- Re-probe xfp / sfp+ socket on link events, in case user
has changed transceiver
- correctly report current media to avoid confusing lagg (reported by Panasas)
- Report link speed (submitted by yongari)
Reviewed by: yongari (earlier version)
MFC after: 7 days
This driver was written by Alexander Pohoyda and greatly enhanced
by Nikolay Denev. I don't have these hardwares but this driver was
tested by Nikolay Denev and xclin.
Because SiS didn't release data sheet for this controller, programming
information came from Linux driver and OpenSolaris. Unlike other open
source driver for SiS190/191, sge(4) takes full advantage of TX/RX
checksum offloading and does not require additional copy operation in
RX handler.
The controller seems to have advanced offloading features like VLAN
hardware tag insertion/stripping, TCP segmentation offload(TSO) as
well as jumbo frame support but these features are not available
yet. Special thanks to xclin <xclin<> cs dot nctu dot edu dot tw>
who sent fix for receiving VLAN oversized frames.
unneeded for legacy hardware.
Also remove some TSO related cruft.
Add some watchdog_time setting that was missing, thanks
to Mikolaj Golub for pointing that out.
* WPA-None requires ap_scan=2:
The major difference between ap_scan=1 (default) and 2 is, that no
IEEE80211_IOC_SCAN* ioctls/functions are called, though, there is a
dependency on those. For example the call to wpa_driver_bsd_scan()
sets the interface UP, this never happens, therefore the interface
must be marked up in wpa_driver_bsd_associate(). IEEE80211_IOC_SSID
also is not called, which means that the SSID has not been set prior
to the IEEE80211_MLME_ASSOC call.
* WPA-None has no support for sequence number updates, it doesn't make
sense to check for replay violations..
* I had some crashes right after the switch to RUN state, issue is
that sc->sc_lastrs was not yet defined.
Approved by: rpaulo (mentor)
MFC after: 3 weeks
StarCat systems which provides time-of-day services for both as well as
console service for Serengeti, i.e. Sun Fire V1280. While the latter is
described with a device type of serial in the OFW device tree, it isn't
actually an UART. Nevertheless the console service is handled by uart(4)
as this allowed to re-use quite a bit of MD and MI code. Actually, this
idea is stolen from Linux which interfaces the sun4v hypervisor console
with the Linux counterpart of uart(4).
set, it make sense to actually initialize that array. This fixes some
issues with 4965 adapters where the TX power is crucial.
This got lost somewhere while merging with the OpenBSD code.
Approved by: rpaulo (mentor)
Obtained from: OpenBSD
MFC after: 2 weeks
* Enable DC calibration and crystal calibration on Centrino Advanced-N
6250 parts.
* Workaround for a HW bug (does not affect 4965AGN) that may sporadically
affect latency under some rare circumstances. From a similar commit to
iwlwifi.
* Update sensitivity settings for 5000 series to workaround a performance
bug in the DSP (1000 is not affected so we keep the old values for 5000).
* Update sensitivity settings for 6000 series.
* Set differential gains on 6250 too (but use a 1.0 factor, not 1.5).
* Init OFDM sensitivity with min value (which depends on the chip)
instead of hardcoding it to 90.
* Read calibration version from ROM and set IWN_GP_DRIVER_CALIB_VER6
bit on 6x50 if version >= 6.
Approved by: rpaulo (mentor)
Obtained from: OpenBSD
MFC after: 2 weeks
- code flow in handler could let interrupt be
reenabled when not wanted.
- change where the RX lock is taken to improve
performance.
- adapter->msix is true for MSI systems also,
it needs to explicitly test for 82574, good one :)
- add CRC stripping to the RX side, this was handled
by some obscure code in rxeof previously, its easier
to simply have the hardware strip it now.
- Add back an ALTQ change that slipped between the cracks
- Add an update to the watchdog_time in the xmit code, not
doing this in ixgbe caused problems, think its needed here
as well.
VLAN HWFILTER from being used by default, this breaks
stacked pseudo devices, and as it turns out, also breaks
virtual machines that happen to use VLANS (didn't know that
before :). Put the fix back into the em driver, and for good
measure add the same code to the igb driver where it should
have been anyway.
Just relying on status LE ownership of status block seems to cause
poor performance. Always read current status index register first
and then check status ownership as we had before. Accessing status
index register seems to trigger immediate status update if
controller have pending status updates.
MFC after: 1 week
Reported by: Andre Albsmeier <Andre.Albsmeier <> siemens dot com>
Tested by: Andre Albsmeier <Andre.Albsmeier <> siemens dot com>
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
- Added some new debug helper routines to systcl.
- Fixed many of the style(9) violations that have crept into the code
due to my use of a "smart" editor.
MFC after: 2 weeks
