gone rule. Optimise use of channels so that when a channel
is not ready another channel is used. Instead of using the SOF interrupt
use the system timer to drive the host statemachine. This might
give lower throughput and higher latency, but reduces the CPU usage
significantly. The DWC OTG host mode support should not be considered
for serious USB host controller applications. Some problems are still
seen with LOW speed USB devices.
Commit changes missed from r237435. Properly calculate the signal
trampoline addresses after the shared page is enabled. Handle FreeBSD
ABIs without shared page support too.
MFi386: revision 238792
Introduce curpcb magic variable.
Do this by checking if spa_namespace_lock is already held and not taking
it again in that case.
Add a comment explaining why that is done and why it is safe.
Reviewed by: pjd
MFC after: 24 days
It is possible that provider is destroyed while we are iterating over the
list.
Reported by: Brian Parkison <parkison@panzura.com>
Discussed with: phk
MFC after: 1 week
slot. This eventually results in exhaustion of the tid space, causing
new threads get tid -1 as identifier.
The bad effect of having the thread id equal to -1 is that
UMTX_OP_UMUTEX_WAIT returns EFAULT for a lock owned by such thread,
because casuword cannot distinguish between literal value -1 read from
the address and -1 returned as an indication of faulted
access. _thr_umutex_lock() helper from libthr does not check for
errors from _umtx_op_err(2), causing an infinite loop in
mutex_lock_sleep().
We observed the JVM processes hanging and consuming enormous amount of
system time on machines with approximately 100 days uptime.
Reported by: Mykola Dzham <freebsd levsha org ua>
MFC after: 1 week
we are actually editing table, which means editing rules,
thus we need writer access to 'em.
Fix this by offloading the update of table to the same taskqueue,
we already use for flushing. Since taskqueues major task is now
overloading, and flushing is optional, do mechanical rename
s/flush/overload/ in the code related to the taskqueue.
Since overloading tasks do unsafe referencing of rules, provide
a bandaid in pf_purge_unlinked_rules(). If the latter sees any
queued tasks, then it skips purging for this run.
In table code:
- Assert any lock in pfr_lookup_addr().
- Assert writer lock in pfr_route_kentry().
there is no need to release and reacquire the pmap and pvh global locks
around calls to uma_zfree(). Recursion into the pmap simply won't occur.
Eliminate the use of M_USE_RESERVE. It is deprecated and, in fact, counter-
productive, meaning that it actually makes the memory allocation request
more likely to fail.
Eliminate the macros pmap_{alloc,free}_l2_dtable(). They are of limited
utility, and pmap_free_l2_dtable() was inconsistently used.
Tidy up pmap_init(). In particular, change the initialization of the PV
zone so that it doesn't span the initialization of the l2 and l2table zones.
Tested by: jmg
On single core devices set_stackptrs is only ever called with cpu = 0 in
initarm and will be identical to the existing function. On SMP this needs
to be implemented for sys/arm/mp_machdep.c, but the implementations are
identical for each SoC.
-This line, and those below, will be ignored--
> Description of fields to fill in above: 76 columns --|
> PR: If a GNATS PR is affected by the change.
> Submitted by: If someone else sent in the change.
> Reviewed by: If someone else reviewed your modification.
> Approved by: If you needed approval for this commit.
> Obtained from: If the change is from a third party.
> MFC after: N [day[s]|week[s]|month[s]]. Request a reminder email.
> Security: Vulnerability reference (one per line) or description.
> Empty fields above will be automatically removed.
M altq/altq/altq_rmclass.c
is performed on the vnode mapping which is wired in other address space.
While there, explicitely assert that the page is unwired and zero the
wire_count instead of substract. The condition is rechecked later in
vm_page_free(_toq) already.
Reported and tested by: zont
Reviewed by: alc (previous version)
MFC after: 1 week
frames to occur.
* Create a new function which will set the bf_flags CLRDMASK bit
if required.
* For raw frames, always set CLRDMASK.
* For BAR, ADDBA frames, always set CLRDMASK.
* For everything else, check if CLRDMASK needs to be set before
calling tx_setds() or tx_setds11n().
* When unpausing a queue or drain/resetting it, set tid->clrdmask=1
just to ensure traffic starts flowing.
What I need to do:
* Modify that function to _clear_ the CLRDMASK if it's not required,
or retried frames may have CLRDMASK set when they don't need to.
(Which isn't a huge deal, but..)
Whilst I'm here:
* ath_tx_normal_xmit() should really act like the AMPDU session TX
functions - any incomplete frames will end up being assigned
ath_tx_normal_comp() which will decrement tid->hwq_depth - but that
won't have been incremented.
So whilst I'm here, add a comment to do that.
* Fix the debug print function to be slightly clearer about things;
it's not a good sign when I can't interpret my own debugging output.
I've done some testing on AR9280/AR5416/AR9160 STA and AP modes.
stack.
There are unfortunately quite a few odd cases in BAR TX and BAR TX
retransmission that I haven't yet fully diagnosed. So for now, add
this work-around so the resume() function isn't called too often,
decrementing pause to -1 (and causing things to stay paused.)
and owner_group strings that consist entirely of
digits, interpreting them as the uid/gid number.
This change was needed since new (>= 3.3) Linux
servers reply with these strings by default.
This change is mandated by the rfc3530bis draft.
Reported on freebsd-stable@ under the Subject
heading "Problem with Linux >= 3.3 as NFSv4 server"
by Norbert Aschendorff on Aug. 20, 2012.
Tested by: norbert.aschendorff at yahoo.de
Reviewed by: jhb
MFC after: 2 weeks
