lengths for CONNECT_REQ and CONNECT_IND are incorrect, which causes
dialouts to fail after certain error situations (an invalid -- not
wrong! -- number has been dialed). Since these messages are tagged as
too short, the device reads trailing garbage as the B protocol
parameters; this is OK as long as the garbage consists of zero bytes,
which it usually does, except after the said error.
Another change we have taken into use is to send an explicit Q.850
"normal call clearing" code when a call is ignored using PRI equipment
(specifically AVM T1); the CAPI pseudo-code for ignore, 1, translates
into something at least Ericsson exchanges interpret oddly (message
"this area is not reachable from your number"). NCCLR makes the exchange
give a busy signal, which is the behaviour at least we prefer
(conceivably, the ignore code could be made a sysctl variable).
The attached patch corrects the message length issue. It also includes a
somewhat unpretty solution for the PRI ignore code (if device's number
of channels equals 30, assume PRI and send NCCLR, otherwise send CAPI
ignore). Tested using AVM B1 PCI and T1 PCI.
Submitted by: Juha-Matti Liukkonen <jml@cubical.fi>
Reviewed by: hm
MFC after: 1 month
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
Add a CAPI (hardware independent) driver i4bcapi(4) and hardware driver
iavc (4) to support active CAPI-based BRI and PRI cards (currently AVM
B1 and T1 cards) to isdn4bsd.
Reviewed by: hm
Bug in i4btel driver read routine corrected. The conditions in the
while() clause caused the receive queue to be referenced before checking
if a channel is connected, leading to kernel panic (do a 'dd
if=/dev/i4btel0 of=/dev/null' on an unconnected tel device, panic will
follow). Correction was to reorder the while clause conditions to check
for connectedness first.
Merge rev's 1.65 and 1.66 from sys/net/if_spppsubr.c (implement the
`restart' option, and fix a blatant bug with PAP authentication).
The i4b implementation of this file should be merged back, but for now,
we need this here as well.
Reviewed by: gj
There are two 3rd party code chunks using this still - the IPv6 stuff and
i4b. Give them a private copy as an alternative to changing them too much.
XXX sys/kernel.h still has a #include <sys/module.h> in it. I will be
taking this out shortly - this affects a number of drivers.
- remove all occurances of FLAG_XXX values and replace with CARD_TYPEP_XXX
- remove sc_flag from isic softc and replace it with sc_cardtyp
remove some left over redundant definitions from isic and i4b_l1.h
remove left over cvs id from i4b cvs repository
broken the handling of uncompressed VJ packets. The attached diff should
hopefully fix that.
Submitted by: Thomas Moestl <tmoestl@gmx.net>
Reviewed by: Sergio de Souza Prallon <prallon@tmp.com.br>
from Traverse Technology and also the Teles PCI-TJ cards both based on the
chipset combination of the Siemens ISAC and the TJNet Tiger300/320 chips.
The itjc/i4b_hdlc.h file will hopefully soon be merged with the file
/usr/src/sys/i4b/layer1/i4b_hdlc.h.
Submitted by: Sergio de Souza Prallon <prallon@tmp.com.br>
enables the driver to work on current (I have not tested the isa part fully,
but I suppose it should work). The patching from jlemon caused a crash at
probe time. This is probably my fault not having added a comment for
"RESET_SOFT" saying: "this resets all!".
Submitted by: Hans Petter Selasky <hselasky@c2i.net>
avma1pp_attach_avma1pp, since the former may be called multiple
times and we only want to initialize the mutex once.
Submitted by: Thomas Moestl <tmoestl@gmx.net>
This version is functional and is aproaching solid..
notice I said APROACHING. There are many node types I cannot test
I have tested: echo hole ppp socket vjc iface tee bpf async tty
The rest compile and "Look" right. More changes to follow.
DEBUGGING is enabled in this code to help if people have problems.
format version number. (userland programs should not need to be
recompiled when the netgraph kernel internal ABI is changed.
Also fix modules that don;t handle the fact that a caller may not supply
a return message pointer. (benign at the moment because the calling code
checks, but that will change)
This clears out my outstanding netgraph changes.
There is a netgraph change of design in the offing and this is to some
extent a superset of soem of the new functionality and some of the old
functionality that may be removed.
This code works as before, but allows some new features that I want to
work with and evaluate. It is the basis for a version of netgraph
with integral locking for SMP use.
This is running on my test machine with no new problems :-)
before adding/removing packets from the queue. Also, the if_obytes and
if_omcasts fields should only be manipulated under protection of the mutex.
IF_ENQUEUE, IF_PREPEND, and IF_DEQUEUE perform all necessary locking on
the queue. An IF_LOCK macro is provided, as well as the old (mutex-less)
versions of the macros in the form _IF_ENQUEUE, _IF_QFULL, for code which
needs them, but their use is discouraged.
Two new macros are introduced: IF_DRAIN() to drain a queue, and IF_HANDOFF,
which takes care of locking/enqueue, and also statistics updating/start
if necessary.
newbus for referencing device interrupt handlers.
- Move the 'struct intrec' type which describes interrupt sources into
sys/interrupt.h instead of making it just be a x86 structure.
- Don't create 'ithd' and 'intrec' typedefs, instead, just use 'struct ithd'
and 'struct intrec'
- Move the code to translate new-bus interrupt flags into an interrupt thread
priority out of the x86 nexus code and into a MI ithread_priority()
function in sys/kern/kern_intr.c.
