consistent with the naming of other structure field members, and
reducing improper grep matches. Clean up and comment structure
fields in structure definition.
sc->mii_anegticks according to whether the respective BGE chip
supports Fast Ethernet only or also Gigabit Ethernet.
- At least the BGE chips I've tested with wedge when isolating them
so document this as the reason for setting MIIF_NOISOLATE and
remove the unused (and partially even #ifdef'ed out) isolation
related code. Add code that panics if we encounter a non-zero MII
instance as generally there's no way a PHY requiring MIIF_NOISOLATE
can be handled gracefully in a multi-PHY configuration (it's ok for
the internal PHY of single-PHY-only-NIC to not support isolation
though).
- Additionally set MIIF_NOLOOP as loopback doesn't seem to work
either and remove the #ifdef'ed out code for adding respective
media. The MIIF_NOLOOP flag currently triggers nothing but
hopefully will be respected by mii_phy_setmedia() later on.
Reviewed by: jkim, yongari
MFC after: 1 month
Blade 2500, Fire V210 and probably some other sparc64 machines.
These chips are typically not fitted with an EEPROM which means
that we have to obtain the MAC address via OFW and that some chip
tests will just always fail.
These changes are based on the respective code found in OpenBSD
with some additional info obtained from OpenSolaris and some style
suggestions by jkim@. They also have the desired side-effect of
respecting the 'local-mac-address?' system configuration variable
for the affected BGEs.
- In bge_attach() factor out calling bge_release_resources() before
going to the fail label into the fail label as well as replace a
magic 6 with ETHER_ADDR_LEN.
Reviewed by: yongari (before style changes), jkim
- Wake up DMA engine after adding a new receive buffer.
- Skip buffers which have unknown state after error.
- More rigid error detection.
MFC after: 1 week
as some combinations of chipset, controller and target do not behave
correctly when DMA is enabled for other commands.
PR: kern/103602
MFC after: 2 weeks
were never freed, but the big ring was freed twice.
-Don't supply rx hw csums for frames which are padded beyond the
length specified in the ip header. If the padding is non-zero,
the hw csum will be incorrect for such frames.
Sponsored by: Myricom
non-mapped data as possible at once and not page-by-page. Which this change we
combain I/Os, but also saves many VM_OBJECT_UNLOCK()/VM_OBJECT_LOCK()
operations.
Simple 'fsx -l 33554432 -o 524288 -N 10000 /tank/fsx' test shows ~23%
performance increase.
This workaround the problem in Parallels/VMWare where the emulated drivers are
slower, especially with ATA_FLUSHCACHE. The problem appears much more
frequently with ZFS which use it a lot more.
Approved: sos, pjd
- vm_page_undirty() is enough (instead of vm_page_set_validclean()), but it has
to be called before we write the data in case someone makes page dirty after
our write, but before our vm_page_undirty() call.
- Always dmu_write, not matter if uiomove() succeeded, because it could
partially be ok and we would lose some changes.
All good ideas from: ups
In dounmount(), before or while vn_lock(coveredvp) is called, coveredvp
vnode may be VI_DOOMED due to one of the following:
- other thread finished unmount and vput()ed it, and vnode was chosen
for recycling, while vn_lock() slept;
- forced unmount of the coveredvp->v_mount fs.
In the first case, next check for changed v_mountedhere or mnt_gen counter
would be successfull. In the second case, the unmount shall be allowed.
Submitted by: sobomax
MFC after: 2 weeks
- Fix for a bug where a close would not wait for all (directio)
dirty buffers to drain. The nfsnode was not marked NMODIFIED
when there were directio dirtied buffers pending, causing this.
- No reason to vhold/vrele the vp when enqueueing DirectIO requests
for the nfsiods. The vnode can't really go way since the close
has to wait for these requests to drain.
