sx driver), change a magic value in the PLX bridge chip. Apparently later
builds of the PCI cards had corrected values in the configuration eeprom.
This change supposedly fixes some pci bus problems.
hack means you can get the units and flags to match up more easily with
serial consoles on machines with acpi tables that cause the com ports
to be probed in the wrong order (and hence get the wrong sio unit number).
This replaces the common alternative hack of editing the code to comment
out the acpi attachment. This could go away entirely when device wiring
patches are committed.
stomping on the units intended for the motherboard sio ports. This is
no real substitute for the not-yet-committed device wiring enhancements.
Code taken from sio's pci attachment.
Intel CPUs with family 0x6, model 0xE and later (i.e., Intel Core(TM))
have a PMC architecture that differs somewhat from previous CPUs in
family 0x6. Even though the basic programming model is similar, the
documented set of legal values that may be loaded into their PMC MSRs
differs from that of the previous PMCs in family 0x6 and reusing bit
values valid for the older PMCs could result in undefined behaviour in
the general case.
T_DIRECT filtering so that disk drives can be attached via the
pass driver. Add CAM locking. Don't mark CAM commands as SG64
since the hardware isn't designed to deal with 64-bit passthru
commands. Hopefully the bounce buffer changes that were done
for the management/ioctl interface are robust enough to handle
this deficiency for CAM as well.
- Enable pcbeep control for Acer + ALC268 (nid 29). Give enough (fake)
hints so the parser will grab it and allocate "speaker" control.
- Fix regression while preparing DAC and ADC for multichannel
format. Since playback policy is to output to every possible path,
ensure that each DAC is started.
Reported / Tested by: Guy Brand
The call should happen with the driver lock held. We don't hold the driver
lock in newstate as it's a separate thread where we can't sleep (and we only
call wpi_cmd in async mode).
Discovered By: Attillo's callout rework
Approved By: mlaier (comentor)
o Acer Aspire 4520 laptop
- jack sensing / automute
o Toshiba Satellite A135-S4527 laptop
- jack sensing / automute
Tested by: lioux
o Apple Macbook 3 (is it?)
- require gpio0 (for speakers) and ovref50 (for headphone)
to make it works
- jack sensing / automute
Tested by: Ed Schouten
* Add Nvidia MCP67 controller ids.
* Be sensible about simmilar controller with multiple pci ids.
* Connect unused DAC/ADC to stream#0 rather than forcing each of them
managing their own stream.
MFC after: 3 days
- Bring HEAD up to the latest shared code
- Fix TSO problem using limited MSS and forwarding
- Dual lock implementation
- New device support
- For my ease, this code can compile in either 6.x or later
- brings this driver in sync with the 6.3
only at address 0 which is supposed to be the only valid phy address
on Marvell PHY. The more correct solution would be masking PHY
address ranges allowable in PHY probe routine. Unfortunately,
FreeBSD has no way to retrict the PHY address ranges or to pass special
flags to PHY driver.
This change assumes that PHY hardwares attached to msk(4) would be
Marvell made 88E11xx PHY.
With this changes the phantom phys attached on 88E8036(Yukon FE)
should disappear.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
only 4KB SRAM.
o Rework setting Tx/Rx RAM buffer size. Give receiver 2/3 of memory
and round it down to the multiple of 1024. The RAM buffer size of
Yukon II should be multiple of 1024. This fixes bogus RAM buffer
configuration used in Yukon FE.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
publicly available datasheet for Yukon II and don't know what
bug/workaround exist for the specific hardware revision. Also I don't
think the vendor will release hardware errata in near future.
The hardware feature lists were not used at all except setting water
mark registers. Since msk(4) should know exact chip model/revision
number to decide which hardware capability could be used the extra
feature lists were redundant.
o Enable jumbo frame support for EC Ultra and disable jumbo frame
for FE.
o Enable store and forward mode for standard MTU sized frame.
o Enable TSO for EC Ultra. However TSO/checksum offload is disabled
for jumbo frame case. Because EC Ultra can't use store and forward
mode for jumbo frame TSO/checksum offload is not available.
o Adjust Tx GMAC almost empty threshold value and add a jumbo frame
water mark. The maic value was obtained from Marvell's sk98lin
driver.
o Fix EC Ultra chip revision number.
Revert the probe in atapi-cd.c to the old usage now its fixed on AHCI.
THis change also fixes using virtual CD's om fx parallels.
Still leaves the GEOM problem of telling media vs device access apart in the access function.
- Implement timing out of VPD register access.[1]
- Fix an off-by-one error of freeing malloc'd space when checksum is invalid.
- Fix style(9) bugs, i.e., sizeof cannot be followed by space.
- Retire now obsolete 'hw.pci.enable_vpd' tunable.
Submitted by: cokane (initial revision)[1]
Reviewed by: marius (intermediate revision)
Silence from: jhb, jmg, rwatson
Tested by: cokane, jkim
MFC after: 3 days
The register layout is little different from memory-mapped stats
in the previous generation chips. In fact, it is bad because
registers in this range are cleared after reading them.
Reviewed by: scottl
MFC after: 3 days
- Trying to eliminate another racing by replacing the timeout(9) with
callout APIs. In addition to that, the callout_drain() in an_detach()
help us to avoid a possible panic-on-free due to the callout API tries
to lock a destroyed mutex.
- In an_stats_update(), check the return value of an_read_record(). This
should reduce the chance of device removal(PCCARD) panic [2].
- Adding a comment to state the fact that an_stats_update() is now called
via callout(9) with a lock held [2].
Submitted by: jhb [1], ambrisko [2]
Reviewed by: jhb, ambrisko
Reported by: dhw
Tested by: dhw
MFC after: 3 days
priorities of the technologies supported by 802.3 Selector Field
value.
1000BASE-T full duplex
1000BASE-T
100BASE-T2 full duplex
100BASE-TX full duplex
100BASE-T2
100BASE-T4
100BASE-TX
10BASE-T full duplex
10BAST-T
However PHY drivers didn't honor the order such that 100BASE-T4 had
higher priority than 100BASE-TX full duplex. Fix that long standing
bugs such that have PHY drivers choose the highest common denominator
ability.
Fix a bug in dcphy which inadvertently aceepts 100BASE-T4.
PR: 92599
that the driver will handle WEP encryption. However, this does not seem to be
implemented by this driver (or maybe the chipset doesn't support it?)
Removing the flag makes my wpi card work using wpa_supplicant(8) on a
network with 802.1x security (without this change it authenticated fine, but
tcpdump only saw garbage packets)
Reviewed by: benjsc, imp (mentor)
Approved by: imp (mentor), sam
