Resolving CPU windows from localbus entry caused buffer overflow
and memory corruption. Fix wrong indexing and ensure the index
does not exceed table size.
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D10720
Marvell Armada 380 is a uni-processor variant of the 38x SoC
family. A function platform_mp_setmaxid() was setting a hardcoded
value, which caused boot fail on A380. Fix this by relying on
the CPU count obtained from device tree nodes.
Submitted by: Marcin Wojtas <mw@semihalf.com
Obtained from: Semihalf
Sponsored by: Netgate
Reviewed by: loos
Differential revision: https://reviews.freebsd.org/D10783
Before the fix for single interrupt, both percpu and non-percpu routes
were enabled/disable at the same time.
Submitted by: Marcin Wojtas <mw@semihalf.com
Obtained from: Semihalf
Sponsored by: Stormshield, Netgate
Reviewed by: loos
Differential revision: https://reviews.freebsd.org/D10716
For all Marvell devices, MBUS windows configuration is done
in a common place. Only CESA was an exception, so move its
related code from driver to mv_common.c. This way it uses
same proper DRAM information, same as all other interfaces
instead of parsing DT /memory node directly.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: loos
Differential revision: https://reviews.freebsd.org/D10723
consistent and easier to read.
While here, remove two unused static functions and fix a unused function
warning when building !INTRNG.
No functional changes.
Sponsored by: Rubicon Communications, LLC (Netgate)
If MPIC happens to be a slave interrupt controller (as on Armada38x),
it should be attached after primary interrupt controller.
Thus BUS_PASS_ORDER_LATE was added to default BUS_PASS_INTERRUPT.
This change doesn't affect the cases when MPIC is standalone IC.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield, Netgate
Reviewed by: loos
Differential revision: https://reviews.freebsd.org/D10715
OF_finddevice doesn't find the "simple-bus" node, which is problematic
for Marvell platforms, using nested buses in Device Tree, like
Armada 38x SoC.
Submitted by: Arnaud Ysmal <arnaud.ysmal@stormshield.eu>
Obtained from: Stormshield
Sponsored by: Stormshield
Reviewed by: loos
Differential revision: https://reviews.freebsd.org/D10719
sdhci_fdt.
Enable the SDHCI controller, bus and devices on ARMADA38X kernel.
Tested on: ClearFog Pro
Reviewed by: Marcin Wojtas <mw at semihalf.com>
Sponsored by: Rubicon Communications, LLC (Netgate)
Differential Revision: https://reviews.freebsd.org/D10606
Tested on: ClearFog Pro
Reviewed by: Marcin Wojtas <mw at semihalf.com>
Sponsored by: Rubicon Communications, LLC (Netgate)
Differential Revision: https://reviews.freebsd.org/D10601
Add early init handler, which comprises various internal
bus optimisations for Armada 38x SoC's. Magic values used
due to undocumented registers.
Submitted by: Marcin Wojtas <mw@semihalf.com>,
Arnaud Ysmal <arnaud.ysmal@stormshield.eu>
Obtained from: Semihalf, Stormshield
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D10219
Introduce machine-dependent part of the arm/pl310 driver for
Armada 38x SoCs. Add prefetch and power savings configuration.
Submitted by: <arnaud.ysmal@stormshield.eu>
Obtained from: Stormshield
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D10220
It seems to be old code from the armv6 project branch that never had a
kernel config.
Reviewed by: mmel
Sponsored by: ABT Systems Lrd
Differential Revision: https://reviews.freebsd.org/D7166
Convert PCIe hot plug support over to asking the firmware, if any, for
permission to use the HotPlug hardware. Implement pci_request_feature
for ACPI. All other host pci connections to allowing all valid feature
requests.
Sponsored by: Netflix
- Use new option SMP_ON_UP instead of (mis)using specific CPU type.
By this, any SMP kernel can be compiled with SMP_ON_UP support.
