sys/alpha/conf/GENERIC.
Note: the PNIC ignores the lower few bits of the RX buffer DMA address,
which means we have to add yet another kludge to make it happy. Since
we can't offset the packet data, we copy the first few bytes of the
received data into a separate mbuf with proper alignment. This puts
the IP header where it needs to be to prevent unaligned accesses.
Also modified the PNIC driver to use a non-interrupt driven TX
strategy. This improves performance somewhat on x86/SMP systems where
interrupt delivery doesn't seem to be as fast with an SMP kernel as
with a UP kernel.
if uio->uio_offset != -1. This fixes a problem with aio_read/write
and permits a straightforward implementation of pread/pwrite.
PR: kern/8669
Submitted by: John Plevyak <jplevyak@inktomi.com>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
the IP header (this would not work for bridged packets).
This has been fixed long ago in the 2.2 branch.
Problem noticed by: a few people
Fix suggested by: Remy Nonnenmacher
settings you've just sent them and return random values if you follow
the set by a get. This causes problems when you latter run a Tag-enabled
command when you've command tagged mode off.
kern.chroot_allow_open_directories = 0
chroot(2) fails if there are open directories.
kern.chroot_allow_open_directories = 1 (default)
chroot(2) fails if there are open directories and the process
is subject of a previous chroot(2).
kern.chroot_allow_open_directories = anything else
filedescriptors are not checked. (old behaviour).
I'm very interested in reports about software which breaks when
running with the default setting.
affects cases where there is a slave but no master. These bugs
were usually recovered from provided ATAPI was configured, but only
after lengthy delays. Configuring ATAPI still fixes some bugs for
non-atapi drives.
Don't wait for seek complete in wdreset(). If necessary for pre-ata
drives, it can be waited for later (we got it wrong by only looking
at it for drive 0 anyway). It is set as part of a historical
signature for ata drives but doesn't say anything useful about the
reset state. It is cleared as part of a non-historical signature
for atapi drives so that drivers which don't understand atapi drives
seem to see no drive. Waiting for it caused lengthy delays and
broke the status returned by wdreset() in cases where the master
was not an ata drive. Then the whole wdprobe() failed in some
cases where the recovery code didn't work.
Don't wait for drive ready in wdreset(). The considerations are
the same as for seek complete, except drive ready does say something
useful about the reset state of ata drives, and waiting for it
later is required anyway for such drives.
Lengthy delays can now be avoided by not configuring nonexistent
(ata) drives. Unfortunately, this breaks detection of atapi drives
in some configurations.
Recognize aic7895 controllers that have been "acquired" by a RAIDPort
card as normal aic7895s.
Recognize the aic7815 Raid Parity/Memory controller chip and notify
the user that it's RAID functionality will be ignored.
Don't mess with the IRQMS bit in the host control register unless
we are an aic7770 chip.
Use calling context to determine if the card is already paused when
we update the target message request bit field in controller scratch
ram. Looking at the paused bit in the HCNTRL register opened up a
race condition.
Insert delays in the target message request update routine as a temporary
work around for what looks like a chip bug. I'm still investigating this
one.
Fix the Abort/Abort Tag/BDR handler to pull its message from the message
buffer in our softc instead of attempting to get it from a register on
the controller. The message is never recorded by the controller in the
new message scheme.
Don't rely on having an SCB when a BDR occurs. We can issue these during
invalid reconnects to.
Fix a few cases where we were restarting the sequencer but then still
falling out of a switch statement to unpause the sequencer again.
This could cause us to mess up sequencer state if it generated another
pausing interrupt between the time of the restart and unpause.
Kill the 'transceiver settle' loop during card initialization. I
failed to realize that a controller that is not connected to any
cables will never settle or enable the SCSI transceivers at all.
The correct solution is to monitor the IOERR interrupt which indicates
that the transceiver state has changed (UW<->LVD).
Modify the aic7xxx assembler to properly echo input when stdin is not
a tty.
remove the splbio() around the call to launch read requests.
launch_requests:
Move the splbio() protection outside the entire launch_loop. The
previous location was causing problems with IDE drives, where the
call to the strategy routine often did not complete until after
complete_rqe deallocated the request structure.
Solution-independently-found-by: Russell Neeper <r-neeper@tamu.edu>
Problem-reported-by: Vallo Kallaste <vallo@matti.ee>
John Saunders <john@nlc.net.au>
Bernd Walter <ticso@cicely.de> (maybe)
Check for partition types FS_VINUM and FS_UNUSED. Accept both, but
complain about FS_UNUSED. At a later date, only FS_VINUM will be
accepted.
Threatened-since: over a year
Add a flag `force' (VF_FORCECONFIG) to force name changes of
existing drives.
config_drive:
If the drive already has a vinum label, and name doesn't match the
specified drive, do it anyway if the 'force' flag is specified.
finish_config:
Reset the `force' flag.
Continually-tripped-over-by: Karl Pielorz <kpielorz@tdx.co.uk>
give_sd_to_drive:
If the drive is down, take the subdisk down and don't try to fix
things.
update_plex_config:
Don't try to update the config parameters of a plex which isn't
fully configured (state plex_init or plex_unallocated).
Correctly calculate the amount to trim off a striped or RAID-5 plex
whose size is not a multiple of the stripe size.
/usr/sbin/sysctl -> ${DESTDIR}/sbin/sysctl in some versions of 2.2,
and this link was broken if DESTDIR was set.
Added a SYMLINKS macro. This works the same as LINKS, except it
creates symlinks and the linked-to pathname may be relative. This
is more flexible than LN_FLAGS, since it supports installing
symlinks independently of hard links.
Use `ln -f[s] ...' instead of `rm -f ...; ln [-s] ...' for LINKS and
SYMLINKS. This is equivalent if the target is neither a directory nor
a symlink to a directory.
PR: 8279
Remove more (redundant) map timestamp increments from properly
synchronized routines. (Changed: vm_map_entry_link, vm_map_entry_unlink,
and vm_map_pageable.)
Micro-optimize vm_map_entry_link and vm_map_entry_unlink, eliminating
unnecessary dereferences. At the same time, converted them from macros
to inline functions.
