges
is currently disabled.
Unfortunately, the event queue mechanism of these bridges for MSIs/
MSI-Xs matches our current MD and MI interrupt frameworks like square
pegs fit into round holes so for now we are generous and use one event
queue per MSI, which limits us to 35 MSIs/MSI-Xs per Host-PCIe-bridge
(we use one event queue for the PCIe error messages). This seems
tolerable as long as most devices just use one MSI/MSI-X anyway.
Adding knowledge about MSIs/MSI-Xs to the MD interrupt code should
allow us to decouple the 1:1 mapping at the cost of no longer being
able to bind MSIs/MSI-Xs to specific CPUs as we currently have no
reliable way to quiesce a device during the transition of its MSIs/
MSI-Xs to another event queue. This would still require the problem
of interrupt storms generated by devices which have no one-shot
behavior or can't/don't mask interrupts while the filter/handler is
executed (like the older PCIe NICs supported by bge(4)) to be solved
though.
Committed from: 26C3
so requests may bubble up to a host-PCI bridge driver.
- Distinguish between PCI and PCIe bridges in the device description
so it's a bit easier to follow what hangs off of what in the dmesg.
Unfortunately we can't also tell PCI and PCI-X apart based on the
information provided in the OFW device tree.
- Add quirk handling for the ALi M5249 found in Fire-based machines
which are used as a PCIe-PCIe bridge there. These are obviously
subtractive decoding as as they have a PCI-ISA bridge on their
secondary side (and likewise don't include the ISA I/O range in
their bridge decode) but don't indicate this via the class code.
Given that this quirk isn't likely to apply to all ALi M5249 and
I have no datasheet for these chips so I could implement a check
using the chip specific bits enabling subtractive decoding this
quirk handling is added to the MD code rather than the MI one.
in intr_execute_handlers(). If we managed to get here without an
associated interrupt controller we have way bigger problems.
While at it predict stray vector interrupts as false as they are
rather unlikely.
- Don't blindly call the clear function of an interrupt controller
when adding a handler in inthand_add() as interrupt controllers
like the one driven by upa(4) are auto-clearing and thus provide
NULL instead.
a bit of a detour we can just iterate through the banks array instead
of having to calculate every offset. This change is inspired by the
powerpc version of this function.
- Add support for the JBus to EBus bridges which hang off of nexus(4).
to PCIe bridges.
- Add support for talking the PROM mappings over to the kernel IOTSB
just like we do with the kernel TSB in order to allow OFW drivers
to continue to work.
- Change some members, parameters and variables to unsigned where
more appropriate.
enable IDE I/O" bit which prevents data access traps with revision
0xc8 in Fire-based machines when pci(4) enables PCIM_CMD_PORTEN.
- Like for sun4v also don't add the PCI side of host-PCIe bridges to
the bus on sun4u as they don't have configuration space implement
there either.
of the interrupt handler in intr_fast() as the handler might clobber
it (no in-tree handler currently does but an upcoming one will).
While at it, tidy the register usage in the interrupt counting code.
and are found in sun4u and sun4v machines based on the Fire ASIC.
- Initialize the configuration space of the PCI to EBus variant the
same way as OpenSolaris does.
- Change INTMAP_VEC() to take an INO as its second argument rather
than an INR. The former is what I actually intended with this
macro and how it's currently used.
is that the JBus to EBus bridges share the interrupt controller of a
sibling JBus to PCIe bridge (at least as far as the OFW device tree
is concerned, in reality they are part of the same chip) so we have to
probe and attach the latter first. That happens to be also the case
due to the fact that the JBus to PCIe bridges appear first in the OFW
device tree but it doesn't hurt to ensure the right order.
to the set actually restored by tl0_ret() instead of using the whole
trapframe. Additionally skip %g7 as that register is used as the
userland TLS pointer.
PR: 140523
MFC after: 1 week
while in kernel mode, and later changing signal mask to block the
signal, was fixed for sigprocmask(2) and ptread_exit(3). The same race
exists for sigreturn(2), setcontext(2) and swapcontext(2) syscalls.
Use kern_sigprocmask() instead of direct manipulation of td_sigmask to
reschedule newly blocked signals, closing the race.