MFC after: 1 week
Submitted by: mohans
specific request and thus should first try to be allocated from the
sys_resource pool. This avoids using the sys_resource pool for wildcard
requests that have bounded ranges coming from cbb(4) and Host-PCI pcib(4)
drivers.
Tested by: Andrea Bittau <a.bittau of cs.ucl.ac.uk fame>
Sleuthing by: Andrea Bittau as well
that the MSI mapping window is fixed at 0xfee00000 and the capability
does not include two more dwords used to program the address. Supporting
this mostly results in quieting spurious warnings during boot about
non-default MSI mapping windows.
- HT 2.00b also added a new HT capability type, so support that in pciconf.
MFC after: 3 days
Tested by: jmg
It seems that valid pause frames(Tx flow control) cause GMAC to hang
such that it resulted in watchdog timeout. As a work around don't
flush Rx MAC FIFO if we've received pause frames.
Tested by: Harald Schmalzbauer (h DOT schmalzbauer AT omnisec DOT de)
Under certain circumtances, if TSO is active, Yukon II generates
corrupted IP packets. All corrupted IP packets I noticed were the the
last segmented packet in a TSO request. The corrupted packet resulted
in retransmission of the damaged packet which in turn decreased network
performance dramatically.
Unfortunately it seems that there is no way to workaround this bug
as TSO is completely handled in hardware. Disable TSO until we find a
working workaround or a new silicon revision that doesn't have this
hardware bug.
fault. The previous method zero'd out the page tables, invalidated the
TLB, and then entered a spin loop. The idea was that the instruction after
the TLB invalidate would result in a page fault and the page fault and
subsequent double fault wouldn't be able to determine the physical page
for their fault handlers' first instruction. This stopped working when
PGE (PG_G PTE/PDE bit) support was added as a TLB invalidate via %cr3
reload doesn't clear TLB entries with PG_G set. Thus, the CPU was still
able to map the virtual address for the spin loop and happily performed
its infinite loop.
The triple fault now uses a much more deterministic sledge-hammer approach
to generate a triple fault. First, the IDT descriptor is set to point to
an empty IDT, so any interrupts (including a double fault) will instantly
fault. Second, we trigger a int 3 breakpoint to force an interrupt and
kick off a triple fault.
MFC after: 3 days
in all other file system on FreeBSD (instead from inactive() method).
A nice side-effect of this change, except that it speedups file system
when mmaped file are often open/closed, is that it makes FreeBSD's
namecache work:)
This fixes slow operations on mmaped files, because without this fix,
pages were written to disk multiple times.
If one is looking for even greater speed up for such operation, he should
disable ZIL (by setting vfs.zfs.zil_disable to 1 in /boot/loader.conf).
Disabling ZIL makes fsx run ~9 times faster.
supports software encrypt/decrypt.
The nuked code itself is quite problematic, as pointed out by sam@ ---
wk->wk_keyix should be replaced by the loop count.
Tested with WEP/TKIP/CCMP/no-protection.
Approved by: sam@ (mentor)
Noticed by: Hans Petter Selasky <hselasky@c2i.net>
o Fix linewrap issues.
o Fix two typos (s/Recomended/Recommended/ and s/tunning/tuning/)
o Remove a couple of extra instances of the word "of".
o Update names of kmem_size variables.
Approved by: pjd
where similar data structures exist to support devfs and the MAC
Framework, but are named differently.
Obtained from: TrustedBSD Project
Sponsored by: SPARTA, Inc.
by Philippe Biondi and Arnaud Ebalard. This is a temporary fix
until more discussion can be had on the exact risks involved in
allowing source routing in IPv6
Submitted by: itojun
Reviewed by: jinmei
MFC after: 1 day
- Move FreeBSD-specific code to zfs_freebsd_*() functions in zfs_vnops.c
and keep original functions as similar to vendor's code as possible.
- Add various includes back, now that we have them.
macro, as za_first_integer field also contains type. This should be fixed in
ZFS itself, but this bug is not visible on Solaris, because there, type is
not stored in za_first_integer. On the other hand it will be visible on
MacOS X.
