Also rename the related functions in a similar way.
There are no functional changes.
For a packet coming in with IPsec tunnel mode, the default is
to only call into the firewall with the "outer" IP header and
payload.
With this option turned on, in addition to the "outer" parts,
the "inner" IP header and payload are passed to the
firewall too when going through ip_input() the second time.
The option was never only related to a gif(4) tunnel within
an IPsec tunnel and thus the name was very misleading.
Discussed at: BSDCan 2007
Best new name suggested by: rwatson
Reviewed by: rwatson
Approved by: re (bmah)
- to show a specific set: ipfw set 3 show
- to delete rules from the set: ipfw set 9 delete 100 200 300
- to flush the set: ipfw set 4 flush
- to reset rules counters in the set: ipfw set 1 zero
PR: kern/113388
Submitted by: Andrey V. Elsukov
Approved by: re (kensmith)
MFC after: 6 weeks
With the second (and last) part of my previous Summer of Code work, we get:
-ipfw's in kernel nat
-redirect_* and LSNAT support
General information about nat syntax and some examples are available
in the ipfw (8) man page. The redirect and LSNAT syntax are identical
to natd, so please refer to natd (8) man page.
To enable in kernel nat in rc.conf, two options were added:
o firewall_nat_enable: equivalent to natd_enable
o firewall_nat_interface: equivalent to natd_interface
Remember to set net.inet.ip.fw.one_pass to 0, if you want the packet
to continue being checked by the firewall ruleset after being
(de)aliased.
NOTA BENE: due to some problems with libalias architecture, in kernel
nat won't work with TSO enabled nic, thus you have to disable TSO via
ifconfig (ifconfig foo0 -tso).
Approved by: glebius (mentor)
address, to avoid confusing the users that a full address is
always required.
Submitted by: Josh Paetzel <josh@tcbug.org> (through freebsd-doc)
MFC after: 3 days
for example:
fwd tablearg ip from any to table(1)
where table 1 has entries of the form:
1.1.1.0/24 10.2.3.4
208.23.2.0/24 router2
This allows trivial implementation of a secondary routing table implemented
in the firewall layer.
I expect more work (under discussion with Glebius) to follow this to clean
up some of the messy parts of ipfw related to tables.
Reviewed by: Glebius
MFC after: 1 month
- 'tag' & 'untag' action parameters.
- 'tagged' & 'limit' rule options.
Rule examples:
pipe 1 tag tablearg ip from table(1) to any
allow ip from any to table(2) tagged tablearg
allow tcp from table(3) to any 25 setup limit src-addr tablearg
sbin/ipfw/ipfw2.c:
1) new macros
GET_UINT_ARG - support of 'tablearg' keyword, argument range checking.
PRINT_UINT_ARG - support of 'tablearg' keyword.
2) strtoport(): do not silently truncate/accept invalid port list expressions
like: '1,2-abc' or '1,2-3-4' or '1,2-3x4'. style(9) cleanup.
Approved by: glebius (mentor)
MFC after: 1 month
Since tags are kept while packet resides in kernelspace, it's possible to
use other kernel facilities (like netgraph nodes) for altering those tags.
Submitted by: Andrey Elsukov <bu7cher at yandex dot ru>
Submitted by: Vadim Goncharov <vadimnuclight at tpu dot ru>
Approved by: glebius (mentor)
Idea from: OpenBSD PF
MFC after: 1 month
doesn't exist or add one that is already present, if the -q flag
is set. Useful for "ipfw -q /dev/stdin" when the command above is
invoked from something like python or TCL to feed commands
down the throat of ipfw.
MFC in: 1 week
IPv6 support was committed:
- Stop treating `ip' and `ipv6' as special in `proto' option as they
conflict with /etc/protocols.
- Disuse `ipv4' in `proto' option as it is corresponding to `ipv6'.
- When protocol is specified as numeric, treat it as it is even it is
41 (ipv6).
- Allow zero for protocol as it is valid number of `ip'.
Still, we cannot specify an IPv6 over an IPv4 tunnel like before such
as:
pass ipv6 from any to any
But, now, you can specify it like:
pass ip4 from any to any proto ipv6
PR: kern/89472
Reported by: Ga l Roualland <gael.roualland__at__dial.oleane.com>
MFC after: 1 week
that debug.mpsafenet be set to 0. It is still possible for dead locks to
occur while these filtering options are used due to the layering violation
inherent in their implementation.
Discussed: -current, rwatson, glebius
* Correct handling of IPv6 Extension Headers.
* Add unreach6 code.
* Add logging for IPv6.
Submitted by: sysctl handling derived from patch from ume needed for ip6fw
Obtained from: is_icmp6_query and send_reject6 derived from similar
functions of netinet6,ip6fw
Reviewed by: ume, gnn; silence on ipfw@
Test setup provided by: CK Software GmbH
MFC after: 6 days
policy. It may be used to provide more detailed classification of
traffic without actually having to decide its fate at the time of
classification.
MFC after: 1 week
This is the last requirement before we can retire ip6fw.
Reviewed by: dwhite, brooks(earlier version)
Submitted by: dwhite (manpage)
Silence from: -ipfw
with the kernel compile time option:
options IPFIREWALL_FORWARD_EXTENDED
This option has to be specified in addition to IPFIRWALL_FORWARD.
With this option even packets targeted for an IP address local
to the host can be redirected. All restrictions to ensure proper
behaviour for locally generated packets are turned off. Firewall
rules have to be carefully crafted to make sure that things like
PMTU discovery do not break.
Document the two kernel options.
PR: kern/71910
PR: kern/73129
MFC after: 1 week
reversals+system lock ups if they are using ucred based rules
while running with debug.mpsafenet=1.
I am working on merging a shared locking mechanism into ipfw which
should take care of this problem, but it still requires a bit more
testing and review.