- Enable runtime detection of CPU multiprocessor extensions only
if SMP_ON_UP option is used. In other cases (pure SMP or UP),
statically compile only required variant.
- Don't leak multiprocessor instructions to UP kernel.
- Correctly handle data cache write back to point of unification.
DCCMVAU is supported on all armv7 cpus.
- For SMP_ON_UP kernels, detect proper TTB flags on runtime.
Differential Revision: https://reviews.freebsd.org/D9133
Commit r312747 ("Setup decoding windows for ARMADA38X") resulted
in build failing for Marvell platforms, which don't have AHCI controller.
This patch provides a fix by adding dummy functions for such cases.
On the occasion rename register dump routine to decode_win_ahci_dump,
in order to avoid confusion.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
This file provides support for AHCI mode on Armada38x
and adds new optional AHCI device to arm/mv/files.mv.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9222
It is necesarry to open memory windows on internal bus for
AHCI driver to work correctly.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9220
Configure decoding windows only for devices with
enabled nodes in FDT.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9219
* Currently supports only Armada38X family but other Marvell SoC's
can be added if needed.
* Provides temperature is C deg.
* To print the temperature one can use:
sysctl dev.armada_thermal.0.temperature
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D9217
Replace archaic "busses" with modern form "buses."
Intentionally excluded:
* Old/random drivers I didn't recognize
* Old hardware in general
* Use of "busses" in code as identifiers
No functional change.
http://grammarist.com/spelling/buses-busses/
PR: 216099
Reported by: bltsrc at mail.ru
Sponsored by: Dell EMC Isilon
for later Cortex-A CPUs that support the Multiprocessor Extensions. This
will be needed to support both in a single GENERIC kernel while still
being able to only build for a single SoC.
Reviewed by: mmel
Relnotes: yes
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D8138
Check if there is a second CESA SRAM node in FDT and add a CPU window
for it. Define A38X specific macro for setting device attribute for
each node.
Submitted by: Michal Stanek <mst@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D6216
On other platforms with CESA accelerator the SRAM memory is mapped in
early init before driver is attached. This method only works correctly
with mappings no smaller than L1 section size (1MB). There may be more
SRAM blocks and they may have smaller sizes than 1MB as is the case
for Armada38x. Instead, map SRAM memory with bus_space_map() in CESA
driver attach. Note that we can no longer assume that VA == PA for the
SRAM.
Submitted by: Michal Stanek <mst@semihalf.com
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D6215
have ACLE support built in. The ACLE (ARM C Language Extensions) defines
a set of standardized symbols which indicate the architecture version and
features available. ACLE support is built in to modern compilers (both
clang and gcc), but absent from gcc prior to 4.4.
ARM (the company) provides the acle-compat.h header file to define the
right symbols for older versions of gcc. Basically, acle-compat.h does
for arm about the same thing cdefs.h does for freebsd: defines
standardized macros that work no matter which compiler you use. If ARM
hadn't provided this file we would have ended up with a big #ifdef __arm__
section in cdefs.h with our own compatibility shims.
Remove #include <machine/acle-compat.h> from the zillion other places (an
ever-growing list) that it appears. Since style(9) requires sys/types.h
or sys/param.h early in the include list, and both of those lead to
including cdefs.h, only a couple special cases still need to include
acle-compat.h directly.
Loves it: imp
where possible. In the places that doesn't work (multi-line inline asm,
and places where the old armv4 cpufuncs mechanism is used), annotate the
accesses with a comment that includes SCTLR. Now a grep -i sctlr can find
all the system control register manipulations.
No functional changes.
After r285994, sysctl(8) was fixed to use 273.15 instead of 273.20 as 0C
reference and as result, the temperature read in sysctl(8) now exibits a
+0.1C difference.
This commit fix the kernel references to match the reference value used in
sysctl(8) after r285994.
