if a device has vchans already but they are all busy, allocate another one
at open() time, up to a maximum of hw.snd.maxvchans.
when creating/destroying vchans, don't make/remove a devnode for the
first/last one as it replaces a hardchan.
functions in ifconfig. "ifconfig an0" should output the correct
status now. Also, make the read and write functions both more
robust and more consistant. This should stop most of the incorrect
size complaints and eliminate the possiability of panics from firmware
that increases resource sizes.
PR: kern/27826
Reviewed by: imp, jlemon
Submitted by: Doug Ambrisko <ambrisko@ambrisko.com>
David Wolfskill <dhw@whistle.com>
. staticize out_fdc(), there's no longer an ft(4) driver sharing its use
. remove in_fdc(), has been used by ft(4) last time, long since obsoleted
by fd_in()
. move the declaration of fd_clone() to where most of the other function
declarations are
. de-__P()ify fd_clone(), it's been the only _P()ed function in the
entire file
something: offset into the first mbuf of the target chain before copying
the source data over.
Make drivers using m_devget() with a first argument "data - ETHER_ALIGN"
to use the offset argument to pass ETHER_ALIGN in. The way it was previously
done is potentially dangerous if the source data was at the top of a page
and the offset caused the previous page to be copied (if the
previous page has not yet been appropriately mapped).
The old `offset' argument in m_devget() is not used anywhere (it's always
0) and dates back to ~1995 (and earlier?) when support for ethernet trailers
existed. With that support gone, it was merely collecting dust.
Tested on alpha by: jlemon
Partially submitted by: jlemon
Reviewed by: jlemon
MFC after: 3 weeks
the console device was open. At other times, the interrupts that
are used to detect the break signal or ~^B sequence were disabled,
so these events would not be noticed until the next open (e.g. the
next kernel printf). This was mainly a problem while there was no
getty running on the console, such as during bootup or shutdown.
For serial consoles with break-to-debugger support, we now enable
the generation of interrupts at attach time, and we leave them
enabled while the device is closed.
Reviewed by: bde (I've since made chages as per his suggestions)
via the new DIGIIO_SETALTPIN ioctl, and allow the port's ALTPIN setting
to be queried via DIGIIO_GETALTPIN.
The initial state and lock devices are normally used to set and/or
lock ALTPIN settings although the device itself may also be used.
ALTPIN settings are applied per-device and apply to both the callin
and callout device at the same time.
converting from the old external mbuf buffer code to the new (with the
MEXTADD() macro). Also free free list memory correctly in
foo_free_jumbo_mem() routines: grab the head of the list, then
remove it, _then_ free() it.
This fixes the memory corruption problem I've been chasing in the level 1
driver.
1: most drivers are sensitive to timing, and
2: the handlers are MPSAFE and need a chance to get into the kernel
before some other non-mpsafe handler blocks the ithread on Giant in
shared irq cases.
Reviewed by: cg (in principle)
worked before.
mixer, dsp and sndstat are seperate devices - give them their own cdevsws
instead of demuxing requests sent to a single cdevsw.
use the si_drv1/si_drv2 fields in dev_t structures for holding information
specific to an open instance of mixer/dsp.
nuke /dev/{dsp,dspW,audio}[0-9]* links - this functionality is now provided
using cloning.
various locking fixes.
ports later on.
This includes the basic MI interface routines as well as a console driver.
The MD code is kept in the MD directories.
Reviewed by: obrien
built in, or as an addon card (My Japanese isn't quite good enough to
know which). [FreeBSD98-testers 5098] contains all the details.
Submitted by: Kawanobe Koh-san <kawanobe@st.rim.or.jp>
The DP83820/83821 has an undocumented limitation concerning jumbo frames
and TX checksum offload. In order for TX checksum offload to work, the
outgoing frame must fit entirely within the TX FIFO, which is 8192 bytes
in size. This isn't a problem, until you try to send a 9000-byte frame,
at which point the TX DMA engine goes to sleep. It turns out that if
you want to send a jumbo frame larger than 8170 bytes (8192 - 64), you
have to turn off the TX checksum support.
As a workaround, I changed nge_ioctl() so that if the user selects an
MTU larger than 8152 bytes, we clear the if_hwassist flags. The flags
will be set again once the MTU is reduced to a smaller value.
we want the checksums calculated on a per-packet basis using control bits
in the extsts field of the DMA descriptor structure. For TX, the chip
seems to want these bits set in the field of the first descriptor in
a fragment chain, not the last.
