Commit Graph

22049 Commits

Author SHA1 Message Date
adrian
5641813833 The comment is misleading - that register setting seems to kick off the
initial chip NF cal.
2010-08-15 11:32:05 +00:00
bschmidt
267bcceb3d Introduce IEEE80211_C_RATECTL, drivers which use the ratectl framework
should set this capability.

MFC after:	2 weeks
2010-08-14 20:12:10 +00:00
adrian
a8c5860291 A local addition, not imported from ath9k.
AR_PHY_CALMODE is explicitly reset on interface reset for other chipsets;
this commit also sets it for the AR9160.
2010-08-14 15:48:18 +00:00
adrian
a5baf37074 * Merge in AR9160 initval updates from Linux-2.6.34.
* Grab the AR_PHY_CCA and AR_PHY_EXT_CCA initvals from Linux wireless-testing.

Obtained from: Linux-2.6.34
2010-08-14 15:46:18 +00:00
adrian
0972b395c2 Merge in a fix for the power/(gain?) calculation. Apply it to both
the 5416/9160 and 9285 code paths.

Obtained from:	OpenWRT r22123, 522-ath9k_pwrcal_fix.patch
2010-08-14 15:29:21 +00:00
adrian
4759296b2b Fix the calibration logic to correctly clamp the calculated coefficient.
Obtained from:	OpenWRT r22123, 521-ath9k_iqcal_fix.patch
2010-08-14 15:28:15 +00:00
adrian
03b390ec53 Export ath stats via snmp, rather than requiring a debugging interface
and "athstats".
2010-08-14 14:18:02 +00:00
adrian
92d8dcb652 Add a global counter of missed beacons.
The existing missed beacon count is reset once a beacon isn't missed.
2010-08-14 14:01:12 +00:00
yongari
d05dbde941 Make sure to disable RX MAC in alc_stop_mac(). Previously there
was a logic error which it always enabled RX MAC.
2010-08-13 19:39:33 +00:00
adrian
ab694183de * Fix indentation
* Restore comment erroneously deleted from the previous commit
2010-08-12 08:39:54 +00:00
adrian
fe722c0e3c Loading the NF CCA values may take longer than expected to occur.
If it does, don't then try reprogramming the NF "cap" values (ie
what values are the "maximum" value the NF can be) - instead,
just leave the current CCA value as the NF cap.

This was inspired by some similar work from ath9k. It isn't
a 100% complete solution (as there may be some reason where a
high NF CCA/cap is written, causing the baseband to stop thinking it
is able to transmit, leading to stuck beacon and interface reset)
which I'll investigate and look at fixing in a later commit.

Obtained from:	Linux
2010-08-12 06:20:54 +00:00
adrian
99130e8f4d Use ar5212IsNFCalInProgress() to check for NF calibration progress. 2010-08-12 06:14:26 +00:00
adrian
a62e0b014a Fix indentation. 2010-08-12 06:12:39 +00:00
adrian
85bba21fcd Ensure that the correct rxchainmask is used when doing calibration in the
AR5416 and later chipsets.

ath_hal_calibrateN() calls the HAL calibrateN function with rxchainmask=0x1.
This is not necessarily the case for AR5416 and later chipsets.
2010-08-12 06:11:44 +00:00
adrian
6a989e2e78 Internal NF calibration should not occur in parallel with any other
calibration. Ensure that the NF calibration completes before continuing
with the rest of the calibration setup process.
2010-08-12 06:08:36 +00:00
adrian
2666ce6d51 Add a couple of functions to check NF calibration progress / completion. 2010-08-12 06:06:14 +00:00
takawata
8d948403ba Add tpm(4) driver for Trusted Platform Module.
You may want to look at http://bsssd.sourceforge.net/ .

Submitted by: Hans-Joerg Hoexer <Hans-Joerg_Hoexer@genua.de>
2010-08-12 00:16:18 +00:00
jhb
6ee4bb3af6 Do not use %z to print a time_t. Fixes build on architectures where time_t
and size_t are different types.
2010-08-11 16:56:38 +00:00
neel
d7725ba6bb Start using the 'init_static_kenv()' API provided by r198561 to initialize
CFE environment variables.
2010-08-11 02:13:50 +00:00
gavin
243488333f Now that the uplcom(4) driver can autodetect the chipset type, sync the
list of devices supported by uplcom(4) with the following sources:

NetBSD  src/sys/dev/usb/uplcom.c 1.70
OpenBSD src/sys/dev/usb/uplcom.c 1.52
Linux   drivers/usb/serial/pl2303.h from kernel 2.6.35
BeOS    usb_serial/driver.c 1.32

Give several devices better descriptions, and rename
PROLIFIC2 -> NETINDEX while here to match everybody else.

MFC after:	6 weeks (after r211111)
2010-08-10 19:13:11 +00:00
adrian
f6c54fb22e Don't delay updating the longcal timer - instead, update the longcal
flag immediately so it's only set once per longcal interval.