Sponsored by: Rubicon Communications (Netgate)
needed in later changes where we may not be able to lock the pic list lock
to perform a lookup, e.g. from within interrupt context.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
struct associated with some type defined in enum intr_map_data_type
must have struct intr_map_data on the top of its own definition now.
When such structs are used, correct type and size must be filled in.
There are three such structs defined in sys/intr.h now. Their
definitions should be moved to corresponding headers by follow-up
commits.
While this change was propagated to all INTRNG like PICs,
pic_map_intr() method implementations were corrected on some places.
For this specific method, it's ensured by a caller that the 'data'
argument passed to this method is never NULL. Also, the return error
values were standardized there.
rounddown2 tends to produce longer lines than the original code
and when the code has a high indentation level it was not really
advantageous to do the replacement.
This tries to strike a balance between readability using the macros
and flexibility of having the expressions, so not everything is
converted.
universal.
(1) New struct intr_map_data is defined as a container for arbitrary
description of an interrupt used by a device. Typically, an interrupt
number and configuration relevant to an interrupt controller is encoded
in such description. However, any additional information may be encoded
too like a set of cpus on which an interrupt should be enabled or vendor
specific data needed for setup of an interrupt in controller. The struct
intr_map_data itself is meant to be opaque for INTRNG.
(2) An intr_map_irq() function is created which takes an interrupt
controller identification and struct intr_map_data as arguments and
returns global interrupt number which identifies an interrupt.
(3) A set of functions to be used by bus drivers is created as well as
a corresponding set of methods for interrupt controller drivers. These
sets take both struct resource and struct intr_map_data as one of the
arguments. There is a goal to keep struct intr_map_data in struct
resource, however, this way a final solution is not limited to that.
(4) Other small changes are done to reflect new situation.
This is only first step aiming to create stable interface for interrupt
controller drivers. Thus, some temporary solution is taken. Interrupt
descriptions for devices are stored in INTRNG and two specific mapping
function are created to be temporary used by bus drivers. That's why
the struct intr_map_data is not opaque for INTRNG now. This temporary
solution will be replaced by final one in next step.
Differential Revision: https://reviews.freebsd.org/D5730
separate driver. Add support for activating clock and hwreset resources
for these devices when the EXT_RESOURCES option is present.
Reviewed by: andrew, mmel, Emmanuel Vadot <manu@bidouilliste.com>
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5749
This commit provides attachment of xhci-platform for A38X boards, making
it possible to mount FreeBSD world from USB3.0 flash. 'xhci' device was
added to files.mv (as optional) and kernconf of Armada38x was enhanced.
It was also necessary to open programmable memory windows of USB3.0.
fdt_win_setup needed improvement so it's able to traverse through
children of internal-regs node.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: hselasky
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D5031
After ARM_INTRNG introduction, MPIC code needed several modifications:
- IRQ resource and its handler added
- several DEVMETHODs of INTRNG interface implemented
- defines enhanced to ensure code compiles as well for AXP as for A38X
- added dummy MSI_IRQ, ERR_IRQ defines for Armada38x
- MPIC driver was added to files.armada38x, ARM_INTRNG option enabled in
kernconf file and regs of MPIC corrected in dts file.
Instead of modifying Armada38X DTS, offsets to CPU registers defined in
driver were changed. That required restoring 'reg' property of mpic node
in ArmadaXP to state compliant with Linux DTS.
Additionally, required ARM_INTRNG definitions were added to mv_common.c.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: adrian, andrew, ian, skra
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D5030
Use u_long instead of uint32_t variables to avoid overflow
in case of PA space bigger than 32-bit.
Obtained from: Semihalf
Submitted by: Michal Stanek <mst@semihalf.com>
Sponsored by: Annapurna Labs
Approved by: cognet (mentor)
Reviewed by: andrew, br, wma
Differential revision: https://reviews.freebsd.org/D5393
intr_pic_init_secondary. Replace them with a direct call. On BCM2836
and ARMADA XP we need to add this function, but it can be empty.
