The real problem was that ioctl handlers needed to call amr_wait_command()
with the list lock held. This not only solves the completion race, it also
prevents bounce buffer corruption that could arise from amr_start() being
called without the proper locks held.
Discussed with: ps
MFC After: 3 days
the completion of the command can occur before tsleep is called and
the command ends up blocking forever since the wakeup has already
been called.
Submitted by: ups
routines.
- Add or replace cpu_spinwait() with DELAY(1) to a few of the busy
loops when reading from the controller to work around firmware bugs
which can crash the controller.
This is important with MegaLib, when issuing a GET_REBUILD_PROG since
it returns an error if the drive is not in rebuild state.
This will be MFC'ed shortly.
Submitted by: ps
Reviewed by: scottl
Found by: ambrisko
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.
Add in the Linux IOCTL shim and create the megadev0 device so
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.
Add glue to build the modules but don't tie it into the build
yet until I test it from the CVS repo. via the mirror on an
amd64 machine.
Tie this into the Linux32 emulation on amd64 so the tools can
run on amd64 kernel.
Cleaned up by: ps (amr_linux.c)
1. Implement a large set of ioctl shims so that the Linux management apps
from LSI will work. This includes infrastructure to support adding, deleting
and rescanning arrays at runtime. This is based on work from Doug Ambrosko,
heavily augmented by LSI and Yahoo.
2. Implement full 64-bit DMA support. Systems with more than 4GB of RAM
can now operate without the cost of bounce buffers. Cards that cannot do
64-bit DMA will automatically revert to using bounce buffers. This option
can be forced off by setting the 'hw.amr.force_sg32" tunable in the loader.
It should only be turned off for debugging purposes. This work was sponsored
by Yahoo.
3. Streamline the command delivery and interrupt handler paths after
much discussion with Dell and LSI. The logic now closely matches the
intended design, making it both more robust and much faster. Certain
i/o failures under heavy load should be fixed with this.
4. Optimize the locking. In the interrupt handler, the card can be checked
for completed commands without any locks held, due to the handler being
implicitely serialized and there being no need to look at any shared data.
Only grab the lock to return the command structure to the free pool. A
small optimization can still be made to collect all of the completions
together and then free them together under a single lock.
Items 3 and 4 significantly increase the performance of the driver. On an
LSI 320-2X card, transactions per second went from 13,000 to 31,000 in my
testing with these changes. However, these changes are still fairly
experimental and shouldn't be merged to 6.x until there is more testing.
Thanks to Doug Ambrosko, LSI, Dell, and Yahoo for contributing towards
this.
with no associated data. Also revert previous changes that allocate off
of the stack instead of using malloc, as it's not needed. Many thanks to
LSI for investigating and fixing these problems.
Submitted by: rajeshpr @ lsil . com
- Introduce the amr_io_lock to control access to command queues, bio queues,
and the hardware.
- Eliminate the taskqueue and do all completion processing in the ithread.
- Assign a static slot number to each command instead of doing a linear
search for free slots each time a command is needed.
- Modify the interrupt handler to more closely match what Linux does, for
safety.
properly support bounce buffers and resource shortages. This allows the
driver to work properly and reliably with more than 4GB of RAM. Of the
three data paths that exist in the driver, (block, CAM, ioctl), the ioctl
path has not been well tested with these changes due to difficulty with
finding an application that uses it that actually works.
Sponsored by: The FreeBSD Foundation and FreeBSD Systems, Inc.
Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.
Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT flags and adding 145 D_NEEDGIANT flags.
Previously the "struct disk" were owned by the device driver and this
gave us problems when the device disappared and the users of that device
were not immediately disappearing.
Now the struct disk is allocate with a new call, disk_alloc() and owned
by geom_disk and just abandonned by the device driver when disk_create()
is called.
Unfortunately, this results in a ton of "s/\./->/" changes to device
drivers.
Since I'm doing the sweep anyway, a couple of other API improvements
have been carried out at the same time:
The Giant awareness flag has been flipped from DISKFLAG_NOGIANT to
DISKFLAG_NEEDSGIANT
A version number have been added to disk_create() so that we can detect,
report and ignore binary drivers with old ABI in the future.
Manual page update to follow shortly.
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
Devices below may experience a change in geometry.
* Due to a bug, aic(4) never used extended geometry. Changes all drives
>1G to now use extended translation.
* sbp(4) drives exactly 1 GB in size now no longer use extended geometry.
* umass(4) drives exactly 1 GB in size now no longer use extended geometry.
For all other controllers in this commit, this should be a no-op.
Looked over by: scottl
Retain the mistake of not updating the devstat API for now.
Spell bioq_disksort() consistently with the remaining bioq_*().
#include <geom/geom_disk.h> where this is more appropriate.
in geom_disk.c.
As a side effect this makes a lot of #include <sys/devicestat.h>
lines not needed and some biofinish() calls can be reduced to
biodone() again.
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
turns runs its tasks free of Giant too. It is intended that as drivers
become locked down, they will move out of the old, Giant-bound taskqueue
and into this new one. The old taskqueue has been renamed to
taskqueue_swi_giant, and the new one keeps the name taskqueue_swi.
Change the argument to disk_destroy() to be the same struct disk * as
disk_create() takes.
This enables drivers to ignore the (now) bogus dev_t which disk_create()
returns.
as module. This also fix's issue kern/45713.
Fix - polling was implemented incorrectly for
adapter enquiry and adapter flush.
(2) Problem: PANIC when unloading driver
as module.
