requests.
sys/geom/geom_disk.h:
- Added d_delmaxsize which represents the maximum size of individual
device delete requests in bytes. This can be used by devices to
inform geom of their size limitations regarding delete operations
which are generally different from the read / write limits as data
is not usually transferred from the host to physical device.
sys/geom/geom_disk.c:
- Use new d_delmaxsize to calculate the size of chunks passed through to
the underlying strategy during deletes instead of using read / write
optimised values. This defaults to d_maxsize if unset (0).
- Moved d_maxsize default up so it can be used to default d_delmaxsize
sys/cam/ata/ata_da.c:
- Added d_delmaxsize calculations for TRIM and CFA
sys/cam/scsi/scsi_da.c:
- Added re-calculation of d_delmaxsize whenever delete_method is set.
- Added kern.cam.da.X.delete_max sysctl which allows the max size for
delete requests to be limited. This is useful in preventing timeouts
on devices who's delete methods are slow. It should be noted that
this limit is reset then the device delete method is changed and
that it can only be lowered not increased from the device max.
Reviewed by: mav
Approved by: pjd (mentor)
maximum sizes for said methods, which are used when processing BIO_DELETE
requests. This includes updating UNMAP support discovery to be based on
SBC-3 T10/1799-D Revision 31 specification.
Added ATA TRIM support to cam scsi devices via ATA Pass-Through(16)
sys/cam/scsi/scsi_da.c:
- Added ATA Data Set Management TRIM support via ATA Pass-Through(16)
as a delete_method
- Added four new probe states used to identity available methods and their
limits for the processing of BIO_DELETE commands via both UNMAP and the
new ATA TRIM commands.
- Renamed Probe states to better indicate their use
- Added delete method descriptions used when informing user of issues.
- Added automatic calculation of the optimum delete mode based on which
method presents the largest maximum request size as this is most likely
to result in the best performance.
- Added WRITE SAME max block limits
- Updated UNMAP range generation to mirror that used by ATA TRIM, this
optimises the generation of ranges and fixes a potential overflow
issue in the count when combining multiple BIO_DELETE requests
- Added output of warnings about short deletes. This should only ever
be triggered on devices that fail to correctly advertise their supported
delete modes / max sizes.
- Fixed WS16 requests being incorrectly limited to 65535 in length.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
so its available for use in generic scsi code.
This is a pre-requirement for using VPD queries to determine available SCSI
delete methods within scsi_da.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
commands to an ATA device attached via a SCSI control.
sys/cam/scsi/scsi_all.c:
- Added scsi_ata_identify, scsi_ata_trim
Which use ATA Pass-Through to send commands to the attached disk.
sys/cam/scsi/scsi_all.h:
- Added defines for all missing ATA Pass-Through commands values.
- Added scsi_ata_identify, scsi_ata_trim methods used in ATA TRIM
support.
- Added scsi_vpd_logical_block_prov structure used when querying for
the supported sizes UNMAP commands.
- Added scsi_vpd_block_limits structure used when querying for the
supported sizes of the UNMAP command.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
size of a delete request sent to the providing device performed by g_dev_ioctl.
This allows the kernel and apps via ioctl e.g. newfs -E to request large LBA
deletes which siginificantly improves performance.
Previously this was hard coded to 65536 sectors, the new default is 262144
which doubles the throughput of deletes on commonly available SSD's.
In tests on a Intel 520 120GB FW: 400i disk it improved the delete throughput
from 1.6GB/s to over 2.6GB/s on a full disk delete such as that done via
newfs -E
For some SSD's where delete time is pretty much constant, no matter what
the request, setting this to 0 will provide significantly better throughput
e.g. Samsung 840 240GB FW DXT07B0Q @ 262144 = 79G/s, @ 0 = 2259G/s
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
I/O clock. Thankfully, the simple executive provies a way to querry
the proper clock that works on all models. Move to asking for the SCLK
via this interface.
This gets the serial console working after we start init and open the
console and set the divisor (which turned the output from good to
bad). I can login on the console now.
and tuned value, we would advertise the unsupported value to CAM and it would
merrily destroy the controller with way too many IO operations.
This manifests itself in a Zero Memory RAID configuration for a P410 and
possibly other controllers.
Obtained from: Yahoo! Inc.
MFC after: 2 weeks
in the pcb. setjmp/longjmp in the kernel also used these values, so
continue to use them although their use isn't technically the pcb
register array (matching is all that's important for setjmp/longjmp in
the kernel). Finally, eliminate the old register names from regnum.h.
This is a lexical change only. The non-debug .o files have the same md5.
same place as dst, or to the sockaddr in the routing table.
The const constraint of gw makes us safe from modifing routing table
accidentially. And "onstantness" of dst allows us to remove several
bandaids, when we switched it back at &ro->ro_dst, now it always
points there.
Reviewed by: rrs
Rework the guest register fetch code to allow the RIP to
be extracted from the VMCS while the kernel decoder is
functioning.
Hit by the OpenBSD local-apic code.
Submitted by: neel
Reviewed by: grehan
Obtained from: NetApp
Merge vendor bugfix for a possible deadlock related to async destroy
and improve write performance by introducing a new lock protecting
tx_open_txg.
Illumos ZFS issues:
3642 dsl_scan_active() should not issue I/O to determine if async
destroying is active
3643 txg_delay should not hold the tc_lock
MFC after: 1 week
route. What it was is there are two places in ip_output.c
where we do a goto again. One place was fine, it
copies out the new address and then resets dst = ro->rt_dst;
But the other place does *not* do that, which means earlier
when we found the gateway, we have dst pointing there
aka dst = ro->rt_gateway is done.. then we do a
goto again.. bam now we clobber the default route.
The fix is just to move the again so we are always
doing dst = &ro->rt_dst; in the again loop.
PR: 174749,157796
MFC after: 1 week
GDT from the correct segment, otherwise a triple fault would be caused.
In some virtual environments (VMware, VirtualBox, etc) this could lead
to a unhandled error or hang in the guest emulation software.
Thanks to avg and jhb for a few hints in the right direction.
Noticed by: Jeremy Chadwick <jdc@koitsu.org> (and many others)
MFC after: 1 week
instead of kernel_map size to prevent kernel memory exhaustion
by mbufs and a subsequent panic on physical page allocation
failure.
On architectures without a direct map all mbuf memory (except
for jumbo mbufs larger than PAGE_SIZE) comes from kmem_map.
It is the limiting factor hence.
For architectures with a direct map using the size of kmem_map
is a good proxy of available kernel memory as well. If it is
much smaller the mbuf limit may be sub-optimal but remains
reasonable, while avoiding panics under exhaustion.
The overall mbuf memory limit calculation may be reconsidered
again later, however due to the many different mbuf sizes and
different backing KVM maps it is a tricky subject.
Found by: pho's new network stress test
Pointed out by: alc (kmem_map instead of kernel_map)
Tested by: pho
duplicate ACK make sure we actually have new data to send.
This prevents us from sending unneccessary pure ACKs.
Reported by: Matt Miller <matt@matthewjmiller.net>
Tested by: Matt Miller <matt@matthewjmiller.net>
MFC after: 2 weeks
