Add auto-termination support as well as support for setting the high byte
termination. Booting with '-v' will display the settings that the driver
chose. If you stick narrow devices onto the external wide port, you had
better make sure that your converter cable terminates the bus, you have a
wide device on there that terminates the bus, or you manually set the
termination properly in SCSI-Select instead of using "Automatic". The
code will get the setting right regardless if you *don't* have internal
wide devices in this type of configuration. Unfortunatly this is a limitation
of the design of the Adaptec cards.
Style nit. Backslashes in macro weren't aligned.
aic7xxx.c:
Preserve the value of STPWEN in SXFRCTL1 during initialization. STPWEN
controls low byte termination and is setup by the PCI probe front end.
SDONE, not HDONE.
In the data phase dma handler, mask off just the enable bits instead of
clearing the whole register. Clearing the direction bit could be bad.
Also don't stop a DMA until MREQPEND goes false. Doing this may cause
an ABORT on the PCI bus although I have yet to see this happen.
Add definitions for MREQPEND and the BRDCTL register. The BRDCTL register
is used to handle high byte termination and automatic termination testing.
Disabling npx0 works right now.
Don't reference `npxdriver' if npx0 is not configured. Not configuring
npx0 doesn't quite work yet.
Don't clear potential non-npx pcb flags in setregs().
should be nearly impossible to overflow the QOUTFIFO (worst case 9 command
have to complete with at least 6 of them requiring paging on an aic7850),
so don't take the additional PIO hit to guard against this condition. If we
don't see our interrupt in time, the system has bigger problems elsewhere.
If this ever does happen, the timeout handler will notice and retry the
command.
Remove the ABORT_TAG sequencer interrupt handler. This condition can't happen
with the new SCB paging scheme.
Fix a few bugs noticed by Dan Eischen <deischen@iworks.InterWorks.org>
that could prevent ULTRA from being negotiated to drives above ID 7 and
also could allow an SCB to be passed to ahc_done twice during error recovery.
Fix a bug notice by Rory Bolt <rory@atBackup.com>. It turns out that a
sequencer reset will actually start the sequencer running regardless of the
state of the pause bit. This could lead to strange problems with loading
the sequencer.
Only enable reselections once the channel and SCSIRATE have been cleared.
Add a pause block around the test busy code in the non-tagged case to simplify
error recovery in the corner case of aborting an SCB that just got started.
Simplify reselection processing by removing the call to initialize_scsiid.
Clear the scsiseq re/select control bits and setup for catching bogus
busfrees earlier in the re/select process.
Improve the automatic PIO code. It turns out that SPIORDY is not a reliable
hardware condition bit, so use REQINIT intstead. Don't rely on PHASEMIS
either since it can take too long to come true. Use a brute force comparison
instead.
Remove some unnecessary overhead in the command complete processing. It
should be nearly impossible to overflow the QOUTFIFO (worst case 9 command
have to complete with at least 6 of them requiring paging on an aic7850),
so don't take the additional PIO hit to guard against this condition. If we
don't see our interrupt in time, the system has bigger problems elsewhere.
If this ever does happen, the timeout handler will notice and retry the
command.
not lazy-fault page table pages. Update the copyout support to take
that into account. This should fix some segfault problems on such
machines.
After a short test period, we'll move this into 2.2.
Submitted by: Stephen McKay <syssgm@devetir.qld.gov.au>
an X seesion. Really stupid error of me, and I've been looking at
this code SO many times. Thanks to Kazutaka YOKOTA for seeing this..
Submitted by: Kazutaka YOKOTA
the page to be unbusy, and it caused some algorithmic problems
as a result. There were some other problems with it also, so
this is a general cleanup of the code.
Submitted by: Douglas Crosher <dtc@scrooge.ee.swin.oz.au> and myself.
one in draw_mouse causes spontanious hangs on my p5-100 when I
move the mouse excessively. Forgot that on the last commit, so
using the mouse or destructive cursor would produce large amounts
of flicker..
now dead sys/pci/if_pdq.c which has been committed about by the same
time i made my tests with Matt's code.
LINT should compile now again.
Well, that's a clear case where ``CVS writer locks'' would certainly
(not) have helped. :-]
to -current.
Thanks goes to Ulrike Nitzsche <ulrike@ifw-dresden.de> for giving me
a chance to test this. Only the PCI driver is tested though.
One final patch will follow in a separate commit. This is so that
everything up to here can be dragged into 2.2, if we decide so.
Reviewed by: joerg
Submitted by: Matt Thomas <matt@3am-software.com>
importing it onto a vendor branch first, in the hope that this will
make future maintenance easier.
The conflicts are (hopefully) unimportant. More commits that actually
bring this into the source tree will follow.
Submitted by: Matt Thomas (thomas@lkg.dec.com)
importing it onto a vendor branch first, in the hope that this will
make future maintenance easier.
The conflicts are (hopefully) unimportant. More commits that actually
bring this into the source tree will follow.
Submitted by: Matt Thomas (thomas@lkg.dec.com)
cur_console is NULL when copy_font() is first called from scinit(). This
is apparently harmless when scinit() is called early from sccninit() -
page 0 is apparently mapped r/w then, and 0->status contains suitable
garbage. However, when there is a serial console, scinit() is first
called from scattach() when the page tables are completely initialized,
so the NULL pointer causes a panic.
Submitted by: bruce
