Properly wait for not busy and introduce a timeout for devices not
setting busy (as they should).
Leave a printf in there that states how long the wait was, as I'd like
to get an idea of the variations here. The time needed seems also to be
affected by whether a medium is present or not.
controllers (PDC203** PDC206**).
This also adds preliminary support for the Promise SX4/SX4000 but *only*
as a "normal" Promise ATA controller (ATA RAID's are supported though
but only RAID0, RAID1 and RAID0+1).
This cuts off yet another 5-8% of the command overhead on promise controllers,
making them the fastest we have ever had support for.
Work is now continuing to add support for this in ATA RAID, to accellerate
ATA RAID quite a bit on these controllers, and especially the SX4/SX4000
series as they have quite a few tricks in there..
This commit also adds a few fixes to the SATA code needed for proper support.
This adds support for cardbus ATA/SATA controllers. I get roughly the
same transfer speeds as on true PCI controllers. Nice to be able to add
a couble of "real" disks to a laptop :)
instead of taskqueue_swi. This shaves from 1 to 10% of the overhead.
Overhaul the locking once more, there was a few possible races that
are now closed.
This gives +10% performance on simple tests, so definitly worth it.
A few percent more could be had by not using M_ZERO'd alloc's, but
we then need to clear fields all over the place to be safe, and
that was deemed not worth the trouble (and it makes life dangerous).
of the leftovers from the old version that really doesn't work anymore.
Add a reset function for host-end of the ATA channel. This is needed
for the SiI3112 in order to whack it back to reality if a device
locks up the SATA interface (thereby preventing that we can reset the
device). The result is that ATA now recovers from the timeouts that
happens with the SiI3112A and more or less all disks based on old
PATA electronics with a Marvell PATA->SATA converter. This includes
lots of the popular SATA dongles and the WDC Raptor disks..
in connection with Marvell based SATA->PATA dongles.
The problem was caused by a combination of things working
together to make it hard to spot...
The ATA driver has always started the ATA command, then build
the SG list for DMA and then finally started the DMA engine.
While this is according to specs, it poses a potential
problem as some controllers apparently do not allow for unlimitted
time between starting the ATA command and starting the DMA engine.
At about the same time as ATAng was committed there were lots
of other changes applied, some of which was locking in parts
that causes the busdma load functions to take significantly
longer to load the SG list.
This pushed the time spent between starting the ATA command and
starting the DMA engine over the hill for some controllers
(especially the Silicon Image DS3112a) and caused what looked
like lost interrupts.
The solution is to get all the SG list work or rather all
busdma related stuff done before we even try to start anything.
This has the nice side effect of seperating busdma out the
way it should be, so the working of the ATA machinery is not
cluttered up with busdma droppings, making the code easier
to read and understand.
was that accessing the status reg could occour too fast, confusing
the logic in the flash part. Could not have been located without:
HW donated by: Jonas Bülow <jonas@servicefactory.se>
Restructure the way ATA/ATAPI commands are processed, use a common
ata_request structure for both. This centralises the way requests
are handled so locking is much easier to handle.
The driver is now layered much more cleanly to seperate the lowlevel
HW access so it can be tailored to specific controllers without touching
the upper layers. This is needed to support some of the newer
semi-intelligent ATA controllers showing up.
The top level drivers (disk, ATAPI devices) are more or less still
the same with just corrections to use the new interface.
Pull ATA out from under Gaint now that locking can be done in a sane way.
Add support for a the National Geode SC1100. Thanks to Soekris engineering
for sponsoring a Soekris 4801 to make this support.
Fixed alot of small bugs in the chipset code for various chips now
we are around in that corner anyways.