Reported by: Barry Pederson <bp@barryp.org>
variable name conventions for arguments passed into the framework --
for example, name network interfaces 'ifp', sockets 'so', mounts 'mp',
mbufs 'm', processes 'p', etc, wherever possible. Previously there
was significant variation in this regard.
Normalize copyright lists to ranges where sensible.
labels: the mount label (label of the mountpoint) and the fs label (label
of the file system). In practice, policies appear to only ever use one,
and the distinction is not helpful.
Combine mnt_mntlabel and mnt_fslabel into a single mnt_label, and
eliminate extra machinery required to maintain the additional label.
Update policies to reflect removal of extra entry points and label.
Obtained from: TrustedBSD Project
Sponsored by: SPARTA, Inc.
the introduction of priv(9) and MAC Framework entry points for privilege
checking/granting. These entry points exactly aligned with privileges and
provided no additional security context:
- mac_check_sysarch_ioperm()
- mac_check_kld_unload()
- mac_check_settime()
- mac_check_system_nfsd()
Add mpo_priv_check() implementations to Biba and LOMAC policies, which,
for each privilege, determine if they can be granted to processes
considered unprivileged by those two policies. These mostly, but not
entirely, align with the set of privileges granted in jails.
Obtained from: TrustedBSD Project
- Redistribute counter declarations to where they are used, rather than at
the file header, so it's more clear where we do (and don't) have
counters.
- Add many more counters, one per policy entry point, so that many
individual access controls and object life cycle events are tracked.
- Perform counter increments for label destruction explicitly in entry
point functions rather than in LABEL_DESTROY().
- Use LABEL_INIT() instead of SLOT_SET() directly in label init functions
to be symmetric with destruction.
- Align counter names more carefully with entry point names.
- More constant and variable name normalization.
Obtained from: TrustedBSD Project
- Add a more detailed comment describing the mac_test policy.
- Add COUNTER_DECL() and COUNTER_INC() macros to declare and manage
various test counters, reducing the verbosity of the test policy
quite a bit.
- Add LABEL_CHECK() macro to abbreviate normal validation of labels.
Unlike the previous check macros, this checks for a NULL label and
doesn't test NULL labels. This means that optionally passed labels
will now be handled automatically, although in the case of optional
credentials, NULL-checks are still required.
- Add LABEL_DESTROY() macro to abbreviate the handling of label
validation and tear-down.
- Add LABEL_NOTFREE() macro to abbreviate check for non-free labels.
- Normalize the names of counters, magic values.
- Remove unused policy "enabled" flag.
Obtained from: TrustedBSD Project
set/clear it but would not do it. Now we will.
- Moved to latest socket api for extended sndrcv info struct.
- Moved to support all new levels of fragment interleave.
calls. Add MAC Framework entry points and MAC policy entry points for
audit(), auditctl(), auditon(), setaudit(), aud setauid().
MAC Framework entry points are only added for audit system calls where
additional argument context may be useful for policy decision-making; other
audit system calls without arguments may be controlled via the priv(9)
entry points.
Update various policy modules to implement audit-related checks, and in
some cases, other missing system-related checks.
Obtained from: TrustedBSD Project
Sponsored by: SPARTA, Inc.
- Replace PRIV_NFSD with PRIV_NFS_DAEMON, add PRIV_NFS_LOCKD.
- Use PRIV_NFS_DAEMON in the NFS server.
- In the NFS client, move the privilege check from nfslockdans(), which
occurs every time a write is performed on /dev/nfslock, and instead do it
in nfslock_open() just once. This allows us to avoid checking the saved
uid for root, and just use the effective on open. Use PRIV_NFS_LOCKD.
@118370 Correct typo.
@118371 Integrate changes from vendor.
@118491 Show backtrace on unexpected code paths.
@118494 Integrate changes from vendor.
