controller does not perform automatic switching from 1000Mbps link
to 10/100Mbps link when WOL is activated. Implement establishing
10/100Mps link with auto-negotiation in driver. Link status change
handler was modified to remove taskqueue based approach since driver
now needs synchronous handling for link establishment.
Submitted by: Yamagi Burmeister (lists <> yamagi.org ) (initial version)
Tested by: Yamagi Burmeister (lists <> yamagi.org )
MFC after: 1 week
obtained from Linux forcedeth driver.
While I'm here move creating a sysctl node for process_limit to
function nfe_sysctl_node().
Tested by: "Arno J. Klaassen" < arno <at> heho dot snv dot jussieu dot fr >
allocator for jumbo frame. Also remove unneeded jlist lock which
is no longer required to protect jumbo buffers.
With these changes jumbo frame performance of nfe(4) was slightly
increased and users should not encounter jumbo buffer allocation
failure anymore.
Because nfe(4) hardware doesn't support SG on Rx path, supporting
jumbo frame requires very large contiguous kernel memory(i.e. several
mega bytes). In case of lack of contiguous kernel memory that
allocation request may always fail. However nfe(4) can operate on normal
sized MTU frames, so go ahead and just disable jumbo frame support.
While I'm here add a new tunable "hw.nfe.jumbo_disable" to disable
jumbo frame support.
In nfe_poll, make sure to invoke correct Rx handler.
Approved by: re (kensmith)
o s/printf/device_printf/g
o Nuke OpenBSDism.
o Nuke NetBSD/OpenBSD specific DMA sync operations.(we don't have a way
to sync a single descriptor within a DMA map.)
o Remove recursive mutex.
o bus_dma(9) clean up.
o 40bit DMA address support.
o Add protection for Rx map load failure.
o Fix a long standing bug for watchdog timeout. [1]
o Add additional protections, missing Tx completion interrupt, losing
start Tx command, for watchdog timeout.
o Switch to taskqueue(9) API to handle interrupts.
o Use our own timer for watchdog instead of if_watchdog/if_timer
interface.
o Advertise VLAN header length/capability correctly to upper layer.
o Remove excessive kernel stack consumption in nfe_encap().
o Handle highly fragmented mbuf chains correctly.
o Enable etherenet address reprogramming with ifconfig(8).
o Add ALTQ/TSO, MSI/MSIX support.
o Increased Rx ring to 256 descriptors from 128.
o Align Tx/Rx descriptor ring on sizeof(struct nfe_desc64) boundary.
o Remove alignment restrictions on Tx/Rx buffers.
o Rewritten jumbo frame support code.
o Add support for hardware assistend VLAN tag insertion/stripping.
o Add support for Tx/Rx flow control based on patches from Peer Chen. [2]
o Add a routine that detects whether ethernet address swap routines is
required. [3]
o Add a workaround that take MAC/PHY out of power down mode.
o Add suspend/resume support.
o style(9) and code clean up.
Special thanks to Shigeaki Tagashira, the original porter of nfe(4),
who submitted lots of patches, performed uncountable number of
regression tests and maintained nfe(4) for a long time. Without his
enthusiastic help and support I could never have completed this
overhauling task.
The only weak point of nfe(4) compared to nve(4) is instability of
manual half-duplex media selection on certain hardwares(auto sensing
media type should work for all cases, though). This was a long
standing bug of nfe(4) and I still have no idea why it doesn't work
on some hardwares.
Obtained from: OpenBSD [1]
Submitted by: Peer Chen < pchen at nvidia dot com > [2], [3]
Reviewed by: Shigeaki Tagashira < shigeaki AT se DOT hiroshima-u DOT ac DOT jp >
Tested by: Shigeaki Tagashira, current
Discussed with: current
Silence from: obrien
This driver was ported from OpenBSD by Shigeaki Tagashira
<shigeaki@se.hiroshima-u.ac.jp> and posted at
http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html
It was additionally cleaned up by me.
It is still a work-in-progress and thus is purposefully not in GENERIC.
And it conflicts with nve(4), so only one should be loaded.
