sys/cam/scsi/scsi_all.c:
- Added scsi_ata_pass_16 method
Which use ATA Pass-Through to send commands to the attached disk.
sys/cam/scsi/scsi_all.h:
- Added defines for all missing ATA Pass-Through commands values.
- Added scsi_ata_pass_16 method.
- Fixed a comment typo while I'm here
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
CAM. This can significantly improve performance particularly for SSDs
which don't suffer from seek latencies.
The sysctl / tunable kern.cam.sort_io_queues provides the systems default
setting where:-
0 = queued BIOs are NOT sorted
1 = queued BIOs are sorted (default)
Each device gets its own sysctl kern.cam.<type>.<id>.sort_io_queue
Valid values are:-
-1 = use system default (default)
0 = queued BIOs are NOT sorted
1 = queued BIOs are sorted
Note: Additional patch will look to add automatic use of none sorted queues
for none rotating media e.g. SSD's
Reviewed by: scottl
Approved by: pjd (mentor)
MFC after: 2 weeks
but execute the commands in regular way. There is no any reason to cook CPU
while the system is still fully operational. After this change polling in
CAM is used only for kernel dumping.
driver's periphs, acquiring and releaseing periph references while doing it.
Use it to iterate over the lists of ada and da periphs when flushing caches
and putting devices to sleep on shutdown and suspend. Previous code could
panic in theory if some device disappear in the middle of the process.
The vnode-backed md(4) has to map the unmapped bio because VOP_READ()
and VOP_WRITE() interfaces do not allow to pass unmapped requests to
the filesystem. Vnode-backed md(4) uses pbufs instead of relying on
the bio_transient_map, to avoid usual md deadlock.
Sponsored by: The FreeBSD Foundation
Tested by: pho, scottl
PREVENT ALLOW MEDIUM REMOVAL commands return errors on these devices
without returning sense data. In some cases unrelated following commands
start to return errors too, that makes device to be dropped by CAM.
every architecture's busdma_machdep.c. It is done by unifying the
bus_dmamap_load_buffer() routines so that they may be called from MI
code. The MD busdma is then given a chance to do any final processing
in the complete() callback.
The cam changes unify the bus_dmamap_load* handling in cam drivers.
The arm and mips implementations are updated to track virtual
addresses for sync(). Previously this was done in a type specific
way. Now it is done in a generic way by recording the list of
virtuals in the map.
Submitted by: jeff (sponsored by EMC/Isilon)
Reviewed by: kan (previous version), scottl,
mjacob (isp(4), no objections for target mode changes)
Discussed with: ian (arm changes)
Tested by: marius (sparc64), mips (jmallet), isci(4) on x86 (jharris),
amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)
Make umass return an error code if SCSI sense retrieval request
has failed. Make sure scsi_error_action honors SF_NO_RETRY and
SF_NO_RECOVERY in all cases, even if it cannot parse sense bytes.
Reviewed by: hselasky (umass), scottl (cam)
to avoid sending extra READ CAPACITY requests by dastart(). Schedule periph
again on reprobe completion, or otherwise it may stuck indefinitely long.
This should fix USB explore thread hanging on device unplug, waiting for
periph destruction.
Reported by: hselasky
and da_default_timeout where their current hardcoded values matched the current
default value for said tunables.
PR: kern/169976
Reviewed by: pjd (mentor)
Approved by: mav
DISKFLAG_CANDELETE. While this change makes this layer consistent
other layers such as UFS and ZFS BIO_DELETE support may not notice
any change made manually via these device sysctls until the device
is reopened via a mount.
Also corrected var order in dadeletemethodsysctl
PR: kern/169801
Reviewed by: pjd (mentor)
Approved by: mav
MFC after: 2 weeks
drivers.
The bug occurrs when a userland process has the driver instance
open and the underlying device goes away. We get the devfs
callback that the device node has been destroyed, but not all of
the closes necessary to fully decrement the reference count on the
CAM peripheral.
The reason is that once devfs calls back and says the device has
been destroyed, it is moved off to deadfs, and devfs guarantees
that there will be no more open or close calls. So the solution
is to keep track of how many outstanding open calls there are on
the device, and just release that many references when we get the
callback from devfs.
scsi_pass.c,
scsi_enc.c,
scsi_enc_internal.h: Add an open count to the softc in these
drivers. Increment it on open and
decrement it on close.
When we get a devfs callback to say that
the device node has gone away, decrement
the peripheral reference count by the
number of still outstanding opens.