Reviewed by: ian, imp
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5460
slightly wrong on the others. We should just check if mp_ncpus is set to
more than one CPU as we may wish to run on a single core even when SMP is
available.
Reviewed by: ian
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5458
Only L2 PIPT cache is supported for __ARM_ARCH >= 6.
In fact, this is just a pure proclamation as this option is used
only in armv4 specific files now.
This simplifies checking for default resource range for bus_alloc_resource(),
and improves readability.
This is part of, and related to, the migration of rman_res_t from u_long to
uintmax_t.
Discussed with: jhb
Suggested by: marcel
Marvell twsi part, however uses different register locations, as such split
the existing driver into Marvell and Allwinner attachments.
While here clean a few style issues.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4846
Summary:
Migrate to using the semi-opaque type rman_res_t to specify rman resources. For
now, this is still compatible with u_long.
This is step one in migrating rman to use uintmax_t for resources instead of
u_long.
Going forward, this could feasibly be used to specify architecture-specific
definitions of resource ranges, rather than baking a specific integer type into
the API.
This change has been broken out to facilitate MFC'ing drivers back to 10 without
breaking ABI.
Reviewed By: jhb
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5075
This is a stub for PMSU driver. Note that it cannot be used to set the
secondary core boot address during attach because drivers are attached
later than SI_SUB_CPU sysinit where cores are started.
Setting the boot address should be done manually in platform_mp_start_ap().
SMP is working fine with this commit and was enabled in Armada38x kernel
configuration file.
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4427
- Add file sys/arm/mv/armada38x/armada38x_mp.c
- Set mp_maxid and mp_ncpus based on FDT unless SCU register indicates
only one core
- Boot CPU1 in platform_mp_start_ap()
- IPI range defined
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4426
CPU1 is halted in bootROM code while it is waiting to be released.
Memory window to bootROM must be opened before booting the core.
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4425
With this commit, watchdog is supported only in case of having
"mrvl,has-wdt" property or dedicated for watchdog compatibility field
("marvell,armada-380-wdt"). There is no need to modify dts files,
as "has-wdt" property already exists.
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4424
A38X watchdog support was implemented in sys/arm/mv/timer.c driver.
It required following modifications:
- add "marvell,armada-380-wdt" compatibility, which supports only watchdog
- correct and enhance definitions related to timer control register
- unmask reset capability in RSTOUTn_MASK register
- use dedicated watchdog timer on A38X instead of second timer
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4423
New driver registers RTC as system clock. New RTC resolution is 1 sec.
Settime and gettime functions were implemented.
Reviewed by: andrew, ian
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Jan Dabros <jsd@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4421
mv_pci driver omitted slot 0, which can be valid device on Armada38x.
New mechanism detects if device is root link, basing on vendor's
and device's IDs.
It is restricted to Armada38x; on other machines, behaviour remains
the same.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4377
Add conditions corresponding to Armada38x-based SoCs,
enhancing their remap capabilities.
This is required for PCIe to work properly.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4376
Add gic_decode_fdt function to fdt_pic_table, allowing to recognize GIC
interrupts on Armada38x. SOC_MV_ARMADA38X ifdef is required because A38X
is the only Marvell's platform in FreeBSD using GIC; lack of ifdef would
lead to linking errors on other platforms.
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4214
Strict compatibility requirement is a root of problems when simplebus'
node has two compatibility strings (i.e. on Armada38x). Removing this
requirement should not interfere with other platforms.
fdt_is_compatible_strict() and fdt_find_compatible() calls were changed
in fdt_common.c and mv_common.c.
Reviewed by: ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4602
This commit introduces initial support for Marvell Armada38x platform.
