gif(4) interface. Add new option "ignore_source" for gif(4) interface.
When it is enabled, gif's encapcheck function requires match only for
packet's destination address.
Differential Revision: https://reviews.freebsd.org/D2004
Obtained from: Yandex LLC
MFC after: 2 weeks
Sponsored by: Yandex LLC
particular, switch to the proc0 pmap to have expected %cr3 and PCID
for the thread0 during initialization, and the up to date pm_active
mask.
pmap_pinit0() should be done after proc0->p_vmspace is assigned so
that the amd64 pmap_activate() find the correct curproc pmap.
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
suspended thread itself, on the return path from
thread_suspend_check(). A consequence is that return from
thread_single_end(SINGLE_BOUNDARY) may leave p_boundary_count
non-zero, it might be even equal to the threads count.
Now, assume that we have two threads in the process, both calling
execve(2). Suppose that the first thread won the race to be the
suspension thread, and that afterward its exec failed for any reason.
After the first thread did thread_single_end(SINGLE_BOUNDARY), second
thread becomes the process suspension thread and checks
p_boundary_count. The non-zero value of the count allows the
suspension loop to finish without actually suspending some threads.
In other words, we enter exec code with some threads not suspended.
Fix this by decrementing p_boundary_count in the
thread_single_end()->thread_unsuspend_one() during marking the thread
as runnable. This way, a return from thread_single_end() guarantees
that the counter is cleared. We do not care whether the unsuspended
thread has a chance to run.
Add some asserts to ensure the state of the process when single
boundary suspension is lifted. Also make thread_unuspend_one()
static.
In collaboration with: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
It simplifies understanding of the sfxge_tx_packet_add() logic and
avoids passing of 'locked' to called function.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2547
It is simply not required since the kernel checks corresponding
IFCAP_TSOx capability and CSUM_TSO in hw-assisted offloads.
Note that CSUM_TSO is two bits (CSUM_IP_TSO|CSUM_IP6_TSO) and both bits
are set in IPv4 and IPv6 mbufs.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2546
Also it is cheaper to check Rx descriptor flags than TCP protocol in IP
header.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2542
For consistency with the naming conventions used by the other
implementations kill armv7_sleep and keep armv7_cpu_sleep.
Differential Revision: https://reviews.freebsd.org/D2537
Submitted by: John Wehle
Reviewed by: ian@, andrew@
Netfront has to wait for the backend to switch to state XenbusStateConnected
before sending the ARP request, or else the backend might not be connected
and thus the packet will be lost.
Sponsored by: Citrix Systems R&D
MFC after: 1 week
This is one of the few post gcc4.2 builtins that has been implemented by
clang:
__builtin_unreachable is used to indicate that a specific point in the
program cannot be reached, even if the compiler might otherwise think it
can. This is useful to improve optimization and eliminates certain
warnings.
Hinted by: NetBSD
Differential Revision: https://reviews.freebsd.org/D2536
This allows functions that retrieve and inspect pthread_attr_t objects to
work correctly: querying the cpuset_t size is part of querying CPU
affinity information, which is part of creating a complete pthread_attr_t.
Approved by: rwatson (mentor)
Reviewed by: pjd
Sponsored by: NSERC
Tx checksum offload may be enabled/disabled.
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2543
needs to be enabled by adding "kern.racct.enable=1" to /boot/loader.conf.
Differential Revision: https://reviews.freebsd.org/D2407
Reviewed by: emaste@, wblock@
MFC after: 1 month
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Split IFCAP_HWCSUM to IFCAP_RXCSUM and IFCAP_TXCSUM to highlight Tx and Rx.
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2541
Present implementation of large sync writes is too strict and so can be
quite slow. Instead of doing that, execute large async write in chunks,
syncing each chunk separately.
It would be good to fix large sync writes too, but I leave it to somebody
with more skills in this area.