- Remove now-uneeded x86-specific headers from sys/dev/ata/ata-all.c and
sys/pci/pci_compat.c.
cloning infrastructure standard in kern_conf. Modules are now
the same with or without devfs support.
If you need to detect if devfs is present, in modules or elsewhere,
check the integer variable "devfs_present".
This happily removes an ugly hack from kern/vfs_conf.c.
This forces a rename of the eventhandler and the standard clone
helper function.
Include <sys/eventhandler.h> in <sys/conf.h>: it's a helper #include
like <sys/queue.h>
Remove all #includes of opt_devfs.h they no longer matter.
Remove old DEVFS support fields from dev_t.
Make uid, gid & mode members of dev_t and set them in make_dev().
Use correct uid, gid & mode in make_dev in disk minilayer.
Add support for registering alias names for a dev_t using the
new function make_dev_alias(). These will show up as symlinks
in DEVFS.
Use makedev() rather than make_dev() for MFSs magic devices to prevent
DEVFS from noticing this abuse.
Add a field for DEVFS inode number in dev_t.
Add new DEVFS in fs/devfs.
Add devfs cloning to:
disk minilayer (ie: ad(4), sd(4), cd(4) etc etc)
md(4), tun(4), bpf(4), fd(4)
If DEVFS add -d flag to /sbin/inits args to make it mount devfs.
Add commented out DEVFS to GENERIC
Use Warner Losh's "hint" driver to decode ascii strings to fill the
resource table at boot time.
config(8) no longer generates an ioconf.c table - ie: the configuration
no longer has to be compiled into the kernel. You can reconfigure your
isa devices with the likes of this at loader(8) time:
set hint.ed.0.port=0x320
userconfig will be rewritten to use this style interface one day and will
move to /boot/userconfig.4th or something like that.
It is still possible to statically compile in a set of hints into a kernel
if you do not wish to use loader(8). See the "hints" directive in GENERIC
as an example.
All device wiring has been moved out of config(8). There is a set of
helper scripts (see i386/conf/gethints.pl, and the same for alpha and pc98)
that extract the 'at isa? port foo irq bar' from the old files and produces
a hints file. If you install this file as /boot/device.hints (and update
/boot/defaults/loader.conf - You can do a build/install in sys/boot) then
loader will load it automatically for you. You can also compile in the
hints directly with: hints "device.hints" as well.
There are a few things that I'm not too happy with yet. Under this scheme,
things like LINT would no longer be useful as "documentation" of settings.
I have renamed this file to 'NOTES' and stored the example hints strings
in it. However... this is not something that config(8) understands, so
there is a script that extracts the build-specific data from the
documentation file (NOTES) to produce a LINT that can be config'ed and
built. A stack of man4 pages will need updating. :-/
Also, since there is no longer a difference between 'device' and
'pseudo-device' I collapsed the two together, and the resulting 'device'
takes a 'number of units' for devices that still have it statically
allocated. eg: 'device fe 4' will compile the fe driver with NFE set
to 4. You can then set hints for 4 units (0 - 3). Also note that
'device fe0' will be interpreted as "zero units of 'fe'" which would be
bad, so there is a config warning for this. This is only needed for
old drivers that still have static limits on numbers of units.
All the statically limited drivers that I could find were marked.
Please exercise EXTREME CAUTION when transitioning!
Moral support by: phk, msmith, dfr, asmodai, imp, and others
ioccom.h defines only implementation detail, and should therefore
only be included from the #include which defines the ioctl tags,
in other words: never include it from *.c
particular ISDN card with the 2nd IDE controller and/or other cards
depending on configuration.
The amount of i/o ports allocated are reduced from 0x40 per range to
0x20 per range.
Submitted by: Andrew Gordon <arg@arg1.demon.co.uk>
Approved by: jkh
Enable the driver in sys/conf/files.i386.
In isa/isavar.h increase ISA_NPORT from 32 to 50. This is required
because this brain-damaged card maps 49 (!) port ranges. This does
not have a negative impact because this value only specifies the maximum
number of entries in a linked list and not the size of an array which
is allocated in all drivers.
The register/fifo access routines were not newbus-ified because
1) I knew that the old code worked and is simpler and more efficient
2) the if_ed driver does something similar and
3) the newbus macros collapse to inb/outb anyway.
Reviewed and tested by: hm
Approved by: jkh
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it. Driver writers can do
this if it's not defined. (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
1:
s/suser/suser_xxx/
2:
Add new function: suser(struct proc *), prototyped in <sys/proc.h>.
3:
s/suser_xxx(\([a-zA-Z0-9_]*\)->p_ucred, \&\1->p_acflag)/suser(\1)/
The remaining suser_xxx() calls will be scrutinized and dealt with
later.
There may be some unneeded #include <sys/cred.h>, but they are left
as an exercise for Bruce.
More changes to the suser() API will come along with the "jail" code.
Because the Fritz!Card PCMCIA stuff is also affected, this includes the fix
from PR kern/10278 submitted by Udo Schweigert (udo.schweigert@mchp.siemens.de).
PR: kern/10278
ISDN4BSD is the work of our brand-new comitter: Hellmuth Michaelis,
who has done a tremendous amount of work to bring us this far.
There are still some outstanding issues and files to bring into
the tree, and for now it will be needed to pick up all the extra
docs from the isdn4bsd release.
It is probably also a very good idea to subscribe to the isdn@freebsd.org
mailing list before you try this out.
These files correspond to release "beta Version 0.70.00 / December
1998" from Hellmuth.
