the handler address. Add a mark to distinguish between filter and
handler.
Note that the arguments for both filter and handler are same.
Sponsored by: The FreeBSD Foundation
Reviewed by: jhb
MFC after: 1 week
is configured for higher rates (lower than max) but higher TX power
is configured for the lower rates, above the configured cap, to improve
long distance behaviour.
* Add the rest of the missing GPIO output mux types;
* Add in a new debug category;
* And a new MCI btcoex configuration option in ath_hal.ah_config
Obtained from: Qualcomm Atheros
* arge0 is MII
* arge1 is GMII
* the MDIO bus is on arge1, not arge0
* the default switch config is to have ports 0-3 as the switch group,
with port 4 being an external PHY dedicated to arge0 (ie, 'cpu' port.)
Whilst I'm here, remove unused bits and pieces from the config.
Tested:
* AP121, ping on both arge0 and arge1
* Tested switch port detection using etherswitchcfg
* Enable RX and host interrupts during bus probe/attach
* Disable all interrupts (+ host ISR) during bus detach
* Enable TX DONE interrupt only when we start transmitting; clear it when
we're done.
* The RX/TX FIFO depth is still conjecture on my part. I'll fix this
shortly.
* The TX FIFO interrupt isn't an "empty" interrupt, it's an "almost empty"
interrupt. Sigh. So..
* .. in ar933x_bus_transmit(), wait for the FIFO to drain before
continuing.
I dislike having to wait for the FIFO to drain, alas.
Tested:
* Atheros AP121 board, AR9331 SoC.
TODO:
* RX/TX overflow, RX error, BREAK support, etc.
* Figure out the true RX/TX FIFO depth.
disks such as SSD's
Adds the ability to run ATA commands via the SCSI ATA Pass-Through(16) comand
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
r249017:
Some cosmetic things:
- Unify device to target insertion inside xpt_alloc_device() instead of
duplicating it three times.
- Remove extra checks for empty lists of devices and targets on release
since zero refcount check also implies it.
- Reformat code to reduce indentation.
r249103:
- Add lock assertions to every point where reference counters are modified.
- When reference counters are reaching zero, add assertions that there are
no children items left.
- Add a bit more locking to the xptpdperiphtraverse().
Move CAM_DEBUG_CDB messages from the point of queuing to the point of
sending to SIM. That allows to inspect real requests execution order,
respecting priorities, freezing, etc.
MFC after: 2 weeks
This implements the bus transmit/receive/sigchg/ipend methods with
a polled interrupt handler (ipend) rather than enabling hardware
interrupts.
The FIFO is faked at 16 bytes deep for now, just so the transmit
IO side doesn't suck too bad (the callout frequency limits how quickly
IO is flushed to the sender, rather than scheduling the callout more
frequently whilst there's active TX. But I digress.)
Tested:
* Atheros AP121 (AR9330) reference board, booting to multi-user interactive
mode.
buffers (ie, >4GB on amd64.)
The underlying problem was that PREREAD doesn't sync the mbuf
with the DMA memory (ie, bounce buffer), so the bounce buffer may
have had stale information. Thus it was always considering the
buffer completed and things just went off the rails.
This change does the following:
* Make ath_rx_pkt() always consume the mbuf somehow; it no longer
passes error mbufs (eg CRC errors, crypt errors, etc) back up
to the RX path to recycle. This means that a new mbuf is always
allocated each time, but it's cleaner.
* Push the RX buffer map/unmap to occur in the RX path, not
ath_rx_pkt(). Thus, ath_rx_pkt() now assumes (a) it has to consume
the mbuf somehow, and (b) that it's already been unmapped and
synced.
* For the legacy path, the descriptor isn't mapped, it comes out of
coherent, DMA memory anyway. So leave it there.
* For the EDMA path, the RX descriptor has to be cleared before
its passed to the hardware, so that when we check with
a POSTREAD sync, we actually get either a blank (not finished)
or a filled out descriptor (finished.) Otherwise we get stale
data in the DMA memory.
* .. so, for EDMA RX path, we need PREREAD|PREWRITE to sync the
data -> DMA memory, then POSTREAD|POSTWRITE to finish syncing
the DMA memory -> data.
* Whilst we're here, make sure that in EDMA buffer setup (ie,
bzero'ing the descriptor part) is done before the mbuf is
map/synched.
NOTE: there's been a lot of commits besides this one with regards to
tidying up the busdma handling in ath(4). Please check the recent
commit history.
Discussed with and thanks to: scottl
Tested:
* AR5416 (non-EDMA) on i386, with the DMA tag for the driver
set to 2^^30, not 2^^32, STA
* AR9580 (EDMA) on i386, as above, STA
* User - tested AR9380 on amd64 with 32GB RAM.
PR: kern/177530
most kernels before FreeBSD 9.0. Remove such modules and respective kernel
options: atadisk, ataraid, atapicd, atapifd, atapist, atapicam. Remove the
atacontrol utility and some man pages. Remove useless now options ATA_CAM.
No objections: current@, stable@
MFC after: never
done in ixgbe, thanks to Mike Karels for this fix. When exiting
promiscuous mode MPE bit was being unconditionally cleared, this
should not be done if we are in MAX multicast groups.
Allow boothowto and bootverbose to be set via kernel options, which
is useful on architectures that are unable to rely on a boot loader
to pass configuration variables to the kernel.
Submitted by: rwatson