Reviewed by: davidxu
Tested by: pho
MFC after: 1 month
the memory or D-cache, depending on the semantics of the platform.
vm_sync_icache() is basically a wrapper around pmap_sync_icache(),
that translates the vm_map_t argumument to pmap_t.
o Introduce pmap_sync_icache() to all PMAP implementation. For powerpc
it replaces the pmap_page_executable() function, added to solve
the I-cache problem in uiomove_fromphys().
o In proc_rwmem() call vm_sync_icache() when writing to a page that
has execute permissions. This assures that when breakpoints are
written, the I-cache will be coherent and the process will actually
hit the breakpoint.
o This also fixes the Book-E PMAP implementation that was missing
necessary locking while trying to deal with the I-cache coherency
in pmap_enter() (read: mmu_booke_enter_locked).
The key property of this change is that the I-cache is made coherent
*after* writes have been done. Doing it in the PMAP layer when adding
or changing a mapping means that the I-cache is made coherent *before*
any writes happen. The difference is key when the I-cache prefetches.
compiled to use the Medium/Low code model, which we currently default
to for the userland. GNU/Linux has moved their default to Medium/Middle
some time ago, which probably explains why the current GNU ld(1) uses
a base in the range between 32 and 44 bits instead.
Submitted by: kib
by looking at the bases used for non-relocatable executables by gnu ld(1),
and adjusting it slightly.
Discussed with: bz
Reviewed by: kan
Tested by: bz (i386, amd64), bsam (linux)
MFC after: some time
first and the native ia32 compat as middle (before other things).
o(ld)brandinfo as well as third party like linux, kfreebsd, etc.
stays on SI_ORDER_ANY coming last.
The reason for this is only to make sure that even in case we would
overflow the MAX_BRANDS sized array, the native FreeBSD brandinfo
would still be there and the system would be operational.
Reviewed by: kib
MFC after: 1 month
OFW device tree for PCI bridges and add a new one for PCI Express.
While at it, take advantage of the former for the rman(9) work-
around in jbusppm(4).
has proven to have a good effect when entering KDB by using a NMI,
but it completely violates all the good rules about interrupts
disabled while holding a spinlock in other occasions. This can be the
cause of deadlocks on events where a normal IPI_STOP is expected.
* Adds an new IPI called IPI_STOP_HARD on all the supported architectures.
This IPI is responsible for sending a stop message among CPUs using a
privileged channel when disponible. In other cases it just does match a
normal IPI_STOP.
Right now the IPI_STOP_HARD functionality uses a NMI on ia32 and amd64
architectures, while on the other has a normal IPI_STOP effect. It is
responsibility of maintainers to eventually implement an hard stop
when necessary and possible.
* Use the new IPI facility in order to implement a new userend SMP kernel
function called stop_cpus_hard(). That is specular to stop_cpu() but
it does use the privileged channel for the stopping facility.
* Let KDB use the newly introduced function stop_cpus_hard() and leave
stop_cpus() for all the other cases
* Disable interrupts on CPU0 when starting the process of APs suspension.
* Style cleanup and comments adding
This patch should fix the reboot/shutdown deadlocks many users are
constantly reporting on mailing lists.
Please don't forget to update your config file with the STOP_NMI
option removal
Reviewed by: jhb
Tested by: pho, bz, rink
Approved by: re (kib)
a device pager (OBJT_DEVICE) object in that it uses fictitious pages to
provide aliases to other memory addresses. The primary difference is that
it uses an sglist(9) to determine the physical addresses for a given offset
into the object instead of invoking the d_mmap() method in a device driver.
Reviewed by: alc
Approved by: re (kensmith)
MFC after: 2 weeks
actually specify valid bases that should be treated just as normal.
The PCI specifications have no indication that 0 would be a magic value
indicating a disabled BAR as commonly used on at least amd64 and i386
but not sparc64. It's unclear what to do in pci_delete_resource()
instead of writing 0 to a BAR though as there's no (other) way do
disable individual BARs so its decoding is left enabled in case of
__PCI_BAR_ZERO_VALID for now.
Approved by: re (kib), jhb
MFC after: 1 week
dependent memory attributes:
Rename vm_cache_mode_t to vm_memattr_t. The new name reflects the
fact that there are machine-dependent memory attributes that have
nothing to do with controlling the cache's behavior.
Introduce vm_object_set_memattr() for setting the default memory
attributes that will be given to an object's pages.
