- Don't return a negative errno when using an unknown ioctl() on a
pseudo-terminal master device. Be sure to convert ENOIOCTL to ENOTTY,
just like the TTY layer does.
- Even though we should return st_rdev of the master device node when
emulating pty(4) devices, FIODGNAME should still return the name of
the slave device. Otherwise ptsname(3) and ttyname(3) return an
invalid device name.
values like 0x80 or 0x40 into a uint8_t foo:1 bitfield. This would
result in the bit always being 0. One of these caused a warning for
overflow (one that was 0x80), but the other didn't. They were both
wrong.
This is why I hate code that mixes c struct bitfields and #defines.
The rest of the fields accessed by the program should be audited.
Not enough space in user-land buffer is not an error, userland
will read further until eof is reached. So instead of propagating
-1 to caller we convert it to zero/success.
cd9660 code works exactly the same way.
PR: kern/78987
Reviewed by: jhb (mentor)
Approved by: jhb (mentor)
This is triggered only if BIOS configures ACPI_BITREG_BUS_MASTER_RLD
aka BRLD_EN_BM to 1.
Rationale:
1. we do not support C3 on PIIX4E
2. bus master activity need not break out of C2 state
3. because of CPU_QUIRK_NO_BM_CTRL quirk we may reset bus master
status which would result in immediate break out from C2
So if you have seen
cpu0: too many short sleeps, backing off to C1
with this chipset before you may want to try cx_lowest of C2 again.
Reviewed by: rpaulo (mentor), njl
Approved by: rpaulo (mentor)
ata_detach() to implement IOCATAATTACH/IOCATADETACH ioctls.
This will permit channel drivers to properly shutdown port hardware on channel
detach and init it on attach.
channel modes:
o usurp 'h' mode flag for half-width channels
o add 'q' mode flag for quarter-width channels
o rewrite rate parameter parsing to handle fractional values
o merge mode loops to eliminate ordering assumptions
o replace 0x80 with IEEE80211_RATE_MCS
and xmit parameters. This makes it possible to use tdma on fractional
channels.
o add IEEE80211_MODE_HALF and IEEE80211_MODE_QUARTER; note these are
band-agnostic (may need revisiting)
o setup all default rates in ic_sup_rates instead of doing it only
for active modes; we need these to calculate the default tx parameters
which are not recalculated after a regulatory update (can't just
recalculate after installing a new channel list because we might
clobber user settings)
o remove special case code in ieee80211_get_suprates; this is now
a candidate for an inline or removal
o add various entries for new modes (roaming+tx params, wme, rate
mapping, scan set setup, country ie construction, tdma, basic rates)
Note these modes are intentionally not visible through if_media.
parameters for IEEE80211_IOC_ROAM and IEEE80211_IOC_TXPARAMS; this
lets us add more modes and still have old apps work
o consolidate loops to remote assumptions about mode ordering
o mark phy type to indicate 1/2 or 1/4-rate operation
o use phy type instead of channel attributes to identify 1/2 and 1/4-rate
operation
o general cleanup of code including move phy constants to ah_internal.h
Eventually this code should go away and we should use the net0211 equivalents.
the old TTY implementation; however, take a cut at stripping its
optional Giant-protected code paths enabled using debug.cx.mpsafenet,
which will no longer work once IFF_NEEDSGIANT is removed.
struct passwd. This is not the case when sizeof(unsigned long) !=
sizeof(time_t). Write a dinky function to do the assignment instead
of relying on the punning. This does slow things down a little (1
extra function call, 11 pointer or int assignments), but is much safer
and machines have been fast enough since the mid 1990s that nobody
will notice the difference.
time_t is a 64-bits int on arm and mips. Before this change, arm was
silently broken. I guess there aren't that many ARM machines running
master YP domain servers. :)
The client side doesn't assume this type punning, so it doesn't need
to be fixed.
join allocate() and dmainit() atapci subdriver's channel initialization
methods into single ch_attach() method.
As opposite to ch_attach() add new ch_detach() method to deallocate/disable
channel.
members for a kinfo entry on a process-wide system.
- Use the newly introduced function in order to fix cases like
KERN_PROC_PROC where aggregating stats are broken because they just
consider the first thread in the pool for each process.
(Note, additively, that KERN_PROC_PROC is rather inaccurate on
thread-wide informations like the 'state' of the process. Such
informations should maybe be invalidated and being forceably discarded
by the consumers?).
- Simplify the logic of sysctl_out_proc() and adjust the
fill_kinfo_thread() accordingly.
- Remove checks on the FIRST_THREAD_IN_PROC() being NULL but add
assertives.
This patch should fix aggregate statistics for KERN_PROC_PROC.
This is one of the reasons why top doesn't use this option and now it
can be use it safely.
ps, when launched in order to display just processes, now should report
correct cpu utilization percentages and times (as opposed by the old
code).
Reviewed by: jhb, emaste
Sponsored by: Sandvine Incorporated
alignment requirement, while rt_msghdr has a 4 byte alignment
requirement. The root cause is that if_msghdr has an struct if_data
which has an 8-byte alignment requirement due to a time_t that's
embedded in it. On MIPS, time_t is a 64-bit number, so must be 64-bit
aligned.
Since we don't access ifm_data.ifi_epoch, a simple cast is all that's
necessary here. It is likely the case that ifi_epoch should *NOT* be
a time_t because it is an uptime (time delta) an not an absolute time
since 1970. u_long is likely sufficient there since that gives an
uptime of 136 years will suffice for the foreseeable future.
it instead of overloading sbp_show_sdev_info().
replace calls to printf with calls to device_printf and cleanup debug
messages
Remove a bit of dead, commented out code.
Reviewed by: scottl(mentor)
MFC after: 2 weeks
