using a cardbus based system with pccbb providing the pcic interface).
Something isn't quite right.. when the driver allocates and activates
its resources, the IO space that was requested reads as all zeros (versus
the original 0xff's as it normally is when there is no device responding).
Also, deactivate the resources before releasing them. OLDCARD doesn't
seem to care but NEWCARD/CARDBUS get rather unhappy if you release
a resource that hasn't been deactivated yet.
Make pcic_p.c only compile with oldcard kernels.
(identified by the IO map being 256 bytes long instead of 128)
This chip works very unreliably on my Lanner embedded PC with the rl driver.
Lots of watchdog timeouts or poor performance.
Forcing the media type to 10 Meg (ifconfig rl0 media 10baseT/UTP) is a good
workaround.
This looks very similar to the problem reported in PR kern/18790
It is interesting to note that the linux driver has lots of special
case code for this chip.
* Some dummynet code incorrectly handled a malloc()-allocated pseudo-mbuf
header structure, called "pkt," and could consequently pollute the mbuf
free list if it was ever passed to m_freem(). The fix involved passing not
pkt, but essentially pkt->m_next (which is a real mbuf) to the mbuf
utility routines.
* Also, for dummynet, in bdg_forward(), made the code copy the ethernet header
back into the mbuf (prepended) because the dummynet code that follows expects
it to be there but it is, unfortunately for dummynet, passed to bdg_forward
as a seperate argument.
PRs: kern/19551 ; misc/21534 ; kern/23010
Submitted by: Thomas Moestl <tmoestl@gmx.net>
Reviewed by: bmilekic
Approved by: luigi
struct sigframe. We need more than only the signal context.
o Properly convert the signal mask when setting up the signal
frame in linux_sendsig and properly convert it back in
linux_sigreturn.
Do some cleanups and improve style while here.
can unload. Doing so leaves the linuxulator in a crippled
state (no ioctl support) when Linux binaries are run at
unload time.
While here, consistently spell ELF in capitals and perform
some minor style improvements.
ELF spelling submitted by: asmodai
is already in 32-bit mode, we need to be able to detect this and still
read the chip ID code. Detecting 32-bit mode is actually a little
tricky, since we want to avoid turning it on accidentally. The easiest
way to do it is to just try and read the PCI subsystem ID from the
bus control registers using 16-bit accesses and compare that with the
value read from PCI config space. If they match, then we know we're in
16-bit mode, otherwise we assume 32-bit mode.
instead of ng_send_data().
The latter could lead to running the IP stack at splimp
instead of splnet, (among other problems) (that MAY be safe
but I wouldn't count on it).
Noticed while preparing a new set of netgraph stuff.
counter register in-CPU.
This is to be used as a fast "timer", where linearity is more important
than time, and multiple lines in the linearity caused by multiple CPUs
in an SMP machine is not a problem.
This adds no code whatsoever to the FreeBSD kernel until it is actually
used, and then as a single-instruction inline routine (except for the
80386 and 80486 where it is some more inline code around nanotime(9).
Reviewed by: bde, kris, jhb
a kevent upon completion of the I/O. Specifically, introduce a new type
of sigevent notification, SIGEV_EVENT. If sigev_notify is SIGEV_EVENT,
then sigev_notify_kqueue names the kqueue that should receive the event
and sigev_value contains the "void *" is copied into the kevent's udata
field.
In contrast to the existing interface, this one: 1) works on
the Alpha 2) avoids the extra copyin() call for the kevent because all
of the information needed is in the sigevent and 3) could be
applied to request a single kevent upon completion of an entire lio_listio().
Reviewed by: jlemon
- move the call to cia_init_sgmap() to after we've determined if we're a pyxis
- convert needed splhigh() in cia_sgmap_invalidate_pyxis() to disable_intr()
Previously, any isa DMA on a pyxis based machine would cause a panic
in cia_sgmap_invalidate_pyxis() because the pyxis workaround was never
setup.
- while i'm at it, convert needed splhigh() in cia_swiz_set_hae_mem to
disable_intr()
in the face of multiple processes doing massive numbers of filesystem
operations. While this patch will work in nearly all situations, there
are still some perverse workloads that can overwhelm the system.
Detecting and handling these perverse workloads will be the subject
of another patch.
Reviewed by: Paul Saab <ps@yahoo-inc.com>
Obtained from: Ethan Solomita <ethan@geocast.com>
could not compress into clusters. This could result in lots of
wasted clusters while recieving small packets from an interface
that uses clusters for all it's packets.
Patch is partially from BSDi (limiting the size of the copy) and
based on a patch for 4.1 by Ian Dowse <iedowse@maths.tcd.ie> and
myself.
Reviewed by: bmilekic
Obtained From: BSDi
Submitted by: iedowse
