boundaries. For good measure, align all other objects to cache
lines boundaries.
Use the new arch_loadseg I/F to keep track of kernel text and
data so that we can wire as much of it as is possible. It is
the responsibility of the kernel to link critical (read IVT
related) code and data at the front of the respective segment
so that it's covered by TRs before the kernel has a chance to
add more translations.
Use a better way of determining whether we're loading a legacy
kernel or not. We can't check for the presence of the PBVM page
table, because we may have unloaded that kernel and loaded an
older (legacy) kernel after that. Simply use the latest load
address for it.
Add support for Pre-Boot Virtual Memory (PBVM) to the loader.
PBVM allows us to link the kernel at a fixed virtual address without
having to make any assumptions about the physical memory layout. On
the SGI Altix 350 for example, there's no usuable physical memory
below 192GB. Also, the PBVM allows us to control better where we're
going to physically load the kernel and its modules so that we can
make sure we load the kernel in memory that's close to the BSP.
The PBVM is managed by a simple page table. The minimum size of the
page table is 4KB (EFI page size) and the maximum is currently set
to 1MB. A page in the PBVM is 64KB, as that's the maximum alignment
one can specify in a linker script. The bottom line is that PBVM is
between 64KB and 8GB in size.
The loader maps the PBVM page table at a fixed virtual address and
using a single translations. The PBVM itself is also mapped using a
single translation for a maximum of 32MB.
While here, increase the heap in the EFI loader from 512KB to 2MB
and set the stage for supporting relocatable modules.
x86 CPU support, better support for powerpc64, some new directives, and
many other things. Bump __FreeBSD_version, and add a note to UPDATING.
Thanks to the many people that have helped to test this.
Obtained from: projects/binutils-2.17
to move the .IA_64.unwind and .IA_64.unwind_info input sections into
separate output sections.
Otherwise ld will complain about it (".data has both ordered
[`.IA_64.unwind'] and unordered [`.IA_64.unwind_info'] sections").
This makes ia64 buildworld run to full completion.
as this only allows us to access file systems that EFI knows about.
With a loader that can only use EFI-supported file systems, we're
forced to put /boot on the EFI system partition. This is suboptimal
in the following ways:
1. With /boot a symlink to /efi/boot, mergemaster complains about
the mismatch and there's no quick solution.
2. The EFI loader can only boot a single version of FreeBSD. There's
no way to install multiple versions of FreeBSD and select one
at the loader prompt.
3. ZFS maintains /boot/zfs/zpool.cache and with /boot a symlink we
end up with the file on a MSDOS file system. ZFS does not have
proper handling of file systems that are under Giant.
Implement a disk device based on the block I/O protocol instead and
pull in file system code from libstand. The disk devices are really
the partitions that EFI knows about.
This change is backward compatible.
MFC after: 1 week
- It is opt-out for now so as to give it maximum testing, but it may be
turned opt-in for stable branches depending on the consensus. You
can turn it off with WITHOUT_SSP.
- WITHOUT_SSP was previously used to disable the build of GNU libssp.
It is harmless to steal the knob as SSP symbols have been provided
by libc for a long time, GNU libssp should not have been much used.
- SSP is disabled in a few corners such as system bootstrap programs
(sys/boot), process bootstrap code (rtld, csu) and SSP symbols themselves.
- It should be safe to use -fstack-protector-all to build world, however
libc will be automatically downgraded to -fstack-protector because it
breaks rtld otherwise.
- This option is unavailable on ia64.
Enable GCC stack protection (aka Propolice) for kernel:
- It is opt-out for now so as to give it maximum testing.
- Do not compile your kernel with -fstack-protector-all, it won't work.
Submitted by: Jeremie Le Hen <jeremie@le-hen.org>
speculative loads. This at least makes control speculative loads
work. In the future we should analyze which faults/exceptions
we want to handle rather than defer to avoid having to call the
recovery code when it's not strictly necessary.
1. Make libefi portable by removing ia64 specific code and build
it on i386 and amd64 by default to prevent regressions. These
changes include fixes and improvements over previous code to
establish or improve APIs where none existed or when the amount
of kluging was unacceptably high.
2. Increase the amount of sharing between the efi and ski loaders
to improve maintainability of the loaders and simplify making
changes to the loader-kernel handshaking in the future.
The version of the efi and ski loaders are now both changed to 1.2
as user visible improvements and changes have been made.
device (kind) specific unit field to the common field. This change
allows a future version of libefi to work without requiring anything
more than what is defined in struct devdesc and as such makes it
possible to compile said version of libefi for different platforms
without requiring that those platforms have identical derivatives
of struct devdesc.
changing the Makefile, fail the creation of loader.efi when there are
unresolved symbols in loader.sym. This avoids silently creating a
faulty EFI binary.
use <machine/efi.h> for the necessary definitions. This makes the EFI
code in sys/boot/efi totally unused, except for pure EFI loaders. As
such, maintenance and porting (to IA-32) of the EFI code is made as easy
as possible.
we construct the EFI image. It doesn't seem to actually end up
in the EFI image, AFAICT.
o Replace .quad, .long and .short with data8, data4 and data2 resp.
The former are gnuisms.
o Redefine _start_plabel as a data16 with @iplt(_start) as its
value. This is the preferred way to create user PLT entries.
binutils 2.15. The linker now creates a .rela.dyn section for
dynamic relocations, while our script created a .rela section.
Likewise, we copied the .rela section to the EFI image, but not
the .rela.dyn section. The fix is to rename .rela to .rela.dyn
in the linker script so that all relocations end up in the same
section again. This we copy into the EFI image.