Introduce and use pmap_page_{get,set}_memattr() for getting and
setting a page's machine-dependent memory attributes. Add full
support for these functions on amd64 and i386 and stubs for them on
the other architectures. The function pmap_page_set_memattr() is also
responsible for any other machine-dependent aspects of changing a
page's memory attributes, such as flushing the cache or updating the
direct map. The uses include kmem_alloc_contig(), vm_page_alloc(),
and the device pager:
kmem_alloc_contig() can now be used to allocate kernel memory with
non-default memory attributes on amd64 and i386.
vm_page_alloc() and the device pager will set the memory attributes
for the real or fictitious page according to the object's default
memory attributes.
Update the various pmap functions on amd64 and i386 that map pages to
incorporate each page's memory attributes in the mapping.
Notes: (1) Inherent to this design are safety features that prevent
the specification of inconsistent memory attributes by different
mappings on amd64 and i386. In addition, the device pager provides a
warning when a device driver creates a fictitious page with memory
attributes that are inconsistent with the real page that the
fictitious page is an alias for. (2) Storing the machine-dependent
memory attributes for amd64 and i386 as a dedicated "int" in "struct
md_page" represents a compromise between space efficiency and the ease
of MFCing these changes to RELENG_7.
In collaboration with: jhb
Approved by: re (kib)
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.
Authentication and encryption are not implemented.
There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).
A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.
Drivers that support mesh networks right now are: ath, ral and mwl.
More information at: http://wiki.freebsd.org/WifiMesh
Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.
Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.
Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s
o add to platforms where it was missing (arm, i386, powerpc, sparc64, sun4v)
o define as "1" on amd64 and i386 where there is no restriction
o make the type returned consistent with ALIGN
o remove _ALIGNED_POINTER
o make associated comments consistent
Reviewed by: bde, imp, marcel
Approved by: re (kensmith)
More applications (including Firefox) seem to depend on this nowadays,
so not having this enabled by default is a bad idea.
Proposed by: miwi
Patch by: Florian Smeets <flo kasimir com>
Approved by: re (kib)
used kernel TLB slots when unloading the kernel or modules, which
results in havoc when loading a kernel and modules which take up
less TLB slots afterwards as the unused but locked ones aren't
accounted for in virtual_avail. Eventually this should be fixed
in the loader which isn't straight forward though and the kernel
should be robust against this anyway. [1]
- Ensure that the addresses allocated directly from phys_avail[] by
pmap_bootstrap_alloc() are always colored properly. This implicit
assumption was broken in r194784 as unlike the other consumers the
DPCPU area allocated for the BSP isn't a multiple of PAGE_SIZE *
DCACHE_COLORS. [2]
- Remove the no longer used global msgbuf_phys.
- Remove the redundant ekva parameter of pmap_bootstrap_alloc().
- Correct some outdated function names in ktr(9) invocations.
Requested by: jhb [1]
Reported by: gavin [2]
Approved by: re (kib)
MFC after: 2 weeks
required by video card drivers. Specifically, this change introduces
vm_cache_mode_t with an appropriate VM_CACHE_DEFAULT definition on all
architectures. In addition, this changes adds a vm_cache_mode_t parameter
to kmem_alloc_contig() and vm_phys_alloc_contig(). These will be the
interfaces for allocating mapped kernel memory and physical memory,
respectively, with non-default cache modes.
In collaboration with: jhb
- r187144: Add a reference to the config(5) manpage and
to the "env" kernel config option.
- Add/enable the default USB drivers. Originally the USB
controller and keyboard drivers were disabled as these
interacted badly with the Open Firmware console driver,
i.e. caused the keyboard to not work with ofw_console(4).
Even when switch to uart(4) and the frame buffer drivers
most of the USB drivers still were kept disabled as
several of them, amongst others all of the drivers for
USB Ethernet controllers, weren't endian clean. With the
new USB stack these problem should be gone now so there's
no longer a reason to not include the same set of USB
drivers amd64 does.
o Remove the commented out device ofw_console; apart from it
being currently broken by some TTY changes one really needs
to know how to actually enable and make it work correctly.
entries allocated for translations in pmap_init() as MAP_NOFAULT. This
prevents vm_map_insert from trying to account the entries for swap
usage, that is both wrong and too early to work.
While there, change FALSE to VMFS_NO_SPACE.
Reported and tested by: Florian Smeets <flo at kasimir com>
Reviewed by: marius
- Modules and kernel code alike may use DPCPU_DEFINE(),
DPCPU_GET(), DPCPU_SET(), etc. akin to the statically defined
PCPU_*. Requires only one extra instruction more than PCPU_* and is
virtually the same as __thread for builtin and much faster for shared
objects. DPCPU variables can be initialized when defined.