Without this, the current AR5416 code will continuously spam NF
calibrations during a periodic calibration if the longcal flag
is set. The longcal flag wouldn't be cleared until the calibration
method indicates that calibrations are "complete".

This drops the rate of NF calibration updates down from "once every
shortcal" (ie, every 100ms) during a periodic calibration, to only
once per "longcal" interval. Spamming NF calibrations every 100ms
caused some potentially horrific issues in noisy environments as
NF calibrations can take longer than 100ms and this spamming can
cause invalid NF calibration results to be read back - leading to
missed beacons, and thus leading to a stuck beacon situation.

Stuck beacons cause interface resets, which restart calibrations.
This means that the longcal calibration runs every 100ms (shortcal)
until all initial calibrations are completed. This spamming can then
cause the above issues which leads to stuck beacons, leading to
interface resets, etc, etc. Quite annoying.
2010-08-10 07:56:56 +00:00
adrian
45442bf243 Bring over ar5416 inivals from Linux-2.6.34.
Reviewed by:	rpaulo@
Obtained from:	Linux
2010-08-10 07:48:13 +00:00
adrian
e3e58186e8 Re-format the ar5416 inivals to be consistent with what
Linux ath9k uses.
2010-08-10 07:47:43 +00:00
gavin
c11b0f0ec9 Attempt to autodetect the cype of chipset, rather than storing this
within the device table.  This code uses the same algorithm as used in the
Linux, NetBSD and DragonflyBSD driver.

While investigating this, it became apparent that the Linux driver always
initialises the device, and not just in the PL2303HX case.  Change
uplcom(4) to do the same.

This change allows us to synchronize our device ID list with Linux and
NetBSD, without requiring knowledge of the chipset in use.

Reviewed by:	hselasky
MFC after:	6 weeks
2010-08-09 17:42:05 +00:00
yongari
1e453ce0eb Add support for Atheros AR8151/AR8152 PCIe gigabit/fast ethernet
controller. These controllers are known as L1D(AR8151) and
L2CB/B2(AR8152). This change adds supports for the following
controllers.
 o AR8151 v1.0(L1D) gigabit ethernet controller
 o AR8151 v2.0(L1D) gigabit ethernet controller
 o AR8152 v1.1(L2CB) fast ethernet controller
 o AR8152 v2.0(L2CB2) fast ethernet controller
These controllers have the same feature of AR8131/AR8132 and
support improved power saving control. The user visible change at
this moment is reduced jumbo frame size from 9KB to 6KB. Many
thanks to Atheros for continuing to support FreeBSD.

HW donated by:	Atheros Communications, Inc.
2010-08-09 17:28:08 +00:00
gavin
b960bf863a Add entries for some devices I have locally. 2010-08-09 17:27:27 +00:00
yongari
26fe9e04f8 Add F1 PHY found on Atheros AR8151 v2.0 PCIe gigabit ethernet
controller.
2010-08-09 17:22:14 +00:00
des
9f1a6fc5a6 - Add full support for header / data digests.
- Increase target limit from 4 to 64; this limit will be removed entirely
  at a later time.
- Improve recovery from lost network connections.
- Fix some potential deadlocks and a serious memory leak.
- Fix incorrect use of MH_ALIGN (instead of M_ALIGN), which makes no
  practical difference, but triggers a KASSERT with INVARIANTS.
- Fix some warnings in iscontrol(8) and improve the man page somewhat.

Submitted by:	Daniel Braniss <danny@cs.huji.ac.il>
Sponsored by:	Dansk Scanning A/S, Data Robotics Inc.
2010-08-09 12:36:36 +00:00
yongari
f0e5a03c15 It seems some old Sundace(now IC Plus Corp.) controllers do not
like memory mapped register access. Typical problem from the issue
was MII access returned unreliable values. I'm not sure this comes
from lack of register flushing in MII access after accessing
STE_PHYCTL register though.
To address the issue, read hints data that controls which type of
memory mapping should be used in driver. ste(4) still prefers
memory mapping to io mapping but honor hints entered by user except
for controllers that have problems with memory mapping.
The hint to use iomapping could be given by adding the following
line to /boot/device.hints file.

hint.ste.0.prefer_iomap="1"

