does not have a rate table in older hal's so if we scan such a
channel the driver will hit an assertion or crash; for old hal's
fallback to using the static turbo rate table for this mode
(not correct but good enough for now given none of the rate
control algorithms understand how to switch between base+boost)
Approved by: re (blanket wireless)
mode works properly, previously the hostap channel could not be changed off #3.
Fix an ifp/sc misuse while I am here.
Reported by: many
Approved by: re (bmah)
change interrupt if the link is established with link parter. However
interrupt handler didn't acknowledge the interrupt if nfe(4) was not
running at the time of interrupt delivery. This caused endless
interrupt generation. Fix the bug by acknowledging the interrupt
regardless of running state of the driver.
PR: kern/116295
Submitted by: Mark Derbyshire (mark At taom dot com)
Approved by: re (kensmith)
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
- duplicate #define in header, thanks to Kevin Lo for pointing out.
- incorrect BUSMASTER enable logic, thanks Patrick Oeschger
- 82543 fails due to bogus IO BAR logic
- Allow 82571 to use MSI interrupts
- Checksum Offload for UDP not working on 82575
Approved by:re
ioctl().
Note that other information provided by ifconfig(8) such like "list chan"
or "list ap" are still not available at this moment.
Before an(4) is connected to wlan(4), users are encouraged to use
ancontrol(8) to retrieve aforementioned information.
Reported by: dhw (http://lists.freebsd.org/pipermail/freebsd-current/2007-July/074848.html)
Reviewed by: ambrisko
Tested by: dhw
Approved by: re (bmah)
- fix the use after free seen when sending packets small enough to fit as an immediate
and bpf peers are present
- update to firmware rev 4.7 along with various small vendor fixes
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 3 days
that can lead to a panic when the stick is yanked.
- make sure that zyd_attach() returns 0 or errno.
Submitted by: Weongyo Jeong <weongyo.jeong@gmail.com>
Reported by: Ted Lindgreen <ted@tednet.nl>
Reviewed by: sam
Approved by: re (blanket wireless)
o update ic_lastdata to reflect time of last outbound frame
o outbound traffic must preempt/cancel bg scanning to avoid delays
This stuff was somehow missed in the initial import.
Reviewed by: thompsa, avatar, sephe (earlier version)
Approved by: re (blanket wireless)
The first drop was Beta, this code is expected to be the release version.
Note that this driver code will build in either 6.2 or 7. If you
use the code in 6.2 you will not get TSO or MSI/X support but it will
function in a legacy mode.
Approved by: re
needed at least to convince the BIOS to give us access to CPU freq
control on MacBooks.
Submitted by: Rui Paulo <rpaulo / fnop.net>
Approved by: re
MFC after: 5 days
ZD1211/ZD1211B USB IEEE 802.11b/g wireless network devices. Not (yet)
connected to the build process (next batch of commits once I've looped
the current back back).
Submitted by: Weongyo Jeong
Reviewed by: sam@
Approved by: re@
Both WWNN and WWPN are 64-bit unsigned integers and they are prefixed
with "0x", which requires two more bytes each.
Submitted by: Danny Braniss (danny at cs dot huji dot ac dot il)
via Matthew Jacob (lydianconcepts at gmail dot com)
Approved by: re (bmah)
MFC after: 3 days
- remove cpl->iff panic - we can't know the port number from the rspq on the 4-port
- pick the ifnet based on the interface in the CPL header
- switch to using qset 0 for egress on the 4-port for now - may change
when we start using RSS
- move ether_ifdetach to before the port lock gets deinitialized to avoid
hang in the case where there are BPF peers (cxgb_ioctl is called indirectly
when BPF peers are present)
- don't call t3_mac_reset if multiport is set, this was causing tx errors
by misconfiguring the MAC on the 4-port
- change V_TXPKT_INTF to use txpkt_intf as the interfaces are not contiguous
- free the mbuf immediately in the case where the payload is small enough to be copied
into the rspq
- only update the coalesce timer if for a queue if packets were taken off of it
- add in missed 20ms DELAY in initializaton vsc8211
- prompt MFC as this only applies to the 4-port which is currently completely
broken - OK'd by kensmith
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 0 days
on an down mxge interface
- Fix a bug where mxge reported the link state as
active when it wasn't (after ifconfig down).
- Prevent spurious watchdog resets when link partner is not consuming
- Add support for CX4 and popular XFP media detection
- Update the firmware and associated header files to 1.4.25
Approved by: re (kensmith)
and newer CPUs (including Core 2 and Core / Core 2 based Xeons). The
driver attaches to each cpu device and creates a sysctl node in that
device's sysctl context (dev.cpu.N.temperature). When invoked, the
handler binds to the appropriate CPU to ensure a correct reading.
Submitted by: Rui Paulo <rpaulo@fnop.net>
Sponsored by: Google Summer of Code 2007
Tested by: des, marcus, Constantine A. Murenin, Ian FREISLICH
Approved by: re (kensmith)
MFC after: 3 weeks
Without this the PHY wouldn't work as expected. This should fix
dual-boot Windows XP machine where RealTek Windows drivers put the
PHY in power down mode during shutdown. The magic PHY register
accesses come from RealTek driver. No datasheets mention the magic
PHY registers.
In general, the PHY wakeup code should go into PHY driver. However it
seems that it only apply to RTL8169S single chip and it would be
another hack if we have rgephy(4) check what parent driver/chip model
is attached.
Reported by: lofi, Laurens Timmermans ( laurens AT timkapel DOT nl )
Tested by: lofi
Obtained from: RealTek FreeBSD driver
Approved by: re (Ken Smith)
- Don't leak the config lock if detach() fails due to the controller char
dev being open.
- Close a race between detach() and a process opening the controller char
dev.
MFC after: 1 week
Approved by: re (bmah)
Fix a resource allocation bug (explained by jhb on -acpi)
Thanks for Mike Tancsa for testing and helping track down the bug.
Approved by: re (kensmith)
MFC after: 3 weeks
detailed status on each of the backing subdisks. This allows userland
to see which subdisks are online, failed, missing, or a hot spare.
MFC after: 1 week
Approved by: re (bmah)
Reviewed by: sos
differ in their details with calls to a new function, ehci_hcreset(),
that performs the reset.
The original sequences either had no delay or a 1ms delay between
telling the controller to stop and asserting the controller reset
bit. One instance of the original reset sequence waited for the
controller to indicate that its reset was complete before continuing,
but the other two immediately let the subsequent code execute. The
latter is a problem on some hardware, because a read of the HCCPARAMS
register returns an incorrect value while the reset is in progress,
which triggers an infinite loop in ehci_pci_givecontroller(), which
hangs the system on shutdown.
The reset sequence in ehci_hcreset() starts with the most complete
instance from the original code, which contains a loop to wait for
the controller to indicate that its reset is complete. This appears
to be the correct thing to do according to "Enhanced Host Controller
Interface Specification for Universal Serial Bus" revision 1.0,
section 2.3.1. Add another loop to wait for the controller to
indicate that it has stopped before setting the HCRESET bit. This
is required by the section 2.3.1 in the specification, which says
that setting HCRESET before the controller has halted "will result
in undefined behaviour".
Reviewed by: imp (previous patch version without the extra wait loop)
Tested by: se (previous patch version without the extra wait loop)
Approved by: re (bmah)
MFC after: 1 week
