(I completely mis-read the rfc last time 'round!)
This means:
o Better CCP/WARN Reset diagnostics.
o After we've sent a REQ and before we've received an ACK, we drop
incoming compressed data and send another REQ.
o Before sending an ACK, re-sequence all pending PRI_NORMAL data in
the modem queue so that pending packets won't get to the peer
*after* the ResetAck.
o Send ACKs with the `identifier' from the REQ frame.
o After we've received a correct ACK, duplicate ACKs are ok (and will
reset our history).
o Incorrect ACKs (not matching the last REQ) are moaned about and dropped.
Also,
o Calculate the correct FCS after compressing a packet. DEFLATE
*may* produce an mbuf with more than a single link in the chain,
but HdlcOutput didn't know how to calculate the FCS :-(
o Make `struct fsm'::reqid a u_char, not an int.
This fix will prevent us from sending id `255' 2,000,000,000 times
before wrapping to `0' for another 2,000,000,000 sends :-/
o Bump the version number a little.
The end result: DEFLATE now works over an unreliable link layer.
I can txfr a 1.5Mb kernel over a (rather bad) null-modem
cable at an average of 21679 bytes per second using rcp.
Repeat after me: Don't test compression using a loopback ppp/tcp setup as
we never lose packets and therefore never have to reset!
Validate the peers suggested IP by attempting to make a routing table
entry.
Give up IPCP negotiation if the peer NAKs us with an unusable IP.
Always SIOCDIFADDR then SIOCAIFADDR when configuring the tun device.
Using SIOCSIFDSTADDR allows duplicate dst addresses (which we don't
want)!!!
Allow up to 200 interface names (was 50) (now that ppp can play server
properly).
Up the version number (1.5 -> 1.6).
Cosmetic:
Log unexpected CCP packets in the CCP log rather than the ERROR log.
Log unexpected Config Reqs in the appropriate LCP/IPCP/CCP log rather
than the ERROR log.
Log failed route additions and deletions with WARN, not TCPIP.
Log the option id and length for unrecognised IPCP options.
Change some .Sq to .Ar in the man page.
(I *really* meant to do this *before* committing the
deflate changes in the first place - oops).
Pppd is horribly broken in this respect - refer to the
ppp man page for details. Ppp *WON'T* negotiate deflate
with pppd by default - you must ``enable'' and ``accept''
``pppd-deflate'' in your config.
While I'm in there, update the cftypes in ccp.c so that
we recognise some more protocols (we don't actually do
anything with them - just send a REJ).
Remove extraneous decls.
Add ``const'' to several places.
Allow ``make NOALIAS=1'' to remove IP aliasing.
Merge with OpenBSD - only the Makefiles vary.
We can now survive a compile with
-Wall -Wbad-function-cast -Wcast-align -Wcast-qual
-Winline -Wmissing-declarations -Wmissing-prototypes
-Wnested-externs -Wpointer-arith -Wredundant-decls
-Wshadow -Wstrict-prototypes -Wwrite-strings -Wchar-subscripts
(although the Makefile just contains -Wall).
o Add "allow" command:
"allow users a b c" gives access to users a, b and c.
"allow modes auto" gives those users access to auto mode only.
"allow users *" and "allow modes *" are accepted.
No users and all modes are allowed by default.
UID 0 can do anything.
o Set the current label with the "load" and "dial" commands
so that the call to ppp.linkdown makes sense.
o Up the verison number.
o Don't OR MODE_AUTO for -background and -ddial.
o Don't OR MODE_INTER when we get a diagnostic connection.
o Allow up to 40 args per line (was 20).
o "set ifaddr" only changes the interface in AUTO mode (with other
modes, it happens after IPCP negotiation).
o Sort command descriptions in the man page.
o Support -dedicated mode where we just talk ppp forever (no login etc).
o Report modem connect time properly
o Report bytes in/out over physical media
o Fix phases (TERMINATE is *higher than* DEAD)
o Do a LayerFinish from LcpDown
o Bring down IPCP & CCP when we enter PHASE_TERMINATE
o Give a new prompt when we go to PHASE_DEAD
o Stop the modem timer properly when idle
o Treat sig 15 like an exiting carrier loss
o Log (DEBUG) offline & online transitions
o Add missing $Id$s
o Move extern decls from .c -> .h files
o Staticize
o Remove #includes from .h files
o style(9)ify includes
o bcopy -> memcpy
bzero -> memset
bcmp -> memcmp
index -> strchr
rindex -> strrchr
o Move timeout.h -> timer.h (making it consistent w/ timer.c)
o Add -Wmissing-prototypes
o Output the correct device for "show modem"
while in -direct mode.
o Cosmetic: Moan a bit more when we can't open
the [modem] device.
o Call OpenModem() in a more "natural" way.
o Add some LogDEBUG in OpenModem().
