Get counting volume I/Os right.
launch_requests: Be macho, throw away the safety net and walk the
tightrope with no splbio().
Add some comments explaining the smoke and mirrors.
Remove some redundant braces.
sdio: Set the state of an accessed but down subdisk correctly. This
appears to duplicate an earlier commit that I hadn't seen.
Get counting volume I/Os right.
Count buffer sizes correctly for architectures where ints are not 32 bits.
complete_rqe: Move decrementing active count until after call to
complete_raid5_write, thus possibly avoiding a race condition.
Suggested-by: dillon
Rename user bp to ubp to avoid confusion.
Tidy up comments.
a struct buf. Don't try to examine B_ASYNC, it is a layering violation
to do so. The only current user of this interface is vn(4) which, since
it emulates a disk interface, operates on struct bio already.
ioccom.h defines only implementation detail, and should therefore
only be included from the #include which defines the ioctl tags,
in other words: never include it from *.c
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
coming later this week. Mitsuru IWASAKI provided a patch to -mobile which
I used to make sure I was doing the right thing but only a small part of
the actual patch was used.
that fails to proberly close the disk.
The problem seems to be that the HP burners sometimes return
ready when they actually are not, the solution is to not use
immediate mode on the closing commands. This is suboptimal
for real burners, in that they now hog the ATA bus for possibly
minutes, where its really not nessesary, *sigh*.
not u_long. On i386's with 64-bit longs, returning u_longs indirectly
in (more than) the space reserved for uintptr_t's tended to corrupt the
previous frame pointer in the stack frame, so it was not easy to debug.
The type mismatches are hidden by the bogus cast in DEVMETHOD().
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
53C810 non 'A', 53C815 and 53C825 non 'A' are now
attached by the driver (by default).
The driver uses a different SCRIPTS set based on
MEMORY MOVE instructions for these chips.
2 SCRIPTS sets (firmwares) numbered #1 and #2 are
used for the whole support of the 53C8XX family
to get possible:
- FW #1 : Only based on MEMORY MOVE instructions.
Selected for 810, 815, 825.
- FW #2 : LOAD/STORE based. This is the firmware
also used by previous driver versions.
Selected for other chips.
When both `ncr' and `sym' are configured, `sym'
will now attach all the 53C8XX devices by default.
Previous balancing between `ncr' and `sym' can be
preserved by:
- Either editing sym_conf.h and commenting the
following compile option:
#define SYM_CONF_GENERIC_SUPPORT
(This also saves about 3.5Kb of kernel memory).
- Or setting kernel config option
SYM_SETUP_LP_PROBE_MAP to 64 (bit 0x40)
first. This will fix a few cards that hang on the WD probe. He tells
me that PAO went one step farther and removed the WD proble completely
and none of the cards in the 2.x database broke in PAO3. Since I'm
more conservative in this code, I'm just swapping the order, which he
said also fixed his problem.
Reviewed by: mdodd, iwasaki
Submitted by: sanpai@sanpai.org
The makefile contains a reference to /sys/dev/ppbus. What really should
be done is copy the header files to /usr/include/sys/dev/ppbus.
PR: kern/16767
Submitted by: Jin Guojun (FTG staff) <jin@gracie.lbl.gov>
This driver should support both the SSI (V.35 etc) E1/T1 unchannelized,
DS3 and HSSI cards. Only tested on the SSI card.
More info at: http://www.lanmedia.com
Thanks to LanMedia for donating two LMC1000P cards.
if_de.c driver modified by: LanMedia
NetGraphification by: Stephen Kiernan <sk-ports@vegamuse.org>
in struct bio. Eventually, bio_offset will probably obsolete the
bio_blkno and bio_pblkno fields.
Remove the special hack in atapi-cd.c to determine of bio_offset was valid.
that seems to be working (I have a MF card that has a 336 modem and
ethernet that the probe routine finds, but the attach fails on because
pccardd doesn't do what you'd like with MF cards all the time).