@118504 Fix sendfile(2). I had two ways of fixing it:
1. Fixing sendfile(2) itself to use VOP_GETPAGES() instead of
hacking around with vn_rdwr(UIO_NOCOPY), which was suggested
by ups.
2. Modify ZFS behaviour to handle this special case.
Although 1 is more correct, I've choosen 2, because hack from 1
have a side-effect of beeing faster - it reads ahead MAXBSIZE
bytes instead of reading page by page. This is not easy to implement
with VOP_GETPAGES(), at least not for me in this very moment.
Reported by: Andrey V. Elsukov <bu7cher@yandex.ru>
@118525 Reorganize the code to reduce diff.
@118526 This code path is expected. It is simply when file is opened with
O_FSYNC flag.
Reported by: kris
Reported by: Michal Suszko <dry@dry.pl>
vm.kmem_size_min. Useful when using ZFS to make sure that vm.kmem size will
be at least 256mb (for example) without forcing a particular value via vm.kmem_size.
Approved by: njl (mentor)
Reviewed by: alc
from the incoming SYN handling section of tcp_input().
Enforcement of the accept queue limits is done by sonewconn() after the
3WHS is completed. It is not necessary to have an earlier check before a
connection request enters the SYN cache awaiting the full handshake. It
rather limits the effectiveness of the syncache by preventing legit and
illegit connections from entering it and having them shaken out before we
hit the real limit which may have vanished by then.
Change return value of syncache_add() to void. No status communication
is required.
when the ACK is invalid and doesn't belong to any registered connection,
either in syncache or through SYN cookies. True but a NULL struct socket
is returned when the 3WHS completed but the socket could not be created
due to insufficient resources or limits reached.
For both cases an RST is sent back in tcp_input().
A logic error leading to a panic is fixed where syncache_expand() would
free the mbuf on socket allocation failure but tcp_input() later supplies
it to tcp_dropwithreset() to issue a RST to the peer.
Reported by: kris (the panic)
when one of links is inactive and have stale sequence number. To avoid
this sequence numbers of all links are getting updated on every
successful packet reassembling.
- ng_ppp_bump_mseq function created to simplify code.
- ng_ppp_frag_drop function separated from ng_ppp_frag_process to
simplify code.
Reviewed by: archie
Approved by: glebius (mentor)
which lead to ineffective multilink packet distribution plans.
- Changed bytesInQueue calculation math to have more precise information
about links utilization.
- Taken rough account of the link overhead. Better way to do it could be to
get exact overhead from user-level, but I have not done it to keep
binary compatibility.
Reviewed by: archie
Approved by: glebius (mentor)
be applied to dev entries. This leaves us with file times like "Jan 1 1970."
Work around this problem by replacing the tv_sec == 0 check with a
<= 3600 check. It's doubtful anyone will be booting within an hour of the
Epoch, let alone care about a few seconds worth of nonzero timestamps. It's
a hackish work around, but it does work and I have not experienced any
negatives in my testing.
Discussed with: bde
"Ok with me: phk
and new SCBs were allocated on demand later if needed. This has two
problems. First, allocating SCBs involves allocating contiguous memory,
and if memory is exhausted then the VM will try to page out to satisfy
the request, leading to recursion and deadlock. The second problem is
that it can cause lock order reversals due to parts of the VM still being
under Giant.
Fix the problem be allocating the full pool at driver attach, when it is
safe to do so.
1. CMSG_NXTHDR(mhdr, cmsg) is supposed to dereference cmsg and return
the next header in the chain. If cmsg is NULL it should return
the first header, behaving essentially like CMSG_FIRSTHDR().
2. inet6_rth_(space|init|add) should do basic checking on their input
to verify that the number of headers (segments) is
between 0 and 127 inclusive.
MFC-After: 1 month
and should only be applied on certain specific card / vendor, hence the
addition of ac97_getsubvendor().
- Fix low volume issue on several MSI laptops through ALC655 quirk.
