if all registers are 0xff.
This allows me to run with flags 0xc0ff on my IBM-DMCA-21440 disk, which
gives 5MB/sec sequential read :-)
If you have a laptop, try adding flag 0x4000 to your disk, and tell me if
it makes any difference for you.
can't perform overlapping commands on both of its channels.
To enable the CMD640B work-around, the kernel must be compiled with
"options CMD640". Without that option there should be no difference
in the code produced compared to the previous revision of wd.c.
Submitted by: Wolfgang Helbig <helbig@ba-stuttgart.de>
changes, so don't expect to be able to run the kernel as-is (very well)
without the appropriate Lite/2 userland changes.
The system boots and can mount UFS filesystems.
Untested: ext2fs, msdosfs, NFS
Known problems: Incorrect Berkeley ID strings in some files.
Mount_std mounts will not work until the getfsent
library routine is changed.
Reviewed by: various people
Submitted by: Jeffery Hsu <hsu@freebsd.org>
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
instead of 0 if there is no input.
syscons.c:
Added missing spl locking in sccncheckc(). Return the same value as
sccngetc() would. It is wrong for sccngetc() to return non-ASCII, but
stripping the non-ASCII bits doesn't help.
little more reliably. So far I've received a couple of positive
responses and no objections to these changes.
There are two one-line changes:
- In wdprobe(), when testing the error status of drives, don't
unconditionally decide that there is no controller present if we
read back a value of 0x81 (drive 0 okay, drive 1 failed) twice
in a row. This may be caused by having an ATAPI CD-ROM jumpered
as a master on the controller with no slave.
- In wdgetctlr(), when checking for a status of WDCS_READY, check the
value twice. The first time may be bogus. This stops a phantom wd2
device from being detected when an ATAPI CD-ROM is attached to the
secondary controller alone as a slave. (This can cause installation to
fail when sysinstall attempts to open the phantom device and wedges the
system as a result. This has bitten me a couple of times on some
Gateway 2000 machines.)
Saves about 280 butes of source per driver, 56 bytes in object size
and another 56 bytes moves from data to bss.
No functional change intended nor expected.
GENERIC should be about one k smaller now :-)
wdp_fixedcyl) gives it directly. wdp_removedcyl is "reserved" except
in ancient ATA-1 drafts and shouldn't be added. This fixes PR 1288.
Changed some fields and comments in struct wdparams to match a less-
ancient ATA draft.
Fixed bit number for `rdy' in status string.
Added scsi control devices.
Converted almost everything that I changed to use devfs_add_devswf()
and verbose id macros.
st.c:
Renamed enrst* to erst* since that's what the current name is (enrst
seems to be an old name).
chipset. This does not attempt to do anything special with the timing
on the hope that the BIOS will have done the right thing already. The
actual interface from the wd driver to the new facility is not
implemented yet (this commit being an attempt at prodding someone else
to do it because looking at the wd driver always confuses the h*** out of me).
quite work yet, so the heart of it is disabled.
Added bdev and cdev args to dsopen().
drivers:
Fixed device names, links, minor numbers and modes.
wd.c:
Started actually supporting devfs.
diskslice.h:
Added devfs tokens to structs (currently 576 of them per disk! :-().
subr_diskslice.c:
Create devfs entries in dsopen() and (unsuccessfully) attempt to make
them go away at the right times. DEVFS is #undefed at the start so
that this shouldn't cause problems.
Removed old aliases d_rdwr_t and d_ttycv_t for d_read_t/d_write_t and
d_devtotty_t.
Sorted declarations of switch functions into switch order.
Removed duplicated comments and declarations of nonexistent switch
functions.
most devsw referenced functions are now static, as they are
in the same file as their devsw structure. I've also added DEVFS
support for nearly every device in the system, however
many of the devices have 'incorrect' names under DEVFS
because I couldn't quickly work out the correct naming conventions.
(but devfs won't be coming on line for a month or so anyhow so that doesn't
matter)
If you "OWN" a device which would normally have an entry in /dev
then search for the devfs_add_devsw() entries and munge to make them right..
check out similar devices to see what I might have done in them in you
can't see what's going on..
for a laugh compare conf.c conf.h defore and after... :)
I have not doen DEVFS entries for any DISKSLICE devices yet as that will be
a much more complicated job.. (pass 5 :)
pass 4 will be to make the devsw tables of type (cdevsw * )
rather than (cdevsw)
seems to work here..
complaints to the usual places.. :)
That's EVERY SINGLE driver that has an entry in conf.c..
my next trick will be to define cdevsw[] and bdevsw[]
as empty arrays and remove all those DAMNED defines as well..
