prism2 flag in pccard.conf, but I'm leaving it place for the moment in
case the small sample of PrismII cards that I've tried is not
representative.
MFC After: 30 days
Obtained from: NetBSD
pccard layer and rename them PCMCIA_CARD and PCMCIA_CARD2 respectively
(note, this is being done with an eye towards NetBSD integreation so
it is easier to keep lists of cards between us and them in sync).
Use this in the an and wi drivers.
trying something new with the macros here and will likely try to get
them adopted by NetBSD as well as moving them to other drivers. They
make the list more compact and easier to read, the price of rigid to a
schema for generating them (of course there are those that would argue
this isn't bad).
Obtained from: NetBSD's if_wi_pcmcia.c 1.9
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
go into the PLX 9052's interrupt control register and turn on the magic
interrupt enable bit.
Partial thanks are due to OpenBSD for pointing out that the chip is a
PLX 9052 and pointing me to the datasheet PDF.
It appears that a number of PrismII card vendors seem to be doing the
same thing (that is, using the same PCI bridge chip) to support PCI,
but each with their own vendor/product ID. So rather than cut-n-paste
another if statement into the probe routine, it's probably better to
provide support for a table. Adding new devices will be a lot easier
that way.
despite the fact that most people want to set exactly the same settings
regardless of which card they have. It has been repeatidly suggested
that this configuration should be done via ifconfig. This patch
implements the required functionality in ifconfig and add support to the
wi and an drivers. It also provides partial, untested support for the
awi driver.
PR: 25577
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
a LinkSys card here in the office where reading the station address
fails the first time, but works find afterwards. Without this, the
probe fails. I don't think this will negatively impact any existing
cards, but I want to confirm this before MFC'ing.
s/1518/ETHER_MAX_LEN
Some style changes, add some braces, mostly residual from having
a lot of debug hooks added while working on this driver.
Bring in a plethora of changes from NetBSD:
revision 1.58
date: 2001/03/08 11:07:08; author: ichiro; state: Exp; lines: +17 -1
it wait until busy flag disappears.
it was able to prevent some cards with late initializing faling in wi_reset().
revision 1.41
date: 2000/10/13 19:15:08; author: jonathan; state: Exp; lines: +4 -2
Fix wi_intr() to avoid touching card registers during insert/remove events,
when sharing an interrupt with other devices:
check sc->sc_enabled, and drop the interrupt if its' off.
revision 1.30
date: 2000/08/18 04:11:48; author: jhawk; state: Exp; lines: +4 -4
Copy wi_{dst,src}_addr from struct wi_frame into faked-up ether_header
instead of addr1 and addr2. THis means that tcpdump -e will show the
correct MAC address for communications with access points instead of showing
the BSSID.
In the future there should be 802.11 support for bpf/libpcap/tcpdump,
but that is aways down the road.
o Change the number of init tries from 5 to a #define.
o Allow up to 5s rather than 2s for commands to complete. This
is still much less than 51 minutes, but makes my intel card init
with more reliability than before.
Don't leak iospace when irq allocation fails. (call wi_free())
Call bus_release_resource() with the correct "rid" obtained from
bus_alloc_resource() that's saved in the softc instead of a hardcoded
0.
It appears that some of the new PRISM2 cards need it.
Fail the probe if we fail to read the MAC address.
Fix a comment.
Delete the unload printf. The bus system now prints this message.
a #defined constant, wrap a few long lines, etc... Also remove stupid
'all your base are belong to us' joke from comment that I don't really
care to see immortalized in the source tree.
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
<sys/proc.h> to <sys/systm.h>.
Correctly document the #includes needed in the manpage.
Add one now needed #include of <sys/systm.h>.
Remove the consequent 48 unused #includes of <sys/proc.h>.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
