First, we were never correctly checking for a 24XX Status Type 0
response- that cased us to fall through to evaluate status for
commands as if this were a 2100/2200/2300 Status Type 0 response.
This is *close*, but not quite the same. This has been reported
to be apparent with some wierd lun configuration problems with
some arrays. It became glaringly apparent on sparc64 where none
of the correct byte swap things were done.
Fixing this omission then caused a whole universe shifting debug
cycle of endian issues for the 2400. The manual for 24XX f/w turns
out to be wrong about the endianness of a couple of entities. The
lun and cdb fields for the type 7 request are *not* unconditionally
big endian- they happen to be opposite of whatever the endian of
the current machine type is. Same with the sense data for the
24XX type 0 response.
While we're at it investigate and resolve some NVRAM endian
issues.
Approved by: re (ken)
MFC after: 3 days
When the linux port changes were imported which split the
target command list to be separate from the initiator command
list and the handle format changed to encode a type in the handle
the implications to the function isp_handle_index (which only
the NetBSD/OpenBSD/FreeBSD ports use) were overlooked.
The fault is twofold: first, the index into the DMA maps
in isp_pci is wrong because a target command handle with
the type bit left in place caused a bad index (and panic)
into dma map. Secondly, the assumption of the array
of DMA maps in either PCS or SBUS attachment structures is
that there is a linear mapping between handle index and
DMA map index. This can no longer be true if there are
overlapping index spaces for initiator mode and target
mode commands.
These changes bandaid around the problem by forcing us
to not have simultaneous dual roles and doing the appropriate
masking to make sure things are indexed correctly. A longer
term fix is being devloped.
and provied an isp_control entry point so that the outer layers can
do PLOGI/LOGO explicitly. Add MS IOCB support. This completes the cycle
for base support for SMI-S.
Only complain about FC Reponse errors if they're nonzero.
Shorten some PortID printouts for local loop.
Add an internal isp_xcmd_t data structure which we'll use for some
CT-Passthru support as part of adding SMI-S.
gone device timers and zombie state entries. There are tunables
that can be used to select a number of parameters.
loop_down_limit - how long to wait for loop to come back up before
declaring
all devices dead (default 300 seconds)
gone_device_time- how long to wait for a device that has appeared
to leave the loop or fabric to reappear (default 30 seconds)
Internal tunables include (which should be externalized):
quick_boot_time- how long to wait when booting for loop to come up
change_is_bad- whether or not to accept devices with the same
WWNN/WWPN that reappear at a different PortID as being the 'same'
device.
Keen students of some of the subtle issues here will ask how
one can keep devices from being re-accepted at all (the answer
is to set a gone_device_time to zero- that effectively would
be the same thing).
the notify structs. Fix messages in isp_got_msg_fc to print out the
loop id of the sender- not the wwpn which will be synthesized later,
if possible, in the outer layers. Put in debug printouts to pair
a notify ack to a notify so one can see the start/close of an
immediate notify event. Put in spsace for TASK MANAGEMENT response
flags (which we don't do yet).
FreeBSD repository and to clean up the license header so as to
not pollute the license with file function.
Zero all mailbox structures prior to use (just in case). Change
the outgoing mailbox count for INIT_FIRMWARE to be correct.
to getting rid u_int for uint and so on).
b) Turn back on 64 bit DAC support. Cheeze it a bit in that we have two
DMA callback functions- one when we have bus_addr_t > 4 bits in width and
the other which should be normal. Even Cheezier in that we turn off setting
up DMA maps to be BUS_SPACE_MAXADDR if we're in ISP_TARGET_MODE. More work
on this in a week or so.
c) Tested under amd64 and 1MB DFLTPHYS, sparc64, i386 (PAE, but insufficient
memory to really test > 4GB). LINT check under amd64.
MFC after: 1 month