PR:	kern/149285
MFC after:	5 days
2010-08-09 01:47:09 +00:00
gavin
0ae2b03fe8 The PL2302X can support any baud rate <= 6Mbps, allow any rate to be set.
PR:		usb/128324
Submitted by:	Mike Durian <durian shadetreesoftware.com> (original patch)
MFC after:	2 weeks
2010-08-08 20:53:00 +00:00
yongari
08ccc1c1b2 Cache PCIY_PMG and PCIY_EXPRESS capability pointer to softc and use
it instead of calling pci_find_extcap().
2010-08-08 00:43:41 +00:00
yongari
ae142ea6e9 Remove unnecessary assignment. 2010-08-08 00:23:36 +00:00
yongari
0eb991b7bb Always disable ASPM L0s and enable L1 before entering into WOL
suspend state.  Also disable master clock after PHY power down,
this is supposed to save more power. The master clock should be
enabled if WOL is active.
2010-08-08 00:12:31 +00:00
yongari
b67da7a96f Do not touch CMB TX threshold register when CMB is not used.
Note, alc(4) does not use CMB at all due to silicon bug.
2010-08-07 23:41:46 +00:00
yongari
b1b42e7623 Controller does not seem to support more than 1024 bytes DMA burst.
Limit DMA burst size to be less than or equal to 1024 bytes.
2010-08-07 23:33:06 +00:00
yongari
9533954d59 Marvell model number 0x06 is 88E1101 PHY. 2010-08-07 23:16:21 +00:00
gavin
14181a6158 Sync the list of devices supported by uslcom(4) with NetBSD, Linux, OpenBSD
and BeOS.  The devices supported by uslcom(4) are now in sync with:

NetBSD  src/sys/dev/usb/uslsa.c 1.11
OpenBSD src/sys/dev/usb/uslcom.c 1.20
Linux   source/drivers/usb/serial/cp210x.c from kernel 2.6.35
BeOS    usb_serial/driver.c 1.32

Two vendor/product IDs from Linux have not been added to uslcom(4):
  SILABS SAEL - This device has special code in u3g to support it
  SILABS GSM2228 - I suspect this should also be covered by u3g(4).

MFC after:	1 week
2010-08-07 16:14:40 +00:00
gavin
ca78f6e790 Sort this file a little better: the vendors are supposed to be sorted by
vendor ID in the vendor section, and by symbolic name in the product
section.  Products are sorted by product ID.  While here, get rid of a
duplicate Microsoft Mouse entry, revealed by sorting.

MFC after:	1 week
2010-08-07 16:08:37 +00:00
joel
38858fc544 Fix typo in comment. 2010-08-07 08:31:32 +00:00
jkim
c750c1a108 Protect shared palette and state buffer with a mutex. Remove defunct
spltty() calls while I am here.
2010-08-07 05:46:04 +00:00
jkim
2c643eaad8 When EC burst mode is activated and multiple bytes are accessed, do not
disable and enable repeatedly, just do it once per call.  It also reduces
code duplication.  Check all parameters early and fail immediately.
2010-08-06 23:35:33 +00:00
jkim
68285361e2 Merge ACPICA 20100806. 2010-08-06 23:11:19 +00:00
jfv
6012099d55 Put the early setting of the MAC type back, its
removal resulted in broken code in MSIX setup.
2010-08-06 20:55:49 +00:00
mjacob
57aab8cfc7 Figure which is the IO and MEM bars- do not assume that they are in
a fixed order.

PR:		149220
Obtained from:	John Baldwin
MFC after:	1 month
2010-08-06 17:27:00 +00:00
kib
d1366c1596 Disable sync cache for the Transcend Jetflash V90. It is more specific
quirk over the general one for transcend sticks.

Submitted by:	Mykola Dzham <i levsha me>
MFC after:	1 week
2010-08-06 13:45:16 +00:00
kib
328786e473 Mark /dev/zero and /dev/null as eternal.
In collaboration with:	pho
MFC after:	1 month
2010-08-06 09:47:48 +00:00
yongari
c1b8358998 Reduce Tx interrupt moderation timer from 50ms to 1ms. The default
value resulted in poor performance for UDP packets. With this
change, UDP bulk transfer performance is more than 940Mbps.

While I'm here fix a wrong register definition.
2010-08-06 00:50:16 +00:00
jhb
5cf4f67274 - Retire acpi_pcib_resume(). It is has just been an alias for
bus_generic_resume() since the pci_link(4) driver was added.
- Change the ACPI PCI-PCI bridge driver to inherit most of its methods
  from the generic PCI-PCI bridge driver.  In particular, this will now
  restore PCI config registers for ACPI PCI-PCI bridges.

Tested by:	Oleg Sharoyko  osharoiko of gmail
2010-08-05 16:10:12 +00:00
gavin
924ee386ba Do not free sc if attach failed, as it was allocated by the bus
infrastructure, not us.  This appears to be a leftover from an older
version of the driver.

Submitted by:	avg
Tested by:	Anton Shterenlikht <mexas bristol.ac.uk>
MFC after:	1 week
X-MFC-Note:	To stable/8 and stable/7 only
2010-08-04 07:49:40 +00:00
delphij
d29205b578 Catch known CPUs before using IA32_TEMPERATURE_TARGET.
This way we would have an opportunity to hide the
Tj(target) value doesn't seem right stuff if we know
it's not working there.

Add temperature value for Core2 Duo Extreme Mobile that
I have access to.
2010-08-04 00:25:13 +00:00