Insist that uid == 0 for client ppp
Disallow client sockets if no password is specified
Don't exit on failure to open client socket for listening
Allow specification of null local password
Use reasonable size (smaller) ``vector''s in auth.c
Fix "passwd ..." usage message
Insist on "all" as arg to "quit" (if any)
Drop client socket connection before Cleanup() when "quit all"
This tells ppp to loopback packets addressed to
the ppp interface IP coming *from* the tun
device.
This means that you can ping the tun interface IP
from inside :-)
idependently time out any of the FSMs.
Split LCP logging into LCP, IPCP and CCP logging,
and make room in "struct fsm" for the log level
that the state machine should use.
"set stopped" directive. If the timeout occurs
it will cause a "Down" event, hanging up the line
if it's still up. This *isn't* part of the FSM
diagram, but I consider it ok as a "higher level
implementation specific timeout" as specified in
the rfc ;-}
Discussed briefly with: joerg
o Use syslog
o Remove references to stdout/stderr (incl perror())
o Introduce VarTerm - the interactive terminal or zero
o Allow "set timeout" to affect current session
o Change "set debug" to "set log"
o Allow "set log [+|-]flag"
o Make MSEXT and PASSWDAUTH stuff the default
o Move all #ifdef DEBUG stuff into the code - this
shouldn't be too much overhead. It's now controlled
with "set log +debug"
o Add "set log command, debug, tun, warn, error, alert"
o Remove cdefs.h, and assume an ansi compiler.
o Improve all diagnostic output
o Don't trap SIGSEGV
o SIGHUP now terminates again (log files are controlled
by syslog)
o Call CloseModem() when changing devices
o Fix parsing of third arg of "delete"
I think this fixes the "magic is same" problems that some
people have been experiencing.
The man page is being rewritten. It'll follow soon.
alias commands simply won't work. Only root may specify the
location of the alias lib (otherwise, it's hard-coded).
Make logprintf silently fail if LogOpen hasn't been called.
Suggested by: eivind
the connection after an unexpected loss of carrier:
set reconnect timer ntries
The man page warns against using this command when your
timeout value is slightly more than the other sides :{}
Suggested by: burton@bsampley.vip.best.com (Burton Sampley)
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
on their own without even attempting to get concensus in the IETF, but
there are also lots of Win95/NT boxes out there.
CLoses PR#1494
Submitted-By: Peter Childs <pjchilds@imforei.apana.org.au>
A settable redial timer helps to avoid the problem where both ends
of a link want to dial at the same time and the line winds up busy
for both ends. The process id is logged in /var/run/PPP.system where
system is the name of the called system. When both ends of a link
are running in demand dial mode, you need an easy way to get the pid
of the ppp on the called end so it can be killed and re-started with
-direct or pppd started to handle the incoming ppp session.
2. Add secret description for "set timeout" to man.
Reviewed by: Atsushi Murai <amurai@spec.co.jp>
Submitted by: John Capo <jc@irbs.com>
2. Optimize ModemQlen.
3. Sending ProtoReject for Unknow protocol (i.e. IPX)
4. Avoid select looping by reading tun under the high system load.
5. Adding Local version String for maintenance.
6. Just more speak rather silent ignore if you type invalid key words.
o Supporting SYNC SIO device (But need a device driver)
- add "set speed sync"
o Fixing bug for Predictor-1 function.
o Add new parameter that re-sent interval for set timeout commands.
o Improving RTT (Round Trip Time) and reducing processor time.
- Previous Timer service was using polling, and now using
SIGALRM ;-)
- A 0.94beta2 will not work correctly....
-- Follows are additinal feature not including 0.94beta2
o Support Proxy ARP
- add "enable/disable proxy" commands
o Marging common routine in CHAP/PAP.
o Enhancing LCP/IPCP log information.
o Support local Authfication connection on port 300x and tty.
- You can set up pair of your "hostname -s" and
password in ppp.secret. if either ppp.secret file nor
your hostname line don't exist, It will notify a message
and working as same as previous version.(Backword compatibility)
- If you did set up them, It's allow connection but nothing to do
except help and passwd command.
- add "passwd yourpasswd" commands
o Support afilter - keep Alive filter that a packet can send/receiving
according to ifilter/ofilter but doesn't count it as preventing idle
timer expires.
- Same syntax of other filters.
o Fixing bugs reported by current user for previous one. Thanks !!
Reviewed by: Atsushi Murai (amurai@spec.co.jp)