Reported/Tested by: Christian Mueller
<raptor-freebsd-multimedia@xpls.de>
MFC after: 1 week
- For ural(4):
o Fix node leakage in ural_start(), if ural_tx_mgt() fails.
o Fix mbuf leakage in ural_tx_{mgt,data}(), if usbd_transfer() fails.
o In ural_tx_{mgt,data}(), set ural_tx_data.{m,ni} to NULL, if
usbd_transfer() fails, so they will not be freed again in ural_stop().
Approved by: sam (mentor)
- Removed free-oqueue cache.
- Fix counter for sq entries
- Increased the amount of information retained
on ASOC_TSN logging on the association.
- Made it so with the ASOC_TSN logging on
sending or recieving an abort we dump the log.
- Went through and added invariant's around some
panic's that needed them.
- decrements went to atomic_subtact_int instead of add -1
- Removed residual count increment that threw off a
strm oq count.
- Tracks and complaints if we don't have a LAST fragment and
clean up the sp structure.
- Track a new stat that counts number of abandoned msgs that
happen if you close without reading.
- Fix lookup of frag point to be aware of a 0 assoc-id.
Reviewed by: gnn
Group mutexes used in hwpmc(4) into 3 "types" in the sense of
witness(4):
- leaf spin mutexes---only one of these should be held at a time,
so these mutexes are specified as belonging to a single witness
type "pmc-leaf".
- `struct pmc_owner' descriptors are protected by a spin mutex of
witness type "pmc-owner-proc". Since we call wakeup_one() while
holding these mutexes, the witness type of these mutexes needs
to dominate that of "sleepq chain" mutexes.
- logger threads use a sleep mutex, of type "pmc-sleep".
Submitted by: wkoszek (earlier patch)
When nbytes=0, sendfile(2) should use file size. Because of the bug, it
was sending half of a file. The bug is that 'off' variable can't be used
for size calculation, because it changes inside the loop, so we should
use uap->offset instead.
contigmalloc2() was always testing the first physical page for PG_ZERO,
not the current page of interest.
Submitted by: Michael Plass
PR: 81301
MFC after: 1 week
gets a bogus irq storm detected when periodic daily kicks off at 3 am
and disconnects the disk. Change the print logic to print once per second
when the storm is occurring instead of only once. Otherwise, it appeared
that something else was causing the errors each night at 3 am since the
print only occurred the first time.
Reviewed by: jhb
MFC after: 1 week
on a snapshot directory:
- Remove PRIV_VFS_MOUNT check - regular users can mount snapshots
via lookups on snapshot directory.
- Reset mount credential to kcred, so user won't be able to unmount
the snapshot.
- Reset owner uid.
- Unlock vnode in case of a failure.
Reported by: simokawa
Previously whenever PROMISC mode turned on/off link renegotiation
occurs and it could resulted in network unavailability for serveral
seconds.(Depending on switch STP settings it could last several tens
seconds.)
Reported by: Prokofiev S.P. < proks AT logos DOT uptel DOT net >
Tested by: Prokofiev S.P. < proks AT logos DOT uptel DOT net >
This fixes stange panics when listing .zfs/snapshot/ directory for me.
Reported by: simokawa
Reported by: Johan Hendriks <Johan@double-l.nl>
- Hide cache_purge() under FREEBSD_NAMECACHE like in other files.
- Protect mnt_flag with mount interlock.
to free the oldest entry in the current bucket row. The global
entry limit may be smaller than the bucket rows and their limit
combined however. Thus only try to free a syncache entry if we
found one in this bucket row.
Reported by: kris
to move up the start address until the allocation succeeds. If the
alignment of the resource was 0, then the code would keep trying the same
request in an infinite loop and hang. Force the request to always move
start up by at least 1 byte each time through the loop.
The 6105M and 6102 does not have the DWORD alignment problem, so
don't m_defrag() every packet in the transmit path for those.
More stringent usage of tx-descriptor ring and its flags.