- Modules are supported by relocating the module's per-cpu linker set
over space reserved in the kernel. Modules may fail to load if there
is insufficient space available.
- Track space available for modules with a one-off extent allocator.
Free may block for memory to allocate space for an extent.
Reviewed by: jhb, rwatson, kan, sam, grehan, marius, marcel, stas
DP83065 Saturn Gigabit Ethernet controllers. These are the successors
of the Sun GEM controllers and still have a similar but extended transmit
logic. As such this driver is based on gem(4).
Thanks to marcel@ for providing a Sun Quad GigaSwift Ethernet UTP (QGE)
card which was vital for getting this driver to work on architectures
not using Open Firmware.
Approved by: re (kib)
MFC after: 2 weeks
goal of shipping 8.0 with MAC support in the default kernel. No policies
will be compiled in or enabled by default, but it will now be possible to
load them at boot or runtime without a kernel recompile.
While the framework is not believed to impose measurable overhead when no
policies are loaded (a result of optimization over the past few months in
HEAD), we'll continue to benchmark and optimize as the release approaches.
Please keep an eye out for performance or functionality regressions that
could be a result of this change.
Approved by: re (kensmith)
Obtained from: TrustedBSD Project
The system hostname is now stored in prison0, and the global variable
"hostname" has been removed, as has the hostname_mtx mutex. Jails may
have their own host information, or they may inherit it from the
parent/system. The proper way to read the hostname is via
getcredhostname(), which will copy either the hostname associated with
the passed cred, or the system hostname if you pass NULL. The system
hostname can still be accessed directly (and without locking) at
prison0.pr_host, but that should be avoided where possible.
The "similar information" referred to is domainname, hostid, and
hostuuid, which have also become prison parameters and had their
associated global variables removed.
Approved by: bz (mentor)
possible future I-cache coherency operation can succeed. On ARM
for example the L1 cache can be (is) virtually mapped, which
means that any I/O that uses temporary mappings will not see the
I-cache made coherent. On ia64 a similar behaviour has been
observed. By flushing the D-cache, execution of binaries backed
by md(4) and/or NFS work reliably.
For Book-E (powerpc), execution over NFS exhibits SIGILL once in
a while as well, though cpu_flush_dcache() hasn't been implemented
yet.
Doing an explicit D-cache flush as part of the non-DMA based I/O
read operation eliminates the need to do it as part of the
I-cache coherency operation itself and as such avoids pessimizing
the DMA-based I/O read operations for which D-cache are already
flushed/invalidated. It also allows future optimizations whereby
the bcopy() followed by the D-cache flush can be integrated in a
single operation, which could be implemented using on-chips DMA
engines, by-passing the D-cache altogether.
directly in cpu_reset() in order to idle the APs before exiting
the kernel and letting the BSP enter the firmware so that processes
like init(8) which still might be running on an AP at that point
don't cause a panic there when it crashes due to the fact it no
longer can be supported by the kernel.
MFC after: 3 days
a fair number of static data structures, making this an unlikely
option to try to change without also changing source code. [1]
Change default cache line size on ia64, sparc64, and sun4v to 128
bytes, as this was what rtld-elf was already using on those
platforms. [2]
Suggested by: bde [1], jhb [2]
MFC after: 2 weeks
CACHE_LINE_SIZE constant. These constants are intended to
over-estimate the cache line size, and be used at compile-time
when a run-time tuning alternative isn't appropriate or
available.
Defaults for all architectures are 64 bytes, except powerpc
where it is 128 bytes (used on G5 systems).
MFC after: 2 weeks
Discussed on: arch@
1) Move the new field (brand_note) to the end of the Brandinfo structure.
2) Add a new flag BI_BRAND_NOTE that indicates that the brand_note pointer
is valid.
3) Use the brand_note field if the flag BI_BRAND_NOTE is set and as old
modules won't have the flag set, so the new field brand_note would be
ignored.
Suggested by: jhb
Reviewed by: jhb
Approved by: kib (mentor)
MFC after: 6 days
supported burst sizes.
- Add support for 64-bit burst sizes (required for SBus GEM).
- Failing to register as interrupt controller during attach shouldn't
be fatal so just inform about this instead of panicing.
- Take advantage of KOBJMETHOD_END.
- Remove some redundant variables.
- Add missing const.
- Failing to register as interrupt controller during attach shouldn't
be fatal so just inform about this instead of panicing.
- Disable rerun of the streaming cache as workaround for a silicon bug
of certain Psycho versions.
