on-board USB controller. It is not currently enabled because there are
known problems with device communication and until those are fixed I am not
certain that it won't destabilize the system. [1]
o) Add the "cryptocteon" opencrypto device based on the OCF device written by
David McCullough. It is not currently enabled because until support for
saving/restoring coprocessor 2 state on context switch is available, it runs
with interrupts disabled, which tends to pessimize performance over using a
software crypto facility. Tests using this driver which are not negatively
affected by it running with interrupts disabled show it to be substantially
faster than software for large blocks.
Submitted by: hps [1]
library:
o) Increase inline unit / large function growth limits for MIPS to accommodate
the needs of the Simple Executive, which uses a shocking amount of inlining.
o) Remove TARGET_OCTEON and use CPU_CNMIPS to do things required by cnMIPS and
the Octeon SoC.
o) Add OCTEON_VENDOR_LANNER to use Lanner's allocation of vendor-specific
board numbers, specifically to support the MR320.
o) Add OCTEON_BOARD_CAPK_0100ND to hard-wire configuration for the CAPK-0100nd,
which improperly uses an evaluation board's board number and breaks board
detection at runtime. This board is sold by Portwell as the CAM-0100.
o) Add support for the RTC available on some Octeon boards.
o) Add support for the Octeon PCI bus. Note that rman_[sg]et_virtual for IO
ports can not work unless building for n64.
o) Clean up the CompactFlash driver to use Simple Executive macros and
structures where possible (it would be advisable to use the Simple Executive
API to set the PIO mode, too, but that is not done presently.) Also use
structures from FreeBSD's ATA layer rather than structures copied from
Linux.
o) Print available Octeon SoC features on boot.
o) Add support for the Octeon timecounter.
o) Use the Simple Executive's routines rather than local copies for doing reads
and writes to 64-bit addresses and use its macros for various device
addresses rather than using local copies.
o) Rename octeon_board_real to octeon_is_simulation to reduce differences with
Cavium-provided code originally written for Linux. Also make it use the
same simplified test that the Simple Executive and Linux both use rather
than our complex one.
o) Add support for the Octeon CIU, which is the main interrupt unit, as a bus
to use normal interrupt allocation and setup routines.
o) Use the Simple Executive's bootmem facility to allocate physical memory for
the kernel, rather than assuming we know which addresses we can steal.
NB: This may reduce the amount of RAM the kernel reports you as having if
you are leaving large temporary allocations made by U-Boot allocated
when starting FreeBSD.
o) Add a port of the Cavium-provided Ethernet driver for Linux. This changes
Ethernet interface naming from rgmxN to octeN. The new driver has vast
improvements over the old one, both in performance and functionality, but
does still have some features which have not been ported entirely and there
may be unimplemented code that can be hit in everyday use. I will make
every effort to correct those as they are reported.
o) Support loading the kernel on non-contiguous cores.
o) Add very conservative support for harvesting randomness from the Octeon
random number device.
o) Turn SMP on by default.
o) Clean up the style of the Octeon kernel configurations a little and make
them compile with -march=octeon.
o) Add support for the Lanner MR320 and the CAPK-0100nd to the Simple
Executive.
o) Modify the Simple Executive to build on FreeBSD and to build without
executive-config.h or cvmx-config.h. In the future we may want to
revert part of these changes and supply executive-config.h and
cvmx-config.h and access to the options contained in those files via
kernel configuration files.
o) Modify the Simple Executive USB routines to support getting and setting
of the USB PID.
attributes for XKPHYS.
o) Make coprocessor 0 accessor function macros for register+selector registers
take the full name so that e.g. (as done in this commit), prid selector 1
can be written through mips_wr_ebase() rather than mips_wr_prid1().
o) Allow for sign extension of 32-bit segment addresses.
o) Remove an unused MIPS-I register number.
same time.
o) Remove some unused trivial uart functions from octeon_machdep now that the
uart part is fully working and they are unused.
o) Use __func__ instead of __FUNCTION__.
o) Use intr_*() instead of other routines that do the same thing.
o) Remove some duplicate printfs from the Octeon port, as well as duplicate
setting of Maxmem.
o) Use the right frequency divider on Octeon.
o) Use PCPU_GET(cpuid) consistently to get the cpuid of the running core.
o) Remove some unused macros in the Octeon port.
o) Use mips_sync() around use of the global dpcpu, whose value may not be
visible to APs at first.
o) When loading the first thread's stack, use macros to make the code correct
for n64 as well.
o) Remove stub, do-nothing FAU init/enable/disable functions from the RGMX
driver.
pointer, rather than octeon_fpa_alloc.
o) Report half duplex status properly.
o) Do not unconditionally update the last known link status in the softc. If
report_link isn't set, when octeon_rgmx_config_speed is called the first
time it will tell the driver (essentially) that we have already marked the
interface up. Likewise, don't change media speed and duplex if only the
link status is at issue. [1]
o) Remove manual changing of link state and let octeon_rgmx_config_speed do the
heavy lifting. [1]
Reviewed by: [1] imp
Sponsored by: Packet Forensics
o) Properly configure the CAM to handle IFF_PROMISC and note where IFF_ALLMULTI
handling would go if we didn't already force the NIC to receive all
multicast traffic.
Reviewed by: imp
Sponsored by: Packet Forensics
o) Inline octeon_rgmx_mark_ready into octeon_rgmx_init.
o) Add a media status handler that reports link and media status.
o) Set link state when if_init is called.
o) Remove some printfs related to driver state changes.
o) Remove some gratuitous comments.
Reviewed by: imp
Sponsored by: Packet Forensics
than spinning forever. This fixes booting with CF ejected.
NB: I've made the driver pretty chatty about errors in case there's hardware
that operates differently to mine, so we can easily track down any issues.
Reviewed by: imp
Sponsored by: Packet Forensics
redundant implementations.
o) Use ABI, not ISA, to determine address length.
o) Disable and restore interrupts around any operation that uses all 64 bits of
a register. In kernels using the O32 ABI, the upper 32 bits of those
registers is likely to be corrupted by an interrupt.
Sponsored by: Packet Forensics
lacking a copyright/license statement. All these files were in the
Cavium FreeBSD source drop and appear to be written by Cavium (some
are nearly verbatim copies of files from the cnusers' 1.9.0 SDK, which
also uses this copyright).
obio. Take advantage of the fact that obio only really supports uart
at the moment to use the uart bus tag always for IOPORT allocations.
# this needs to be redone to conform to FreeBSD standards and allow for
# additional drivers for SoC hardware to attach
o Force the ebase to be 0x80000000 (the base that we're booted with may
need to be respected in the future).
o Initialize the clock early so we can initialize the console early
o use panic where we can now use it.
o Tag some code for parsing the boot records as belonging in the cavium sdk.
o remove support for booting on ancient boards...
# we make it further in bootstrapping now: interrupts being enabled in the
# uarts are now taking us out, it seems, for reasons unknown.
the Cavium version of the boot loader puts data just after &end, so
our rounding up to the next page in clearing memory overwrote their
data, which meant we'd get a lot of wrong values for parameters to the
system.
While I'm here, remove argc/argv parsing. Those values aren't passed
in via a0 and a1, so it was a guaranted panic on some boards.
Copy the support files for the Octeon 1 CPU from sys/mips/octeon1 on
the projects/mips side to sys/mips/cavium on the head side to conform
to the other vendor code. This code was contributed by Cavium to the
project and forward ported by Warner Losh, with some additional code
from Randal Stewart.
# I'll fix the building problems the move creates in a future commit.
