When SCHEDULER_STOPPED() is true the mtx_owned() call may return
an unexpected and thus meaningless result.
So, in the code paths that can be reached when SCHEDULER_STOPPED() is true
we need to protect the mtx_owned() calls with the SCHEDULER_STOPPED()
checks and ensure that an appropriate branch is taken in each case.
Reviewed by: hselasky
MFC after: 3 months
X-MFC after: r228424
At the moment grab and ungrab methods of all console drivers are no-ops.
Current intended meaning of the calls is that the kernel takes control of
console input. In the future the semantics may be extended to mean that
the calling thread takes full ownership of the console (e.g. console
output from other threads could be suspended).
Inspired by: bde
MFC after: 2 months
This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.
This patch also fixes some build issues in avr32dci.c
MFC after: 2 weeks
It appears this device fails if sent a SYNCHRONIZE_CACHE command, so add
quirk to avoid sending it.
I will follow up with Micron on this issue, and will adjust the quirk if
necessary based on their feedback.
Reviewed by: hselasky@
transfer statemachine. This work is about using a single
state variable instead of multiple state bits as input
for the USB statemachine to determine what to do in the
various parts of the code. No APIs towards USB device
drivers or USB host controller drivers will be changed.
MFC after: 1 month
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
to the kernel's pause() function. The pause() function can now be used
when cold != 0. Also assert that the timeout in system ticks must be
positive.
Suggested by: Bruce Evans
MFC after: 1 week
to kern/subr_bus.c. Simplify this function so that it no longer
depends on malloc() to execute. Identify a few other places where
it makes sense to use device_delete_all_children().
MFC after: 1 week
cp2103 usb-to-serial chip.
- This patch also makes the line status polling asynchronous, to reduce
the time needed to change the GPIO pins.
Submitted by: JD Louw
MFC after: 1 week
- Make it easier to port the USB code to other platforms by only using
one set of memory functions for clearing and copying memory. None of
the memory copies are overlapping. This means using bcopy() is not
required.
- Fix a compile warning when USB_HAVE_BUSDMA=0
- Add missing semicolon in avr32dci.
- Update some comments.
MFC after: 1 week
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
controller.
AX88772B data sheet does not show detailed information about
checksum offloading related things. It seems the controller has
lots of options to support checksum offloading but I failed to
understand why this feature requires so much complex controller
configuration and status bits.
One of major difference between AX88772B and its predecessor is
AX88772B uses a new RX header format when RX checksum offloading is
enabled. It also requires the received length of a frame should be
multiple of 4. Controller will pad necessary bytes to make the
length of received frame to be multiple of 4. It is driver's
responsibility to offset this pad bytes.
Note, AX88772B could be configured to get partial checksum value in
in RX header. This mode uses different RX header format and
currently we don't use that fature.
This change makes axe(4) use driver specific MII attach handler to
override uether(9)'s default MII attach and announce flow-control
capability for AX88178/AX88772A/AX88772B to PHY drivers. It seems
original AX88772 also supports flow-control but I didn't enable it
due to lack of test/access to the controller. The flow-control
threshold parameter is loaded from EEPROM and there is no way to
override this value without reprogramming EEPROM. For AX88772B,
TX/RX IP/TCP/UDP checksum offloading is announced to network stack.
IPv6 and PPPoE checksum offloading is also supported by controller
but we have no way to take advantage of these features.
Driver already knows PHY address so make PHY driver know that
information and remove unnecessary PHY address check used in
miibus_readreg/miibus_writereg callbacks. Also announce AX88178,
AX88772A and AX88772B support VLAN over-sized frame.
While I'm here clean up headers and remove axe_start() in
axe_init() because the link wouldn't be available right after media
change.
handler such that driver can announce interface capabilities and
can do its own MII attach. Currently all USB ethernet controllers
have no way to establish a link with pause capabilities. Lack of
checksum offloading support also was one of reason to bring this
change in.
This change adds a couple of wrappers to USB ethernet drivers
(uether_ifmedia_upd, uether_init and uether_start). All exported
functions in uether has prefix uether_ so I think it's more
consistent to have wrappers that follow the convention.
This change preserves ABI/KPI so it should be safe to merge this
change to stable/8.
While I'm here add missing __FBSDID and clean up headers.
Reviewed by: hselasky
Because driver is accessing a common MII structure in
mii_pollstat(), updating user supplied structure should be done
before dropping a driver lock.
Reported by: Karim (fodillemlinkarimi <> gmail dot com)
on the largest multi-write size.
From the submitter:
==
I looked further into the magic 88-byte threshold after which the bug
occurs. It turns out that figure included the 24-byte tx_desc, and up
to 64 bytes of beacon frame (header+data).
rum_write_multi doesn't seem happy with writing >64 bytes at a time to
the MAC register. If I break it up into separate calls (e.g. bytes
0-63, then bytes 64-65, written at the appropriate offset) I see the
proper beacon frames being transmitted now.
==
Submitted by: Steven Chamberlain <steven@pyro.eu.org>
MFC after: 3 days
Check for this case and just return, so that the UCOM unit number zero is
not accidentially freed.
Submitted by: Danish FreeBSD user at EuroBSDcon 2011
MFC after: 3 days
drivers that only ever attach to a particular MAC driver, i.e. inphy(4),
ruephy(4) and xlphy(4), to the directory where the respective MAC driver
lives and only compile it into the kernel when the latter is also there,
also removing it from miibus.ko and moving it into the module of the
respective MAC driver.
- While at it, rename exphy.c, which comes from NetBSD where the MAC driver
it corresponds to also is named ex(4) instead of xl(4) but that in FreeBSD
actually identifies itself as xlphy(4), and its function names accordingly
for consistency.
- Additionally while at it, fix some minor style issues like whitespace
in the register headers and add multi-inclusion protection to inphyreg.h.