- Remove the comment regarding lack of newbus'ified bus_dma(9) as being
able to associate a DMA tag with a device would allow to implement
CDMA flushing/syncing in bus_dmamap_sync(9) but that would totally
kill performance. Given that for devices not behind a PCI-PCI bridge
the host-to-PCI bridges also only do CDMA flushing/syncing based on
interrupts there's no additional disadvantage for polling(4) callbacks
in the case schizo(4) has to do the CDMA flushing/syncing but rather a
general problem.
- Don't panic if the power failure, power management or over-temperature
interrupts doesn't exist as these aren't mandatory and not available
with all controllers (not even Psychos). [1]
- Take advantage of KOBJMETHOD_END.
- Remove some redundant variables.
- Add missing const.
PR: 131371 [1]
- Hook up the streaming buffer (not used by iommu(4) by default, yet)
if available and usable. [1]
- Move the message regarding belated registration as interrupt control
under bootverbose as this isn't something the user should worry about.
Tested by: Michael Moll [1]
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
to the full path of the image that is being executed.
Increase AT_COUNT.
Remove no longer true comment about types used in Linux ELF binaries,
listed types contain FreeBSD-specific entries.
Reviewed by: kan
".note.ABI-tag" section.
The search order of a brand is changed, now first of all the
".note.ABI-tag" is looked through.
Move code which fetch osreldate for ELF binary to check_note() handler.
PR: 118473
Approved by: kib (mentor)
kernel one as the non-faulting flush address in the loader so
we can can change KERNBASE and VM_MIN_KERNEL_ADDRESS if we
ever want to without needing to worry about using a compatible
loader.
- Correctly check for LOADER_DEBUG.
- Add a missing const for page_sizes[].
whole KVA space using one locked 4MB dTLB entry per GB of physical
memory. On Cheetah-class machines only the dt16 can hold locked
entries though, which would be completely consumed for the kernel
TSB on machines with >= 16GB. Therefore limit the KVA space to use
no more than half of the lockable dTLB slots, given that we need
them also for other things.
- Add sanity checks which ensure that we don't exhaust the (lockable)
TLB slots.
firmware versions which wedge when using the OFW test service,
so given that we don't really depend on SUNW,stop-self just nuke
it altogether instead of risking problems.
- At least Fire V880 have a small hardware glitch which causes the
reception of IDR_NACKs for CPUs we actually haven't tried to send
an IPI to, even not as part of the initial try. According to tests
this apparently can be safely ignored though, so just return if
checking for the individual IDR_NACKs indicates no outstanding
dispatch. Serializing the sending of IPIs between MD and MI code
by the combined usage of smp_ipi_mtx makes no difference to this
phenomenon. [1]
- Provide relevant debugging bits already with the initial panic
in case of problems with the IPI dispatch, which would have
allowed to diagnose the above problem without a specially built
kernel.
- In case of cheetah_ipi_selected() base the delay we wait for
other CPUs which also might want to dispatch IPIs on the total
amount of CPUs instead of just the number of CPUs we let this
CPU send IPIs to because in the worst case all CPUs also want
to IPI us at the same time.
Reported and access for extensive tests provided by: Beat Gaetzi [1]
of OFW access semantics, in order to allow future support for real-mode
OF access and flattened device frees. OF client interface modules are
implemented using KOBJ, in a similar way to the PPC PMAP modules.
Because we need Open Firmware to be available before mutexes can be used on
sparc64, changes are also included to allow KOBJ to be used very early in
the boot process by only using the mutex once we know it has been initialized.
Reviewed by: marius, grehan
be fatal so just inform about this instead of panicing.
- Ensure we use the right softc in case the interrupt of a child is
is routed to the companion PBM instead. This hasn't been seen in the
wild so far but given that it's the case for the Schizo interrupts,
handling this situation also for child interrupts as a precaution
seemed a good idea.
- Deal with broken firmware versions which miss child entries in the
ino-bitmap as seen on V880 by belatedly registering as interrupt
controller in schizo_setup_intr(). [1]
- Add missing '\n' when printing the warning regarding Schizo Errata
I-13.
Reported and tested by: Beat Gaetzi [1]
the code for parsing interrupt maps) to PowerPC and reflect their new MI
status by moving them to the shared dev/ofw directory.
