explicitly test and panic. This should not ever happen, but if it does,
this is a preferred failure mode to a NULL pointer dereference in kernel.
Coverity CID: 1716
Found with: Coverity Prevent(tm)
incorrect, non-bundlable fragmentation.
- Added min residual to better control split points for
both how big a msg must be as well as how much needs
to be left over.
- With our new algo in place, we need to implicitly
set "end of msg" on the sp-> structure otherwise we
end up with "hung" associations.
- Room reserved up front in IP header by pushing IP
header to back of mbuf.
- Fix so FR's peg count of retransmissions needed.
- Fix so an unlucky chunk that never gets across
will kill the assoc via the kill timer and send an
abort too.
- Fix bug in sctp_input which can result in a crash.
- Do not strip off IP options anymore.
- Clean up sctp_calculate_rto().
- Get rid of unused sysctl.
- Fixed so we discard all M-Cast
- Fixed so port check done AFTER checksum
- Fixed bug in fragmentation code that prevented
us from fragmenting a small complete message when
we needed to.
- Window probes were not marked back to unsent and
flight adjusted when a sack came in with no
window change or accepting of the probe data.
We now fix this with having a mark on the net and
the chunk so we can clear it out when the sack arrives
forcing it to retran just like it was "new" this
improves the handling of window probes, which were
dropped by the receiver.
- Tighten AUTH protocol error checks during INIT/INIT-ACK exchange
We can now use LOCK_CLASS() as a stronger check in lockmgr_chain() as a
result. This required putting back lk_flags as lockmgr's use of flags
conflicted with other flags in lo_flags otherwise.
- Tweak 'show lock' output for lockmgr to match sx, rw, and mtx.
seminfo because kernel_sysctlbyname() is slow. There is no dependency
problem since linux module depends on both sysvmsg and sysvsem and linprocfs
depends on it in turn.
Pointed out by: des
Reviewed by: des
Dont "return" in linux_clone() after we forked the new process in a case
of problems. Move the copyout of p2->p_pid outside the emul_lock coverage.
Submitted by: Roman Divacky
for doing this job. This change will make it easy to migrate from using
spinning locks to adaptive ones.
Reviewed by: glebius, julian
Approved by: cognet (mentor)
* Join the IPv4 all-hosts multicast group 224.0.0.1 once only;
that is, when an IPv4 address is first configured on an interface.
* Do not join it for subsequent IPv4 addresses as this violates IGMP.
* Be sure to leave the group when all IPv4 addresses have been removed
from the interface.
* Add two DIAGNOSTIC printfs related to the issue.
Further care and attention is needed in this area; it is suggested that
netinet's attachment to the ifnet structure be compartmentalized and
non-implicit.
Bug found by: andre
MFC after: 1 month
defined with VFS_LOCK_GIANT(NULL) call.
This shall fix softdep operation when mpsafe_vfs = 0.
Reported and tested by: kris
Submitted by: tegge
MFC after: 1 week
GetSeconds(). Instead, use CRTR register shifted right 15. This
gives us a range of 32 seconds we can do for timeout.
Shift to using == rather than < or > for calculating the timeout,
since if we can't read the ST_CTRT register twice in a second we have
even bigger problems to worry about, and == deals with the 'wrap'
issue.
This lets me type at the boot2 prompt again! Woo Hoo!
Bogusness noticed by: tisco
Pointy Hat to: That silly imp guy
CSD is usually 512 (well, 9), but for 2GB (and the rogue 4GB SD cards)
it is 1024 (or 2048 for 4GB). This value doesn't work for the block
read commands (which really want 512). Hardcode 512 for those. This
may break really old MMC cards that don't have a 512 block size (I've
never seen one: make my day and send me one :-), but since the MMC
side of the house is currently broken, it should only have the effect
that 2GB (and non-conforming 4GB) SD cards will work.
My 'non-conforming' 4GB SD card also works now too. The
non-conforming 4GB SD cards were sold for a while before the SD
association was worried they would be (a) incompatible (different FAT
flavor on them) and (b) confusing for the new SDHC standard and
cracked down on suppliers' bogus use of the SD trademark...
The changes to getstr() is so that the character that is
passed in to it, is also processed just as the rest. I also
removed one of the getc() calls otherwise you loose every
second character.
I also changed the strcpy of kname, so that it only happens if
kname is '\0'. This is so that one can pass a kernel in
through /boot.config.
The last change to boot2.c is in parse(). If you tried to type
a kernel name to boot, the first character was lost, the arg--
fix that.
Submitted by: jhay
that the driver clock is identical to the processor or bus clock.
This is the case for the PowerQUICC processor. When the clock is
high enough, overflows happen in the calculation of the time it
takes to send 1/10 of a character, used in delay loops. Fix the
overflows so as to fix bugs in the delay loops that can cause either
insufficient delays or excessive delays.
system devices (i.e. console, debug port or keyboard), don't stop
after the first match. Find them all and keep track of the last.
The reason for this change is that the low-level console is always
added to the list of system devices first, with other devices added
later. Since new devices are added to the list at the head, we have
the console always at the end. When a debug port is using the same
UART as the console, we would previously mark the "newbus" UART as
a debug port instead of as a console. This would later result in a
panic because no "newbus" device was associated with the console.
By matching all possible system devices we would mark the "newbus"
UART as a console and not as a debug port.
While it is arguably better to be able to mark a "newbus" UART as
both console and debug port, this fix is lightweight and allows
a single UART to be used as the console as well as a debug port
with only the aesthetic bug of not telling the user about it also
being a debug port.
Now that we match all possible system devices, update the rclk of
the system devices with the rclk that was obtained through the
bus attachment. It is generally true that clock information is
more reliable when obtained from the parent bus than by means of
some hardcoded or assumed value used early in the boot. This by
virtue of having more context information.
MFC after: 1 month
by driver backends to mark individual channels as enabled or not.
The default implementation of this method always mark channels as
enabled.
This method is currently not used, but is added with the PowerQUICC
in mind where the 2nd SCC channel can be disabled.
This will increase the memory consumption for more than 1 Mb, but this
is required for operation on multiinterface access concentrators running
mpd.
Requested by: Alexander Motin