Tested on 6102 and 6105M, other chips may also be able to run
without the m_defrag() but I have neither hardware nor docs to
find out.
Sponsored by: Soekris Engineering
"zone", which is generally not present in zone names. This reduces the
incidence of line-wrapping in "vmstat -z " using 80-column displays.
MFC after: 3 days
The name trunk is misused as the networking term trunk means carrying multiple
VLANs over a single connection. The IEEE standard for link aggregation (802.3
section 3) does not talk about 'trunk' at all while it is used throughout IEEE
802.1Q in describing vlans.
The lagg(4) driver provides link aggregation, failover and fault tolerance.
Discussed on: current@
unload instead of returning EBUSY. This check tells if there are mounted
ZFS file systems or not. We can't unload if there are mounted file systems.
Reported by: Andrey V. Elsukov <bu7cher@yandex.ru>
requests where uio_offset is not 0 to begin with. This fixes a long-
standing bug where e.g. 'cat /proc/$$/regs' would loop forever.
MFC after: 3 weeks
- Fix bug that prevented EEOR mode from working
and simplified the can_we_split code in the process.
- Reduce lock contention for the tcb_send_lock. I did
this especially for EEOR mode, still need to look at
why I need a lock when removing from the tailq and the
->next is NOT null. A lock fixes it but it implies a
bug yet exists.
- Activated Andre's proposed changes to better use the mbuf
infrastructure.
- Fixed places that were not using the aloc macro's to take
advantage of the per assoc cache.
- Adds ifdef fix so any logging will enable stat_logging to
get the right data structures in place (suggested by Max Laier).
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant and operate as
usual. RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.
The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.
implement robust version of m_collapse
add support for sf_buf
add fix for m_iovappend
add calls to m_sanity under INVARIANTS
fix m_freem_vec to correctly travese the mbuf iovec chain
The pfs_info mutex is only needed to lock pi_unrhdr. Everything else
in struct pfs_info is modified only while Giant is held (during
vfs_init() / vfs_uninit()); add assertions to that effect.
Simplify pfs_destroy somewhat.
Remove superfluous arguments from pfs_fileno_{alloc,free}(), and the
assertions which were added in the previous commit to ensure they were
consistent.
Assert that Giant is held while the vnode cache is initialized and
destroyed. Also assert that the cache is empty when it is destroyed.
Rename the vnode cache mutex for consistency.
Fix a long-standing bug in pfs_getattr(): it would uncritically return
the node's pn_fileno as st_ino. This would result in st_ino being 0
if the node had not previously been visited by readdir(), and also in
an incorrect st_ino for process directories and any files contained
therein. Correct this by abstracting the fileno manipulations
previously done in pfs_readdir() into a new function, pfs_fileno(),
which is used by both pfs_getattr() and pfs_readdir().
- Reduce default number of spa_zio_* threads to N*spa_zio_issue
plus N*spa_zio_intr threads per ZIO type, where N is the number
of CPUs.
- Put ZIO type number in thread's name.
sendmsg() while using a 0-length msg_controllen. This isn't allowed in
the FreeBSD system call ABI, so detect this case and set msg_control to
NULL. This allows Linux ping to work.
Submitted by: rdivacky
- name change of prefered -> preferred
- CMT fast recover code added.
- Comment fixes in CMT.
- We were not giving a reason of cant_start_asoc per socket api
if we failed to get init/or/cookie to bring up an assoc. Change
so we don't just give a generic "comm lost" but look at actual
states of dying assoc.
- change "crc32" arguments to "crc32c" to silence strict/noisy
compiler warnings when crc32() is also declared
- A few minor tweaks to get the portable stuff truely portable
for sctp6_usrreq.c :-D
- one-2-one style vrf match problem.
- window recovery would leave chks marked for retran
during window probes on the sent queue. This would then
cause an out-of-order problem and assure that the flight
size "problem" would occur.