Each of these drivers has a SYSINIT linker set entry
that comes in very early.. and asks teh driver to add it's own
entry to the two devsw[] tables.
some slight reworking of the commits from yesterday (added the SYSINIT
stuff and some usually wrong but token DEVFS entries to all these
devices.
BTW does anyone know where the 'ata' entries in conf.c actually reside?
seems we don't actually have a 'ataopen() etc...
If you want to add a new device in conf.c
please make sure I know
so I can keep it up to date too..
as before, this is all dependent on #if defined(JREMOD)
(and #ifdef DEVFS in parts)
totally dynamic.
this is only the devices in i386/isa
I'll do more tomorrow.
they're completely masked by #ifdef JREMOD at this stage...
the eventual aim is that every driver will do a SYSINIT
at startup BEFORE the probes, which will effectively
link it into the devsw tables etc.
If I'd thought about it more I'd have put that in in this set (damn)
The ioconf lines generated by config will also end up in the
device's own scope as well, so ioconf.c will eventually be gutted
the SYSINIT call to the driver will include a phase where the
driver links it's ioconf line into a chain of such. when this phase is done
then the user can modify them with the boot: -c
config menu if he wants, just like now..
config will put the config lines out in the .h file
(e.g. in aha.h will be the addresses for the aha driver to look.)
as I said this is a very small first step..
the aim of THIS set of edits is to not have to edit conf.c at all when
adding a new device.. the tabe will be a simple skeleton..
when this is done, it will allow other changes to be made,
all teh time still having a fully working kernel tree,
but the logical outcome is the complete REMOVAL of the devsw tables.
By the end of this, linked in drivers will be exactly the same as
run-time loaded drivers, except they JUST HAPPEN to already be linked
and present at startup..
the SYSINIT calls will be the equivalent of the "init" call
made to a newly loaded driver in every respect.
For this edit,
each of the files has the following code inserted into it:
obviously, tailored to suit..
----------------------somewhere at the top:
#ifdef JREMOD
#include <sys/conf.h>
#define CDEV_MAJOR 13
#define BDEV_MAJOR 4
static void sd_devsw_install();
#endif /*JREMOD */
---------------------somewhere that's run during bootup: EVENTUALLY a SYSINIT
#ifdef JREMOD
sd_devsw_install();
#endif /*JREMOD*/
-----------------------at the bottom:
#ifdef JREMOD
struct bdevsw sd_bdevsw =
{ sdopen, sdclose, sdstrategy, sdioctl, /*4*/
sddump, sdsize, 0 };
struct cdevsw sd_cdevsw =
{ sdopen, sdclose, rawread, rawwrite, /*13*/
sdioctl, nostop, nullreset, nodevtotty,/* sd */
seltrue, nommap, sdstrategy };
static sd_devsw_installed = 0;
static void sd_devsw_install()
{
dev_t descript;
if( ! sd_devsw_installed ) {
descript = makedev(CDEV_MAJOR,0);
cdevsw_add(&descript,&sd_cdevsw,NULL);
#if defined(BDEV_MAJOR)
descript = makedev(BDEV_MAJOR,0);
bdevsw_add(&descript,&sd_bdevsw,NULL);
#endif /*BDEV_MAJOR*/
sd_devsw_installed = 1;
}
}
#endif /* JREMOD */
Convert the remaining sysctl stuff to the new way of doing things.
the devconf stuff is the reason for the large number of files.
Cleaned up some compiler warnings while I were there.
modularization of the wd/wcd/atapi driver is ugly.
Include cons.h from a less bogus place.
Removed an ARGSUSED. Unused args are normal for devswitch functions
and lint was informed about them for about 5 functions out of 1000.
Lint should be informed about them, if at all, in some other way.
I tried to solve the problem of IDE probing compatibility in this version.
When compiled without an ATAPI option, the wd driver is
fully backward compatible with 2.0.5. With ATAPI option,
the wdprobe becomes strictly weaker. That is, if wdprobe works
without ATAPI option, it will always work with it too.
Another problem was with the CD-ROM drive attached as a slave
in the IDE bus, where there is no master. All IDE CD-ROM
drives are shipped in slave configuration, and most users
just plug them in, never thinking about jumpers.
It works fine with ms-dos and ms-windows, and this
version of the driver supports it as well.
The eject op can now load disks. Just repeat it twice,
and the disk will be ejected and then loaded back.
The disc cannot be ejected if it is mounted.
Submitted by: Serge Vakulenko, <vak@cronyx.ru>
It closed the wrong device (usually the B partition instead of the C
partition).
It closed a device without having opened it.
It didn't open a device often enough. This caused swap partitions on
slices other than the first slice looked at to be unavailable for swapping.
It didn't check the device number sufficiently.
