The presence or absence of a keyboard does not change whether an
UART is designed as a keyboard port or not and thus whether we
can use the port as a TTY or not.
We now call sunkbd_attach() even when we didn't previously find
a keyboard. Emit a useful message stating that no keyboard was
found, but don't do anything else.
MFC after: 5 days
ServeRAID 4 - 7 models right now. Support for older cards is possible, but
I don't have any hardware to experiment with.
Thanks to Jack Hammer at Adaptec for providing debugging hints.
Sponsored by: ImproWare AG, Switzerland
engineering the pending interrupt sources from the current
state of the controller. For channel A we can always read the
interrupt pending register (RR3). For channel B we can read
the interrupt vector register (RR2) because it contains the
modified vector and thus includes the interrupt source.
Since we currently need puc(4) for the Z8530, we know that
the interrupt handler for both channels will be called and
thus that RR3 will always be read at least once, even if ch A
has no pending interrupt.
NOTE: The modified interrupt vector has no value that represent
a lack of pending interrupt for channel B. That is, the
value read when no interrupts are pending is the same as the
value for the special receive condition. Fortunately, we don't
actually have to depend on that interrupt source. This does
mean that we need to properly handle the overflow condition,
when we read received character from the chip.
o The DSR signal is represented by the SYNC bit in the external
status register (RR0). We now properly track DSR.
o It's save to enable the external/status interrupt source. We
now get interrupts when line signals (DSR, DCD or CTS) change.
Problems fixes:
o interrupt storms.
o blocked open(2).
o lack of (hardware) flow control.
o unable to report DSR.
MFC after: 5 days
providing special version of CDIOCREADSUBCHANNEL ioctl(), which assumes that
result has to be placed into kernel space not user space. In the long run
more generic solution has to be designed WRT emulating various ioctl()s
that operate on userspace buffers, but right now there is only one such
ioctl() is emulated, so that it makes little sense.
MFC after: 2 weeks
thought. I'm unsure why I thought this was the case, but it
definitely isn't for this card. If another card with the other ID
makes an appearance, then we'll add a second entry for it.
# With this change my Olicom OC2220 is now working again, since I make
# this commit with that device. :-)
EtherJet, the interrupt is selected in the eeprom based on the layout
of the PC Card board. Since this is encoded into the EEPROM, and has
no relationship to the IRQ that the pccard bridge routes the PC Card's
interrupt pin to.
As such, stop writing to that register. This gets my EtherJet working.
# The eeprom reading code appears to be totally wrong for my EtherJet
# card. This causes the card to bogusly detect the media options
# available.
significant clean up and optimizations:
- don't call bioq_disksort() on every command, the hardware will do that for
us.
- remove all of the complicated bio deferral code. bio's that can't be
serviced immediately can just wait on the bioq.
- Only reserve one command object for doing control commands to the card.
This simplifies a lot of code and significantly reduces the size of the
command struct.
- Allocate commands out of a slab instead of embedding them into the softc.
- Call the command action method directly instead of having ips_get_free_cmd()
call it indirectly.
MFC After: 1 week
null-modem tty device emulate the speed settings faithfully.
The speed is emulated independently for the two directions, using
the slower of the local sides ispeed and the remote sides ospeed.
The emulated speed takes settings of bits/char, parity and stopbit
into account.
Inspired by: The BSD-DK Editor Celebrity Deathmatch Contest
the interface when going to toggle VLAN support for
internal reasons. If the IFCAP_VLAN_HWTAGGING bit is
cleared, we should rely on the (re)init routine to turn
VLAN support off and never touch the relevant hardware bits.
This applies to other capability bits, too. The user
obviously has a reason for clearing a capability bit,
e.g., if his particular NIC is buggy and hangs if a
certain hardware capability is turned on even for a
fraction of a second.
The flag adapter->em_insert_vlan_header still is set or
reset irrespective of the IFCAP_VLAN_HWTAGGING setting,
as before, in order to handle the case when a user sets
promiscuous mode on an interface first and later turns
its IFCAP_VLAN_HWTAGGING bit on.
This change might look orthogonal to rev#1.85, but in fact
it is not. It introduces bugfixes that hopefully will make
implementing the general scheme mentioned in the commit
message of rev#1.85 easier.
configuration: it appears to work properly in the non-promiscuous case, but
we've not yet implemented a more general solution that maintains full
functionality with promiscuous mode enabled. While my hope is that we can
get one implemented soon, this will improve functionality substantially in
the mean time.
MFC after: 3 days
AX88190 ones, but that one only minorly):
o don't set flags in the match routine. They appear to be cleared
when probe/attach is called. Before this change, they were
always treated as a simple ne2000, which would fail to get the
right NIC address.
o Lookup device again in the probe routine and probe based on the
cards that you see.
o Detect and report the DL10022 seprately from the DL10019 cards.
While I'm here:
o remove a bad printf
o change another bad printf to device_printf.
o minor style(9) formatting tweaks.
# note: a lot of OEM entries are in the ed_pccard_products such that we can
# likely remove, or collapse, many of them.
This makes all of my DL100xx cards at least probe the ethernet address
correctly, which it wasn't doing before. I can't seem to locate my
AX88xxx based cards, so those haven't been tested, but they were
busted before the change so they can't be any worse now...
address, and additional information. Then the printing of the
ethernet address was moved into ether_attach, and so we were printing
orphaned information about the card. Now the probe message is
prefixed by edX:. Prepare for it to move under bootverbose, but don't
move it there yet (the || 1 trick).
versions of the Racore PC Card Ethernet card. Rearrange to reflect
this reality. This ejects IODATA from 0x1bf, which belongs to Racore.
Thanks to Wilko for providing me with a dumpcis for the DEPCM card.
Also, added Nextcom Nexthawk card from NetBSD
o mark rx frames including FCS in the payload with the
IEEE80211_RADIOTAP_F_FCS flag
o remove hack to copy 802.11 headers with padding out of line; instead mark
the frames with IEEE80211_RADIOTAP_F_DATAPAD and require applications to
do the work
o split precalculated radiotap flags into tx+rx now that they can be different
Note the full usefulness of these changes depends on updates to applications
that process radiotap data.
o don't reclaim any previous beacon state in ath_beacon_alloc; do it
explicitly in ath_newstate
o reference count the node held in the beacon frame state block
o process ibss merge more intelligently; let the state machine do the
right thing instead of explicitly setting the new bssi id
o explicitly stop tx dma before doing beacon setup to handle the ibss
merge case