This commit also modifies the OFW PCI enumeration procedure on PowerPC to
allow the bus to find non-firmware-enumerated devices that Apple likes to add,
and adds some useful Open Firmware properties (compat and name) to the pnpinfo
string of children on OFW SBus, EBus, PCI, and MacIO links. Because of the
change to PCI enumeration on PowerPC, X has started working again on PPC
machines with Grackle hostbridges.
Reviewed by: marius
Obtained from: sparc64
Sgtty is a programming interface that has been replaced by termios over
the years. In June we already removed <sgtty.h>, which exposes the
ioctl()'s that are implemented by this interface. The importance of this
flag is overrated right now.
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
of the ABI of the currently executing image. Change some places to test
the flags instead of explicit comparing with address of known sysentvec
structures to determine ABI features.
Discussed with: dchagin, imp, jhb, peter
and ifnet functions
- add memory barriers to <machine/atomic.h>
- update drivers to only conditionally define their own
- add lockless producer / consumer ring buffer
- remove ring buffer implementation from cxgb and update its callers
- add if_transmit(struct ifnet *ifp, struct mbuf *m) to ifnet to
allow drivers to efficiently manage multiple hardware queues
(i.e. not serialize all packets through one ifq)
- expose if_qflush to allow drivers to flush any driver managed queues
This work was supported by Bitgravity Inc. and Chelsio Inc.
and XMITS has to be basically done in the same manner as for
the Sabres, i.e. only for devices behind PCI-PCI-bridges and
after a PIO read on the far side of the farest PCI-PCI-bridge.
Given that the Tomatillo documentation mentions no difference
to the Schizo bridges in this regard and this is also still
part of the procedure described Schizo documentation this
seems about right so adjust accordingly (the unconditional
CDMA flushing/syncing previously done was based on how Linux
behaves).
- Implement CDMA flushing/syncing for Schizo version >= 5,
which requires the workaround described in Schizo Errata I-23.
According to Schizo Errata I-13 it's just unusable with
version < 5 though. [1]
- Don't register the Schizo streaming buffer for now until it's
usage is sorted out according to the erratas.
- Register our interrupt filters with the revived INTR_FAST so
they these interrupts can even interrupt filters of device
drivers as necessary.
- Remove the comment regarding lack of newbus'ified bus_dma(9)
as being able to associate a DMA tag with a device would
allow to implement CDMA flushing/syncing in bus_dmamap_sync(9)
but that would totally kill performance. Given that for devices
not behind a PCI-PCI bridge the host-to-PCI bridges also only
do CDMA flushing/syncing based on interrupts there's no
additional disadvantage for polling(4) callbacks in the case
schizo(4) has to do the CDMA flushing/syncing but rather a
general problem.
Reported by: Michael Moll [1]
filters instead of PIL_FAST and allow special filters and handlers
for interrupts which need to be able to interrupt even filters, f.e.
bus error interrupts, to be registered with the revived INTR_FAST
at PIL_FAST.
rerun of the streaming cache for silicon bug workarounds.
- Announce the presence of a streaming cache on attach for
informational purposes.
- For performance reasons don't do unnecessary flushes of the
streaming cache when coherent mappings are synced.
- Fix some minor style issues.
class CPUs. In theory one could also use versions additionally
taking advantage of the prefetch cache with cheetah-class CPUs,
in my worldstone runs these either didn't provide extra speedup
(USIII+) in comparison to the existing spitfire versions or were
even slightly slower (USIIIi) though, so they aren't committed
for now.
The basic problem leading to the VIS-based copy/zero functions
being initially disabled for cheetah-class CPUs was solved by
letting cheetah_init() clear DCR_IFPOE.
while doing the block store workaround so we restore the correct
floating-point registers state in case of nested floating-point
operations resulting from nested interrupts. This allows the
VIS-based block copy/zero functions to be used on machines
requiring this workaround. Alternatively, we could take care of
saving the floating-point registers here, which would be more
inefficiently though and also involves turning off interrupts.
- It turns out that the SCZ_PCI_DMA_SYNC register doesn't work
like the TOMXMS_PCI_DMA_SYNC_PEND one (but more like the
corresponding register in of Hummingbird and Sabre bridges)
and writing the INO of the respective device to it causes a
Safari bus error. However, due to the Schizo errata I-23,
SCZ_PCI_DMA_SYNC can't be used as intended either, so remove
consistent DMA syncing for Schzio bridges for now, which means
that add-on cards with non-"sun4u compliant" (whatever that
means exactly) PCI-PCI-bridges should be avoided until the
proper workaround is implemented. [1]
Reported by: Michael Moll [1]