- Solves a flight size logging issue that caused rwnd
overruns, flight size off as well as false retransmissions.g
- Macroize the up and down of flight size.
- Fix a ECNE bug in its counting.
- The strict_sacks options was causing aborts when window probing
was active, fix to make strict sacks a bit smarter about what
the next unsent TSN is.
- Fixes a one-2-one wakeup bug found by Martin Kulas.
- If-defed out form, Andre's copy routines pending his
commit of at least m_last().. need to adjust for 6.2 as
well.. since m_last won't exist.
Reviewed by: gnn
which has already been freed by in_ifdetach(). With this cumulative change,
the removal of a member interface will not cause a panic in pfsync(4).
Requested by: yar
PR: 86848
- We need to allow for PRIV_VFS_MOUNT_OWNER inside a jail.
- Move security checks to vfs_suser() and deny unmounting and updating
for jailed root from different jails, etc.
OK'ed by: rwatson
than 2GB of RAM. This was because our physmem is long and 'physmem*PAGESIZE'
can be negative for more than 2GB of memory.
Reported by: Andrey V. Elsukov <bu7cher@yandex.ru>
It is not yet tested by Andrey, so there can be other problems, but this
was definiately a bug, so I'm committing a fix now.
tokens. Currently, we do not support the set{get}audit_addr(2) system
calls which allows processes like sshd to set extended or ip6
information for subject tokens.
The approach that was taken was to change the process audit state
slightly to use an extended terminal ID in the kernel. This allows
us to store both IPv4 IPv6 addresses. In the case that an IPv4 address
is in use, we convert the terminal ID from an struct auditinfo_addr to
a struct auditinfo.
If getaudit(2) is called when the subject is bound to an ip6 address,
we return E2BIG.
- Change the internal audit record to store an extended terminal ID
- Introduce ARG_TERMID_ADDR
- Change the kaudit <-> BSM conversion process so that we are using
the appropriate subject token. If the address associated with the
subject is IPv4, we use the standard subject32 token. If the subject
has an IPv6 address associated with them, we use an extended subject32
token.
- Fix a couple of endian issues where we do a couple of byte swaps when
we shouldn't be. IP addresses are already in the correct byte order,
so reading the ip6 address 4 bytes at a time and swapping them results
in in-correct address data. It should be noted that the same issue was
found in the openbsm library and it has been changed there too on the
vendor branch
- Change A_GETPINFO to use the appropriate structures
- Implement A_GETPINFO_ADDR which basically does what A_GETPINFO does,
but can also handle ip6 addresses
- Adjust get{set}audit(2) syscalls to convert the data
auditinfo <-> auditinfo_addr
- Fully implement set{get}audit_addr(2)
NOTE: This adds the ability for processes to correctly set extended subject
information. The appropriate userspace utilities still need to be updated.
MFC after: 1 month
Reviewed by: rwatson
Obtained from: TrustedBSD
- Tune number of namecache entires better (based on desiredvnodes).
- Handle vfs_lowvnodes event by releasing requested number of name cache
entries, but no less than 5%.
Reported by: simokawa
specific nodes when the process exits)
Move the vnode-cache-walking loop which was duplicated in pfs_exit() and
pfs_disable() into its own function, pfs_purge(), which looks for vnodes
marked as dead and / or belonging to the specified pfs_node and reclaims
them. Note that this loop is still extremely inefficient.
Add a comment in pfs_vncache_alloc() explaining why we have to purge the
vnode from the vnode cache before returning, in case anyone should be
tempted to remove the call to cache_purge().
Move the special handling for pfstype_root nodes into pfs_fileno_alloc()
and pfs_fileno_free() (the root node's fileno must always be 2). This
also fixes a bug where pfs_fileno_free() would reclaim the root node's
fileno, triggering a panic in the unr code, as that fileno was never
allocated from unr to begin with.