Make sure we don't access the peripheral
with cam_periph_unlock() after what might
be the final call to
cam_periph_release_locked(). The
peripheral might have been freed, and we
will be dereferencing freed memory.
scsi_ch.c,
scsi_sg.c: For the ch(4) and sg(4) drivers, add the
same changes described above, and in
addition, fix another bug that was
previously fixed in the pass(4) and enc(4)
drivers.
These drivers were calling destroy_dev()
from their cleanup routine, but that could
cause a deadlock because the cleanup
routine could be indirectly called from
the driver's close routine. This would
cause a deadlock, because the device node
is being held open by the active close
call, and can't be destroyed.
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
Element Descriptor page if it is not supported. This removes one error
message from verbose logs during boot on systems with some enclosures.
Sponsored by: iXsystems, Inc.
safe in some cases to reduce CCB priority after it was scheduled with high
priority. This fixes reproducible deadlock when command sent through the
pass interface while ATA XPT recovers from command timeout.
Instead of that enforce priority at passioctl(). libcam provides no obvious
interface to specify CCB priority and so much (all?) code specifies zero
(highest) priority. This change limits pass CCBs priority to NORMAL run
level, allowing XPT to complete bus and device recovery after reset before
running any payload.
without holding SIM lock. It really doesn't need that lock, but adding it
removes that specific exception, allowing to assert locking there later.
Submitted by: ken@ (earlier version)
returns zero while request status is not CAM_REQ_CMP. That could cause
partial device attach or other unexpected results.
Found by: Clang Static Analyzer
drivers:
- Remove scsi_low_pisa.*, they were unused.
- Remove <compat/netbsd/physio_proc.h> and calls to the stubs in that
header. They were empty nops.
- Retire sl_xname and use device_get_nameunit() and device_printf() with
the underlying device_t instead.
- Remove unused {ct,ncv,nsp,stg}print() functions.
- Remove empty SOFT_INTR_REQUIRED() macro and the unused sl_irq member.
NetBSD/pc98 was never merged into the main NetBSD tree and is no longer
developed. Adding locking to these drivers would have made the compat
shims hard to impossible to maintain, so remove the shims to ease
future changes.
These changes were verified by md5. Some additional shims can be removed
that do affect the compiled results that I will probably do in another
round.
Approved by: nyan (tentatively)
of this hardware still running (close to twenty years now).
2. Quiesece and use ENC_VLOG instead of ENC_LOG for most
complaints. That is, they're visible with bootverbose, but
otherwise quiesced and not repeatedly spamming messages
with constant reminders that hardware in this space is
rarely fully compliant.
MFC after: 1 month
'encapsulating interface' used with IPsec and has nothing to do with
storage 'enclosure' services.
MFC after: 3 days
Noticed while: debugging why enc(4) is no longer automatically created
It includes three parts:
1) Modifications to CAM to detect media media changes and report them to
disk(9) layer. For modern SATA (and potentially UAS) devices it utilizes
Asynchronous Notification mechanism to receive events from hardware.
Active polling with TEST UNIT READY commands with 3 seconds period is used
for incapable hardware. After that both CD and DA drivers work the same way,
detecting two conditions: "NOT READY: Medium not present" after medium was
detected previously, and "UNIT ATTENTION: Not ready to ready change, medium
may have changed". First one reported to disk(9) as media removal, second
as media insert/change. To reliably receive second event new
AC_UNIT_ATTENTION async added to make UAs broadcasted to all periphs by
generic error handling code in cam_periph_error().
2) Modifications to GEOM core to handle media remove and change events.
Media removal handled by spoiling all consumers attached to the provider.
Media change event also schedules provider retaste after spoiling to probe
new media. New flag G_CF_ORPHAN was added to consumers to reflect that
consumer is in process of destruction. It allows retaste to create new
geom instance of the same class, while previous one is still dying.
3) Modifications to some GEOM classes: DEV -- to report media change
events to devd; VFS -- to handle spoiling same as orphan to prevent
accessing replaced media. PART class already handles spoiling alike to
orphan.
Reviewed by: silence on geom@ and scsi@
Tested by: avg
Sponsored by: iXsystems, Inc. / PC-BSD
MFC after: 2 months
Just free inclomplete daemon cache instead to let it retry next time.
Premature ses_softc_cleanup() caused NULL dereference when freed softc
was accessed later.
kern.cam.da.send_ordered, more in line with the other da sysctls/tunables.
PR: 169765
Submitted by: Steven Hartland <steven.hartland@multiplay.co.uk>
Reviewed by: mav