Fix - device nodes are not destroyed for amr0,
and amrd* when driver is unloaded
(3) Problem: PANIC from loading driver when
3ware adapter present, error message "Warning
"amrd is usurping twed's bmaj"
Fix - put #idef freebsd version < 500000 for
bmaj -1 -> amrd_cdevsw
(4) Problem: warnings in driver when compiling
with DAMR_DEBUG param enabled in Makefile
Fix - fix the warnings so driver can compile
when -Werror is present in Makefile.
Approved by: jhb
MFC: 7 days
amr_cam.c,
amrreg.h,
amrvar.h:
- added support for 12/16 byte cdb's, effecting CAM branch only ( non-disk support )
amrreg.h:
- increased number of scatter gather elements from 16 to 26.
amr_pci.c:
- amr_pci_free(), incorrect bus tag meant for 'amr_mailbox_dmat' was being freed
all:
- copyright change requested by scottl
Reviewed by: ps,scottl
MFC after: 1 week
changes for "LSILogic"
(2) enabled non-disk support through CAM interface
(3) HA_INQ (a) enabled tagged queuing (b) disable reset during
driver loading (b) renamed BSDi string to LSI
(4) disabled detecting disk devices during SCSI INQUIRY
(5) changed dcdb single element sglist to send one entire buffer chunk
(6) nsgelem not set in sglist
(7) ap_data_transfer_length not set for dcdb
(8) changed "struct thread" to "d_thread_t" for compatibliity { xxx_open,
xxx_close, xxx_ioctl }
(9) miscellaneous compatiblity fixes
(10) bug fix for 0x0409/0x1000 card
(11) added compiling amr_cam.c in sys/conf/files
(12) added compiling amr_cam.c in sys/modules/amr/Makefile
Reviewed by:ps
MFC after:1 week
1 week
and predictable way, and I apologize if I have gotten it wrong anywhere,
getting prior review on a patch like this is not feasible, considering
the number of people involved and hardware availability etc.)
If struct disklabel is the messenger: kill the messenger.
Inside struct disk we had a struct disklabel which disk drivers used to
communicate certain metrics to the disklayer above (GEOM or the disk
mini-layer). This commit changes this communication to use four
explicit fields instead.
Amongst the benefits is that the fields do not get overwritten by
wrong or bogus on-disk disklabels.
Once that is clear, <sys/disk.h> which is included in the drivers
no longer need to pull <sys/disklabel.h> and <sys/diskslice.h> in,
the few places that needs them, have gotten explicit #includes for
them.
The disklabel inside struct disk is now only for internal use in
the disk mini-layer, so instead of embedding it, we malloc it as
we need it.
This concludes (modulus any mistakes) the series of disklabel related
commits.
I belive it all amounts to a NOP for all the rest of you :-)
Sponsored by: DARPA & NAI Labs.
Rename diskerr() to disk_err() for naming consistency.
Drop the by now entirely useless struct disklabel argument.
Add a flag argument for new-line termination.
Fix a couple of printf-format-casts to %j instead of %l.
Correctly print the name of all bio commands.
Move the function from subr_disklabel.c to subr_disk.c,
and from <sys/disklabel.h> to <sys/disk.h>.
Use the new disk_err() throughout, #include <sys/disk.h> as needed.
Bump __FreeBSD_version for the sake of the aac disk drivers #ifdefs.
Remove unused disklabel members of softc for aac, amr and mlx, which seem
to originally have been intended for diskerr() use, but which only rotted
and got Copy&Pasted at least two times to many.
Sponsored by: DARPA & NAI Labs.
than %u for printing signed 64-bit types. It fails on different machines,
and has the wrong signdness.
Fixed old printf format error on the same line. %u is not suitable for
printing 32-bit types on all machines.
while it is on a queue with the queue lock and remove the per-task locks.
- Remove TASK_DESTROY now that it is no longer needed.
- Go back to inlining TASK_INIT now that it is short again.
Inspired by: dfr
queue, and a mutex to protect the global list of taskqueues. The only
visible change is that a TASK_DESTROY() macro has been added to mirror
the TASK_INIT() macro to destroy a task before it is free'd.
Submitted by: Andrew Reiter <awr@watson.org>
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
decode the BIOS and firmware version and announce the board as HP NetRaid.
This has been tested with a NetRaid 3si controller, the BIOS/firmware
printout should also work for other NetRaid controllers but the type
detection for other NetRaids (such as the 1si) will not work due to the
lack of hardware.
Reviewed by: msmith
Fix amr_map_command so that 40LD-specific commands get the scatter-gather
list count in the right place. I don't understand why AMI did it like
this, but now the AMI MegaManager can talk to the newer (1600 and later)
controllers.
Remove an unused variable.
Include <machine/clock.h> when necessary.
Tweak some debugging levels to make things more intelligible.
- New support for 40LD firmware found in Series 475 and 471 adapters.
- Better support for 8LD firmware adapters
- Ioctl passthrough interface for userland utilities.
- Improved error handling and queueing.
- Several bugfixes (including the 'still open' shutdown bug and
closing some small race conditions).
- Zone-style command allocator, reducing memory wasted under heavy
load conditions.
- CAM interface (disabled and not fully working) for SCSI passthrough
access to non-disk devices
Thanks to AMI for supplying a pile of new adapters and various other
help in making this happen.
map physical addresses below 0x2000 (accoding to AMI). If we
allocate our s/g tables and get an address below this point, leak the
memory and try again.
This should fix booting from these controllers.