subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
- Remove __RMAN_RESORUCE_VISIBLE again. It's no longer required either
because of the above change or because struct rman is no longer hidden.
Reviewed by: grehan
Tested by: cross-compile on i386
to allow dumping per-thread machine specific notes. On ia64 we use this
function to flush the dirty registers onto the backingstore before we
write out the PRSTATUS notes.
Tested on: alpha, amd64, i386, ia64 & sparc64
Not tested on: arm, powerpc
being defined, define and use a new MD macro, cpu_spinwait(). It only
expands to something on i386 and amd64, so the compiled code should be
identical.
Name of the macro found by: jhb
Reviewed by: jhb
and setting MSR. This was most evident with the idle proc running
with interrupts disabled and causing a lockup. Switch over to the
i386 style which does things in the right order.
debug assisted by: gallatin, and the invaluable KTR option.
their own directory and module, leaving the MD parts in the MD
area (the MD parts _are_ part of the modules). /dev/mem and /dev/io
are now loadable modules, thus taking us one step further towards
a kernel created entirely out of modules. Of course, there is nothing
preventing the kernel from having these statically compiled.
those architectures without pmap locking.
- Eliminate the acquisition and release of Giant from vm_map_protect().
(Translation: mprotect(2) runs to completion without touching Giant on
alpha, amd64, i386 and ia64.)
dereference curthread. It is called only from critical_{enter,exit}(),
which already dereferences curthread. This doesn't seem to affect SMP
performance in my benchmarks, but improves MySQL transaction throughput
by about 1% on UP on my Xeon.
Head nodding: jhb, bmilekic
addend of 0. This isn't correct, and was quite easy to break by
referring to the address of an element within a structure.
However, fixing this exposed the fact that symbol lookups for
local variables were returning the base of the section they
were contained in. This case is detected by comparing the return
value from elf_lookup() to the relocbase+addend value: if it is
lesser, but greater than relocbase, then relocbase+addend is
taken to be the authoritative value.
bug reported by: gallatin
and saved link register as per the ABI call sequence. Update code
that uses this (fork_trampoline etc) to use the correct genassym'd
offsets.
This fixes the 'invalid LR' message when backtracing kernel
threads in DDB.
the thread ID and call db_trace_thread().
Since arm has all the logic in db_stack_trace_cmd(), rename the
new DB_COMMAND function to db_stack_trace to avoid conflicts on
arm.
While here, have db_stack_trace parse its own arguments so that
we can use a more natural radix for IDs. If the ID is not a thread
ID, or more precisely when no thread exists with the ID, try if
there's a process with that ID and return the first thread in it.
This makes it easier to print stack traces from the ps output.
requested by: rwatson@
tested on: amd64, i386, ia64
gcc is using. This fixes devstat consumers (like vmstat, iostat,
systat) so they don't print crazy zillion digit numbers for
disk transfers and bandwidth.
According to gcc, long doubles are 64-bits, rather than 128 bits
like the SVR4 ABI spec wants them to be.. Note that MacOSX also treats
long doubles as 64-bits, and not 128 bits, so we are in good company.
Reviewed by: das
Approved by: grehan
pmap_protect() and pmap_remove(). In general, they require the lock in
order to modify a page's pv list or flags. In some cases, however,
pmap_protect() can avoid acquiring the lock.
- ddb -> db for low-level trapcode
- implement makectx. I think it only matters that the stack is setup
correctly.
- bring over ddb_trap_glue and rename to db_trap_glue
