in the various pci specifications as readonly. vendor, subvendor,
device and subdevice are required to be loaded in hardware by some
means that isn't the system BIOS or other system software (although
some devices do have ways of accomplishing this). class and subclass
are defined to be read-only in section 6.2.1 (v2.2). Apart from the
status register, which we weren't touching, these are the only
read-only registers I could find in the 2.2 spec.
progif is also defined as being read-only in section 6.2.1. However,
the PCI IDE programming document specifically states that some of the
bits are read/write. Since we may have to restore registers before we
have a driver attached, go ahead and restore this one byte when
transitioning between D3 and D0.
The PCI spec also says that writes to reserved and unimplemented
registers must be completed normally. It makes no statements about
writes to read-only registers, so be as conservative as possible,
while covering the exception to the rule that is documented in a
subpart of the standard.
Requested by: socttl
in all USB ethernet drivers. The qdat structure contains a pointer
to the interface's struct ifnet and is used to process incoming
packets, so simultaneous use of two similar devices caused crashes
and confusion.
The if_udav driver appeared in the tree since Daan's PR, so I made
similar changes to that driver too.
PR: kern/59290
Submitted by: Daan Vreeken <Danovitsch@Vitsch.net>
MFNetBSD 1.177; author: toshii
Use the correct wValue to get hub desriptors.
Also, make wValue checks of root hub codes less strict.
MFNetBSD 1.178: author: martin
Interrupt descriptors might become invalid while being processed in
uhci_check_intr - so remember their next pointer before calling it.
Patch provided by Matthew Orgass in PR kern/24542.
Obtained from: NetBSD
return value for BUS_READ_IVAR and thus don't generate the proper NULL
in cases where a device (i.e. on PCI) does not have a handle.
Found by: peadar, tjr
identifiers, to openfirmio.h as OFIOCMAXNAME, so programs can use it
for buffer sizes etc.
Note: Although this is only a rough upper limit to make the code more
robust and to prevent the allocation of ridiculous amounts of memory,
the current limit of one page (8191 + '\0' in openfirm_getstr()) still
appears a bit high. The maximum length of OFW property names is 31.
I didn't find a maximum length for the device identifiers in the OFW
documentation but it certainly is much smaller than 8191, too.
- Enable the OFIOCSET ioctl, i.e. move it out from under #if 0.
- Don't use openfirm_getstr() for the property value in OFIOCSET, there
are also properties whose values aren't strings and it makes sense to
use a different maximum length for property values than OFW_NAME_MAX/
OFIOCMAXNAME. The maximum accepted property value is defined in
openfirmio.h as OFIOCMAXVALUE (currently the maximum size of the value
of the nvramrc property).
- Make OFIOCSET not return EINVAL when OF_setprop() returns a different
length for the written value than it was told to write, this is normal
for the text string values of the properties in the OFW /options node.
Instead, only return EINVAL if OF_setprop() returned -1 (value could
not be written or property could not be created). Add a comment about
the specialty of the OFW /options node.
- Make OFIOCSET return the length of the written value returned by
OF_setprop(), just like OF_getprop() does. Quite useful, at least for
debugging.
Reviewed by: tmm
is being turned off, or else TCP/IP will keep assigning the job to us.
Drivers themselves should consult if_capenable, not if_hwassist--the
latter is for the TCP/IP stack.
Split the baby. For idepci devices, now both legacy mode bits need
not be set. We can run an idepci in a split mode. However, it only
works better than before, not works. It works better in that when one
device is legacy and the other isn't and disabled, we now operate
correctly.
sos submitted a version of this patch.
subclass, progif and revid. While these are typically read
only fields, they aren't always read-only. progif is writable
for ata devices, for example. It does no harm when they are
read only, and helps when they aren't.
to try to allocate things on my parent can be taken out. It duplicates code.
Also, add comment about why the power state stuff is here (type 2
devices don't participate in the power state save/restore due to
larger Bx issues).
chattiness was left in for debugging, but now that nearly all of the
problems relating to the changes have been fixed, it is only annoying. It
is still available via bootverbose.
Prodded by: jhb
because VLAN hardware features are enabled in em(4) by default.
Note: Currently vlan(4) has a bug that it consults
if_capabilities, not if_capenable. This will be fixed
after all the network drivers set VLAN bits in
if_capenable properly.