Changes:
- Add common DTS files for Armada38x SoCs and DTS file for A388-GP
- Add ARMADA38X kernel configuration
- Add option SOC_MV_ARMADA38X and set MV_PCI_PORTS
- Add list of files to compile
- Implement get_tclk(), get_sar_value(), cpu_reset() functions
- Add CPU ID and SoC numbers
- Correct ifdefs in arm/mv/timer.c
Reviewed by: ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4210
Including arm/mv/gpio.c now depends on 'gpio' device. 'device gpio' was
added to all kernconf files of Marvell boards, except ARMADAXP (dummy
mv_gpio_res definition was removed) and ARMADA38X (not supported yet).
This commit allows to use generic files.mv on A38X.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4372
match the physical load address. Remove the *PHYSADDR symbols which are no
longer necessary.
Also remove a bunch of comments, most of which which have been wrong for
quite some time now, and the rest of which are mooted by these changes. All
that's left in this file is assigning a single symbol to its cannonical
value, not much to comment on anymore.
variable during mp_start() which is too late. Move this to mp_setmaxid()
where other architectures set it and move x86 assertions to MI code.
Reviewed by: kib (x86 part)
value is defined as a config option the definition is emitted into
opt_global.h which is force-included into everything. In addition, the
symbol is emitted by the genassym mechanism, but that by its nature reduces
the value to a 0xnnnnnnnn number. When compiling a .S file you end up
with two different definitions of the macro (they evaluate to the same
number, but the text is different, upsetting the compiler).
Nothing has changed about this code for a while but the compile error is
new, so this must be fallout from the clang 3.7 update or something.
missed. In other words, if a new request for an IPI is sent while the
previous request is being handled but the IPI is not cleared yet, the
clearing of the previous IPI request also clears the new one and the
handling is missed.
There are only three MP interrupt controllers in ARM now. Two of them are
fixed by this change, the third one is correct, probably only just by
accident. The fix is minimalistic as new interrupt framework is awaited.
It was debugged on RPi2 where missing IPI handling together with SCHED_ULE
led to situation in which tdq_ipipending was not cleared and so IPI_PREEMPT
was stopped to be sent. Various odditys were found related to slow system
response time like various events timed out, and slow console response.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
Reviewed by: loos, kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D3722
the startup trampoline code. The old code allocated a kva page, mapped it
using using pmap_kenter_nocache(), then freed the kva without destroying
the mapping. This is the only use of pmap_kenter_nocache() in the system,
so redoing this one use of allows it to be garbage collected in the
near future.
SoC's registers base address may differ between boards
(0xf1000000 or 0xd0000000). Therefore, in order to use
the proper CPU Boot Address Redirect register during SMP
initialization in mptramp the real, physical address has
to be passed to mptramp based on the value from DT.
Reviewed by: gber
During Armada's platform_mp_start_ap(), mptramp code
is being copied to the specific physical location (0xffff0000).
Before r265694 the address to which the code should be copied
was equal to the address of mpentry routine that followed the
mptramp in locore.S. Now the mptramp end address should be
exported and used as a copy limit.
Reviewed by: gber
platform code, it is expected these will be merged in the future when the
ARM code is more complete.
Until more boards can be tested only use this with the Raspberry Pi and
rrename the functions on the other SoCs.
Reviewed by: ian@
On armv4 these are defined as synonyms right now, but it's a bit ambiguous
what NOCACHE means (is buffering/write-combining also enabled or not?); this
is a first step towards replacing PTE_NOCACHE with a less ambiguous name.
and the functionality it provided into arm/exception.S. Rename the main
irq handling routine from arm_handler_execute() to arm_irq_handler() to
make it more congruent with how other exception handlers are named, and
also update its signature to reflect what has long been reality: it is
passed just a trapframe pointer, no interrupt number argument.
appropriate for each of the 'foo' in the tree. This will allow us to
compile them together (although symbol conflicts prevent us from doing
that today, this just fixes the file name collision).
implementation in arm/machdep.c. Most arm platforms either don't need to
do anything, or just need to call the standard eventtimer init routines.
A generic implementation that does that is now provided via weak linkage.
