Revert r338177, r338176, r338175, r338174, r338172
After long consultations with re@, core members and mmacy, revert
these changes. Followup changes will be made to mark them as
deprecated and prent a message about where to find the up-to-date
driver. Followup commits will be made to make this clear in the
installer. Followup commits to reduce POLA in ways we're still
exploring.
It's anticipated that after the freeze, this will be removed in
13-current (with the residual of the drm2 code copied to
sys/arm/dev/drm2 for the TEGRA port's use w/o the intel or
radeon drivers).
Due to the impending freeze, there was no formal core vote for
this. I've been talking to different core members all day, as well as
Matt Macey and Glen Barber. Nobody is completely happy, all are
grudgingly going along with this. Work is in progress to mitigate
the negative effects as much as possible.
Requested by: re@ (gjb, rgrimes)
If we fail noise floor calibration then we may end up with a deaf NIC
which we can't recover without a full chip reset.
Earlier chips seem to get less stuck in this condition versus AR9280/later
and AR9300/later, but whilst here just fix up the AR5212 era chips to also
return NF calibration failures.
This HAL routine would only return failure if the channel was not configured.
This is a no-op until the driver side code for doing resets and the HAL
code for being told about the reset type (and then handling it!) is
implemented.
Tested:
* AR9280, STA mode
* AR2425, STA mode
* AR9380, STA mode
I'm in the process of reworking how the reset path works with an eye
to better recovery when the chips hang and/or go RF/PHY deaf.
This is the first step in a lot of unification and API changes.
Rename ACPI_IVRS_HARDWARE_NEW to ACPI_IVRS_HARDWARE_EFRSUP, since new definitions add Extended Feature Register support. Use IvrsType to distinguish three types of IVHD - 0x10(legacy), 0x11 and 0x40(with EFR). IVHD 0x40 is also called mixed type since it supports HID device entries.
Fix 2 coverity bugs reported by cem.
Reported by:jkim, cem
Approved by:grehan
Differential Revision://reviews.freebsd.org/D14501
IVRS can have entry of type legacy and non-legacy present at same time for same AMD-Vi device. ivhd driver will ignore legacy if new IVHD type is present as specified in AMD-Vi specification. Earlier both of IVHD entries used and two ivhd devices were created.
Add support for new IVHD type 0x11 and 0x40 in ACPI. Create new struct of type acpi_ivrs_hardware_new for these new type of IVHDs. Legacy type 0x10 will continue to use acpi_ivrs_hardware.
Reviewed by: avg
Approved by: grehan
Differential Revision:https://reviews.freebsd.org/D13160
plain-vanilla ETH microcode. The QOS_VLAN firmware added support in microcode
for handling IEEE 802.1q tags, but the npe(4) driver did not actually
support the relevant signalling. As a result, it was impossible to use
VLANs with npe(4). Switching to the more basic microcode (same license)
removes the on-NIC promisisng and makes vlan(4) work on both NPE interfaces.
Ref: https://lists.freebsd.org/pipermail/freebsd-arm/2012-August/003826.html
It turns out that this is useful on hornet and wasp SoCs but it isn't
enabled in ye olde HAL /unless/ you were using a version from one of the
business units building USB targetted devices. It eventually got fixed
for all of them as people started wanting to use the USB ports on their
SoCs (eg for flash storage, bluetooth, 4G/LTE widgets, etc.)
This is actually a fix from ath9k but I'm merging it with the available-but-
disabled code in the QCA reference HAL.
Tested:
* AR9331 SoC
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
* flesh out a "get default DFS parameters" routine
* remove the stub that returns NULL
* fix up the enable DFS method to do what FreeBSD does - specifically, allow pe_enabled
to be set/cleared.
This allows the radar pulse reporting code to function, but it doesn't yet
do anything useful.
* add debugging
* disable the manual noise floor calibration and tracking done by the HAL;
this interferes with the normal calibration path and will lock up the RX
side
* don't program short report / priority if they're provided as NOVAL.
