- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
attach chips with generic Marvell (non-HighPoint) PCI identification.
These chips are also supported by ata(4). Some vendors, like Supermicro,
are using same chips without providing HPT RAID BIOS.
PR: kern/120842, kern/136750
It is necessary to make sure cpi->transport is set for xpt_scan_bus() to
work properly.
Submitted by: Bernhard Schmidt (scb+freebsd-current <at> techwires
<dot> net)
Reviewed by: scottl
Approved by: re (kib)
/boot/kernel/hptrr.ko
/etc/mail/*.cf
/lib/libcrypto.so.5
/usr/bin/ntpq
/usr/sbin/amd
/usr/sbin/iasl
/usr/sbin/ntpd
/usr/sbin/ntpdate
/usr/sbin/ntpdc
There does not appear to be any purpose to having these timestamps, and
they have the irritating consequence that the aforementioned files will
be different every time they are rebuilt.
After this commit, the only remaining build timestamps are in the kernel,
the boot loaders, /usr/include/osreldate.h (the year in the copyright
notice), and lib*.a (the timestamps on all of the included .o files).
Reviewed by: scottl (hptrr), gshapiro (sendmail), simon (openssl),
roberto (ntp), jkim (acpica)
Approved by: re (kib)
HPT drivers would sometimes test the value of a preprocessor definition but
not always make sure that the definition existed in the first place, leading
to warnings on newer compilers. I blindly assumed the same with this driver,
and it turned out to be wrong and to enable some code that doesn't work.
cards:
o RocketRAID 172x series
o RocketRAID 174x series
o RocketRAID 2210
o RocketRAID 222x series
o RocketRAID 2240
o RocketRAID 230x series
o RocketRAID 231x series
o RocketRAID 232x series
o RocketRAID 2340
o RocketRAID 2522
Many thanks to Highpoint for their continued support of FreeBSD.
Submitted by: Highpoint