When destroying a pfs_node, release its fileno and purge it from the
vnode cache. I wish we could put off the call to pfs_purge() until
after the entire tree had been destroyed, but then we'd have vnodes
referencing freed pfs nodes. This probably doesn't matter while we're
still under Giant, but might become an issue later.
When destroying a pseudofs instance, destroy the tree before tearing
down the fileno allocator.
In pfs_mount(), acquire the mountpoint interlock when required.
MFC after: 3 weeks
a single conditional. The two operations are linked, but since the link
is not very direct, Coverity can't see it. Humans might also miss the
link as well. So, this isn't fixing any actual bugs, just improving
readability.
CID: 1787 (likely others as well)
Found by: Coverity Prevent (tm)
directly to a merged model where only one callout, the next to fire,
is registered.
Instead of callout_reset(9) and callout_stop(9) the new function
tcp_timer_activate() is used which then internally manages the callout.
The single new callout is a mutex callout on inpcb simplifying the
locking a bit.
tcp_timer() is the called function which handles all race conditions
in one place and then dispatches the individual timer functions.
Reviewed by: rwatson (earlier version)
Yukon II generated corrupted TCP checksum for short TCP packets
that's less than 60 bytes in size(e.g. window probe packet, pure ACK
packet etc). Padding the frame with zeros to make the frame minimum
ethernet frame size didn't work at all. Instead of dropping Tx
checksum offload support we calculate TCP checksum with S/W method
when we encounter short TCP frames.
Fortunately it seems that short UDP datagrams appear to be handled
correctly by Yukon II.
While I'm here simplify ethernet/VLAN header size calculation logic.
PR: 111384
popular names. Hence:
- comment current index() and rindex() functions, as these serve the same
functionality as, respectively, strchr() and strrchr() from userland;
- add inlined version of strchr() and strrchr(), as we tend to use them more
often;
- remove str[r]chr() definitions from ZFS code;
Reviewed by: pjd
Approved by: cognet (mentor)
front-end if the dpt(4) module is built along with a kernel that
includes eisa(4) or when compiling it stand-alone (logic based on
the corresponding ISA logic in sys/modules/sound/sound/Makefile).
As as side-effect this fixes the stand-alone build of the dpt(4)
module after dpt.h 1.17, dpt_eisa.c 1.22 and dpt_scsi.c 1.55.
Breakage reported by: n_hibma
does not prevent handle_workitem_remove() from recursing into a blocking
version. Add the dirrem to worklist instead of processing it now if this
is the case.
Reported and tested by: kris
Submitted by: tegge
MFC after: 2 weeks
- Allow to shrink ARC down to 16MB (instead of 64MB).
- Set arc_max to 1/2 of kmem_map by default.
- Start freeing things earlier when low memory situation is detected.
- Serialize execution of arc_lowmem().
I decided to setup minimum ZFS memory requirements to 512MB of RAM and 256MB of
kmem_map size. If there is less RAM or kmem_map, a warning will be printed.
World is cruel, be no better. In other words: modern file system requires
modern hardware:)
From ZFS administration guide:
"Currently the minimum amount of memory recommended to install a Solaris
system is 512 Mbytes. However, for good ZFS performance, at least one
Gbyte or more of memory is recommended."
tolerance. This driver allows aggregation of multiple network interfaces as
one virtual interface using a number of different protocols/algorithms.
failover - Sends traffic through the secondary port if the master becomes
inactive.
fec - Supports Cisco Fast EtherChannel.
lacp - Supports the IEEE 802.3ad Link Aggregation Control Protocol
(LACP) and the Marker Protocol.
loadbalance - Static loadbalancing using an outgoing hash.
roundrobin - Distributes outgoing traffic using a round-robin scheduler
through all active ports.
This code was obtained from OpenBSD and this also includes 802.3ad LACP support
from agr(4) in NetBSD.
the args for hash32_stre and hash32_strne but there are no consumers in the
base system and openbgpd does not use it which the initial import was for.
Silence on: hackers
