Rather than enabling the I/O MMU when the vmm module is loaded,
defer initialization until the first attempt to pass a PCI device
through to a guest. If the I/O MMU fails to initialize or is not
present, than fail the attempt to pass a PCI device through to a
guest.
The hw.vmm.force_iommu tunable has been removed since the I/O MMU is
no longer enabled during boot. However, the I/O MMU support can be
disabled by setting the hw.vmm.iommu.enable tunable to 0 to prevent
use of the I/O MMU on any systems where it is buggy.
Reviewed by: grehan
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D7448
need to include it explicitly when <vm/vm_param.h> is already included.
Suggested by: alc
Reviewed by: alc
Differential Revision: https://reviews.freebsd.org/D5379
Some external tools just do a 'ls /dev/vmm' to figure out the bhyve virtual
machines on the host. These tools break if the devmem device nodes also
appear in /dev/vmm.
Requested by: grehan
Previously this was done by the caller of 'svm_launch()' after it returned.
This works fine as long as no code is executed in the interim that depends
on pcpu data.
The dtrace probe 'fbt:vmm:svm_launch:return' broke this assumption because
it calls 'dtrace_probe()' which in turn relies on pcpu data.
Reported by: avg
MFC after: 1 week
devmem is used to represent MMIO devices like the boot ROM or a VESA framebuffer
where doing a trap-and-emulate for every access is impractical. devmem is a
hybrid of system memory (sysmem) and emulated device models.
devmem is mapped in the guest address space via nested page tables similar
to sysmem. However the address range where devmem is mapped may be changed
by the guest at runtime (e.g. by reprogramming a PCI BAR). Also devmem is
usually mapped RO or RW as compared to RWX mappings for sysmem.
Each devmem segment is named (e.g. "bootrom") and this name is used to
create a device node for the devmem segment (e.g. /dev/vmm/testvm.bootrom).
The device node supports mmap(2) and this decouples the host mapping of
devmem from its mapping in the guest address space (which can change).
Reviewed by: tychon
Discussed with: grehan
Differential Revision: https://reviews.freebsd.org/D2762
MFC after: 4 weeks
execution control and writing the difference between the host TSC and
the guest TSC into the TSC offset in the VMCS upon encountering a
write.
Reviewed by: neel
after decoding the instruction matches the one provided by hardware.
Prior to r283293 'vie->num_valid' used to contain the actual length of
the instruction whereas now it contains the maximum instruction length
possible. This introduced a bug when calculating a RIP-relative base address.
Fix this by using 'vie->num_processed' rather than 'vie->num_valid' as the
length of the emulated instruction.
Reported and tested by: tychon
MFC after: 1 week
"sleeping" state. This is done by forcing the vcpu to transition to "idle"
by returning to userspace with an exit code of VM_EXITCODE_REQIDLE.
MFC after: 2 weeks
have an accurate length on an EPT violation. This is not needed by the
instruction decoding code because it also has to work with AMD/SVM that
does not provide a valid instruction length on a Nested Page Fault.
In collaboration with: Leon Dang (ldang@nahannisys.com)
Discussed with: grehan
MFC after: 1 week
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
Prior to this change both functions returned 0 for success, -1 for failure
and +1 to indicate that an exception was injected into the guest.
The numerical value of ERESTART also happens to be -1 so when these functions
returned -1 it had to be translated to a positive errno value to prevent the
VM_RUN ioctl from being inadvertently restarted. This made it easy to introduce
bugs when writing emulation code.
Fix this by adding an 'int *guest_fault' parameter and setting it to '1' if
an exception was delivered to the guest. The return value is 0 or EFAULT so
no additional translation is needed.
Reviewed by: tychon
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D2428
- Must-Be-Zero bits cannot be set.
- EFER_LME and EFER_LMA should respect the long mode consistency checks.
- EFER_NXE, EFER_FFXSR, EFER_TCE can be set if allowed by CPUID capabilities.
- Flag an error if guest tries to set EFER_LMSLE since bhyve doesn't enforce
segment limits in 64-bit mode.
MFC after: 2 weeks
Do the same when transitioning a vector from the IRR to the ISR and also
when extinguishing it from the ISR in response to an EOI.
Reported by: Leon Dang (ldang@nahannisys.com)
MFC after: 2 weeks
losing time.
The problem with the earlier implementation was that the uptime value
used by 'vrtc_curtime()' could be different than the uptime value when
'vrtc_time_update()' actually updated 'base_uptime'.
Fix this by calculating and updating the (rtctime, uptime) tuple together.
MFC after: 2 weeks
to the Intel SDM vectors 16 through 255 are allowed to be delivered via the
local APIC.
Reported by: Leon Dang (ldang@nahannisys.com)
MFC after: 2 weeks
%rdi, %rsi, etc are inadvertently bypassed along with the check to
see if the instruction needs to be repeated per the 'rep' prefix.
Add "MOVS" instruction support for the 'MMIO to MMIO' case.
Reviewed by: neel
code segment base address.
Also if an instruction doesn't support a mod R/M (modRM) byte, don't
be concerned if the CPU is in real mode.
Reviewed by: neel
This makes FreeBSD guest to not avoid using LAPIC timer, preferring HPET
due to worries about non-existing for virtual CPUs deep sleep states.
Benchmarks of usleep(1) on guest and host show such extra latencies:
- 51us for virtual HPET,
- 22us for virtual LAPIC timer,
- 22us for host HPET and
- 3us for host LAPIC timer.
MFC after: 2 weeks
- fix warning about comparison of 'uint8_t v_tpr >= 0' always being true.
- fix error triggered by an empty clobber list in the inline assembly for
"clgi" and "stgi"
- fix error when compiling "vmload %rax", "vmrun %rax" and "vmsave %rax". The
gcc assembler does not like the explicit operand "%rax" while the clang
assembler requires specifying the operand "%rax". Fix this by encoding the
instructions using the ".byte" directive.
Reported by: julian
MFC after: 1 week
Allow the ppt driver to attach to devices that were hinted to be
passthrough devices by the PCI code creating them with a driver
name of "ppt".
Add a tunable that allows the IOMMU to be forced to be used. With
SR-IOV passthrough devices the VFs may be created after vmm.ko is
loaded. The current code will not initialize the IOMMU in that
case, meaning that the passthrough devices can't actually be used.
Differential Revision: https://reviews.freebsd.org/D73
Reviewed by: neel
MFC after: 1 month
Sponsored by: Sandvine Inc.
capability of VT-x. This lets bhyve run nested in older VMware versions that
don't support the PAT save/restore capability.
Note that the actual value programmed by the guest in MSR_PAT is irrelevant
because bhyve sets the 'Ignore PAT' bit in the nested PTE.
Reported by: marcel
Tested by: Leon Dang (ldang@nahannisys.com)
Sponsored by: Nahanni Systems
MFC after: 2 weeks
