The current resolution of the Xen PV clock is too high, which causes an
adjustment of 5s to be applied to it. Reduce the resolution to be the same
as the RTC plus one, so it's always selected as the best source when
available on x86.
Also don't reset the clock on resume, it's pointless and discards any
previous adjustments.
Sponsoted by: Citrix Systems R&D
Dom0 should be able to set the host time. This is implemented by first
writing to the RTC (as would be done on bare metal), and then using the
XENPF_settime64 hypercall in order to force Xen to update the wallclock
shared page of all domains.
Sponsored by: Citrix Systems R&D
This is going to be used by the Xen clock on Dom0 in order to set the RTC of
the host. The current logic in atrtc_settime is moved to atrtc_set and the
unused device_t parameter is removed from the atrtc_set function call so it
can be safely used by other callers.
Sponsored by: Citrix Systems R&D
Reviewed by: kib, jhb
Differential revision: https://reviews.freebsd.org/D6067
With the removal of the usage of the VCPU_SSHOTTMR_future flag, now
all errors from xentimer_vcpu_start_timer should be considered fatal, and
the loop is no longer needed since in case of setting the timer in the past
we will get an event interrupt right away (instead of returning ETIME).
Sponsored by: Citrix Systems R&D
MFC after : 2 weeks
On slow platforms with unreliable TSC, such as QEMU emulated machines,
it is possible for the FreeBSD kernel to request the next event in the
past. In that case, in the current implementation of
xentimer_vcpu_start_timer, we simply return -ETIME. To be precise Xen
returns -ETIME and we pass it on. As a consequence we need to loop
around to function to make sure that the timer is properly set.
Instead it is better to always ask the hypervisor for a timer event,
even if the timeout is past. To do that, remove the VCPU_SSHOTTMR_future
flag.
Submitted by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed by: royger
MFC after: 2 weeks
the monitored directory as the result of rename(2) operation. The
renames staying in the directory are not reported.
Submitted by: Vladimir Kondratyev <wulf@cicgroup.ru>
MFC after: 2 weeks
rename removing or adding subdirectory entry.
Discussed with and tested by: Vladimir Kondratyev <wulf@cicgroup.ru>
NetBSD PR: 48958 (http://gnats.netbsd.org/48958)
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
* break out the operating mode and rx filter into new functions, rather
than them being hard-coded
* if we're in sniffer mode or not associated, set the BSS MAC to all zero,
rather than relying on a chip reset to do it for us
* add comments about .. how interestingly buggy the chip is.
Tested:
* AR9170 + AR9102, STA+monitor mode
Obtained from: linux carl9170 (general chip workings, constant definitions)
Switch to add_channel / add_channel_ht40 + pass channel's TX power
for the last.
Tested by: dhw
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6141
chunk, enable UDP encapsulation for all those addresses.
This helps clients using a userland stack to support multihoming if
they are not behind a NAT.
MFC after: 1 week
This is based on a change from OpenBSD:
"Fix restore so that it can actually restore files larger than 4GB by
changing the type of "size" to off_t in getfiles() plus little dependent
type cleanup, from Daniel Lucq."
It is an important for machines with 32 bit longs.
While here unsign the flags, also from OpenBSD.
Obtained from: OpenBSD (through bitrig, I hate CVS)
MFC after: 2 weeks
The new bcache code does not know the size of the disk, and therefore may attempt to read past the end of the disk while trying to fill its read-ahead cache.
This is usually not an issue, it fails gracefully on all of my machines, but some BIOSes seem to retry the reads for up to 30 seconds each, resulting in a long stall during boot
Submitted by: Toomas Soome <tsoome@me.com>
Reviewed by: jhb, np
Differential Revision: https://reviews.freebsd.org/D6109
a basic usage example. Although it is an
untypical example for the use of kqueue, it is
better than nothing and should get people started.
PR: 196844
Submitted by: fernando.apesteguia@gmail.com
Reviewed by: kib
Approved by: kib
MFC after: 5 days
Differential Revision: https://reviews.freebsd.org/D6082
Avoid logging inconsistency for the /dev/mem device at all. The driver
leaves memattr intact, and the corrective action in the device pager
handles it right.
In the logged warning, name the driver we blame, and show memory
attributes values.
Reported and tested by: pho
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D6149
driver is (or behaves identically to) /dev/mem. Remove the D_MEM flag
from random drivers.
Note that currently the D_MEM flag does not affect any behaviour, but
this going to change in the next commit.
Noted and reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
X-Differential revision: https://reviews.freebsd.org/D6149
