previously know by StarSemi STR9104.
Tested by the submitter on an Emprex NSD-100 board.
Submitted by: Yohanes Nugroho <yohanes at gmail.com>
Reviewed by: freebsd-arm, stas
Obtained from: //depot/projects/str91xx/...
This brings hwpmc(4) support for 2nd and 3rd generation XScale cores.
Right now it's enabled by default to make sure we test this a bit.
When the time comes it can be disabled by default.
Tested on Gateworks boards.
A man page is coming.
Obtained from: //depot/user/rpaulo/xscalepmc/...
- Move USB serial drivers earlier to match their placement in other kernel
configs.
- Add descriptions to various USB drivers.
- Move the USB wireless drivers into a new section.
- Add ulscom to the list of USB serial drivers.
- The device is based on Marvell 88F6281 system on chip.
- More info about the platform at http://www.plugcomputer.org
- To build the FreeBSD kernel:
make buildkernel TARGET_ARCH=arm KERNCONF=SHEEVAPLUG
- Installation notes at: http://wiki.freebsd.org/FreeBSDMarvell
Submitted by: Michal Hajduk
Obtained from: Semihalf
respectivly. This will allow one to have a kernel with both devices
present and use it for multiple boards with different types of RTC
sitting on a bus.
Discussed with: imp
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
o add bus shim for cfi driver
o add static mapping for CS0 (we map all 16M as the cfi driver doesn't
support demand mapping)
Note this needs some tweaking to work for 2358 boards which is why the
CAMBRIA config is not touched.
options. Using the already included std.avila is not considered
to be entirely right (and the options slightly differ) but the best
match we currently have. Upcoming work should fit better.
Reorder another variable to match the layout of other configs.
Reviewed by: sam, warner (earlier version with options removed)
o add support for IXP435 cpu's (e.g. 64 irq's)
o add support for Cambria-specific devices: npe, led's (front panel and
octal latch), ehci, mcu, ide cf
o redo memory mapping for xscale/ixp4xx boards: previously memory
was assumed aliased to 0x10000000 but this appears to be true only
for ixp425 systems and breaks operation on others; rework so memory
is assumed to start at 0
o rework NPE configuration support to use NPE id's instead of port #'s;
these changes also rename the associated MAC's to follow the NPE's
they are attached to
o update npe firmware to latest rev (same license) and update default fw
imageid's to match; in particular this adds NPE-A and crypto support
o re-style NPE fw handling code and add a console msg identifying the
attributes of the loaded fw
o fix numerous problems with handling failures during npe setup
o fix npe rx q setup; need to spin waiting for mailbox responses during
early boot stages as qmgr interrupts are not delivered; this fixes
the problem where all 8 traffic classifications were not tied to the
rx q (and eliminates the console msg "remember to fix rx q setup")
o add DELAY to npe MII wait logic for IXP435
o strip down builtin phys->virt address translation table in resource
handling to just those resources that require it and add a console msg
to alert people when this (kludge) table needs to be extended
o purge a bunch of dead netbsd-ism's
o cleanup avila led driver
o add Cambria support to boot2 and rework code for better multi-board support
Notes:
1. NPE-A doesn't work and causes NPE-C to stop working; it is disabled
in the hints
2. USB isn't working yet; controller communicates ok but device
discovery fails
3. Cambria support must be configured separately from IXP425 boards;
multi-board support is TBD
Sponsored by: Hobnob, Gateworks (board donation)
Reviewed by: imp
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