Reviewed by: rmacklem
MFC after: 1 week
GICv3 allows to distribute interrupts to more than 8 cores served by
the previous GIC revisions. GICv3 introduces additional logic in form
of Re-Distributors associated with particular CPUs to determine
the highest priority interrupts and manage PPIs and LPIs
(Locality-specific Peripheral Interrupts). Interrupts routing is
based on CPUs' affinity numbers. CPU interface was changed to be
accessible via CPU System Registers and this is the preferred
(and supported) method in this driver.
Obtained from: Semihalf
Reviewed by: andrew, emaste, ian, imp
Sponsored by: The FreeBSD Foundation
The GCC visibility attributes were introduced in GCC 4.0.
Apparently the "protected" attribute was introduced only
until GCC 4.2, but we are not currently using it.
MFC after: 1 week
The consumers of hw.intrnames expect a NULL byte at end of the string
containing the interrupt names.
On ARM all the interrupt name slots are initialized and this leave no room
for the terminating NULL byte, which makes vmstat read beyond the end of
intrnames.
PR: 199891
Tested on: RPi 2 and BeagleBone Black
even if there was non-zero number of restarts, we would unref/clear
all value references and start ipfw_link_table_values() once again
with (mostly) cleared "tei" buffer.
Additionally, ptei->ptv stores only to-be-added values, not existing ones.
This is a forgotten piece of previous value refconting implementation,
and now it is simply incorrect.
frames to 0
From IEEE Std. 802.11-2012, 8.3.2.1 "Data frame format", p. 415 (513):
"The Sequence Control field for QoS (+)Null frames is ignored by the receiver
upon reception."
At this moment, any <mode>_input() function interprets them as regular QoS data
frames with TID = 0. As a result, stations, that use another TX sequence for
QoS Null frames (e.g. wpi(4), where (QoS) Null frames are generated by the
firmware), may experience significant packet loss with any other NIC in hostap
mode.
Tested:
* wpi(4) (author)
* iwn(4) - Intel 5100, STA mode (me)
PR: kern/200128
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
The aml8726-m3 SoC is identified as a Cortex A9-r2 rev 4 CPU and
it hangs sometimes during the boot when WFI is used by the kernel.
Differential Revision: https://reviews.freebsd.org/D2473
Submitted by: John Wehle
Suggested by: ian@
packets on tunnel interfaces. Add support of these ioctls to gre(4),
gif(4) and me(4) interfaces. For incoming packets M_SETFIB() should use
if_fib value from ifnet structure, use proper value in gre(4) and me(4).
Differential Revision: https://reviews.freebsd.org/D2462
No objection from: #network
MFC after: 2 weeks
Sponsored by: Yandex LLC
because a link where looped back NS messages are permanently observed
does not work with either NDP or ARP for IPv4.
- draft-ietf-6man-enhanced-dad is now RFC 7527.
Discussed with: hiren
MFC after: 3 days
Summary:
The Freescale PCIe Root Complex shows up as a Processor class device, PowerPC
subclass, so the generic PCI code ignores it for a bridge. This adds support
for it.
As part of this, update the Freescale PCI hostbridge driver, to allow probing
beyond the root complex, instead of only allowing "proper" PCI-PCI bridges.
Reviewers: #powerpc, marcel, nwhitehorn
Reviewed By: nwhitehorn
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2442
Relnotes: yes
because the i386 pmap on which the new armv6 pmap is based had it, and in
r281707 pmap_lazyfix() was removed from the i386 pmap.
Discussed with: kib
Submitted by: Michal Meloun (via Svatopluk Kraus)
main ARMv6 target, the Raspberry Pi, doesn't support Thumb-2.
This as been tested with a Thumb-2 userland, however building one is
currently unsupported as there are known toolchain issues breaking some
binaries. Further work will also be needed to decide on the method of
selecting which instruction set to build for, and to benchmark both to
find how building everything as Thumb-2 will affect performance.
Relnotes: yes
This allows to ensure that we do not write to a file that was opened
for reading only or vice versa.
Also, use the correct capability in in zfs_ioc_send_new().
Differential Revision: https://reviews.freebsd.org/D2382
Reviewed by: delphij
MFC after: 17 days
Sponsored by: ClusterHQ