Any platform that needs to do something different can provide a its own
implementation to override the generic one.
it into a bunch of different .c files. Remove declarations for the unused
mptramp() function from everywhere except AramadaXP (and I think it's
really not used there either, because the code that references it appears
to be insanely does-nothing in nature).
a sub-node of nexus (ofwbus) rather than direct attach under nexus. This
fixes FDT on x86 and will make coexistence with ACPI on ARM systems easier.
SPARC is unchanged.
Reviewed by: imp, ian
to check the status property in their probe routines.
Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.
Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.
strings and include arbitrary information (IRQ line/domain/sense). When the
ofw_bus_map_intr() API was introduced, it assumed that, as on most systems,
these were either 1 cell, containing an interrupt line, or 2, containing
a line number plus a sense code. It turns out a non-negligible number of
ARM systems use 3 (or even 4!) cells for interrupts, so make this more
general.
related to setting up static device mappings. Since it was only used by
arm/mv/mv_pci.c, it's now just static functions within that file, plus
one public function that gets called only from arm/mv/mv_machdep.c.
obsolete. This involves the following pieces:
- Remove it entirely on PowerPC, where it is not used by MD code either
- Remove all references to machine/fdt.h in non-architecture-specific code
(aside from uart_cpu_fdt.c, shared by ARM and MIPS, and so is somewhat
non-arch-specific).
- Fix code relying on header pollution from machine/fdt.h includes
- Legacy fdtbus.c (still used on x86 FDT systems) now passes resource
requests to its parent (nexus). This allows x86 FDT devices to allocate
both memory and IO requests and removes the last notionally MI use of
fdtbus_bs_tag.
- On those architectures that retain a machine/fdt.h, unused bits like
FDT_MAP_IRQ and FDT_INTR_MAX have been removed.
shifts into the sign bit. Instead use (1U << 31) which gets the
expected result.
This fix is not ideal as it assumes a 32 bit int, but does fix the issue
for most cases.
A similar change was made in OpenBSD.
Discussed with: -arch, rdivacky
Reviewed by: cperciva
fdtbus in most cases. This brings ARM and MIPS more in line with existing
Open Firmware platforms like sparc64 and powerpc, as well as preventing
double-enumeration of the OF tree on embedded PowerPC (first through nexus,
then through fdtbus).
This change is also designed to simplify resource management on FDT platforms
by letting there exist a platform-defined root bus resource_activate() call
instead of replying on fdtbus to do the right thing through fdt_bs_tag.
The OFW_BUS_MAP_INTR() and OFW_BUS_CONFIG_INTR() kobj methods are also
available to implement for similar purposes.
Discussed on: -arm, -mips
Tested by: zbb, brooks, imp, and others
MFC after: 6 weeks
static device mappings, rather than as the first of the initializations
that a platform can hook into. This allows a platform to allocate KVA
from the top of the address space downwards for things like static device
mapping, and return the final "last usable address" result after that and
other early init work is done.
Because some platforms were doing work in initarm_lastaddr() that needs to
be done early, add a new initarm_early_init() routine and move the early
init code to that routine on those platforms.
Rename platform_devmap_init() to initarm_devmap_init() to match all the
other init routines called from initarm() that are designed to be
implemented by platform code.
Add a comment block that explains when these routines are called and the
type of work expected to be done in each of them.
new devmap.[ch] files. Emphasize the MD nature of these things by using
the prefix arm_devmap_ on the function and type names (already a few of
these things found their way into MI code, hopefully it will be harder to
do by accident in the future).
Loading kernel to 0xf00000 has no practical reason.
Starting it from the u-boot's highest possible end address
(2MB counting from 0x0) makes more sense.
Tested by: kevlo
Depending on u-boot's flavor some boards have their SoC registers
base address configured to 0xD0000000 and other to 0xF1000000.
U-boot is passing currently set value via CP15 register.
In order to create proper mapping for SoC registers and allow further
successful initialization it is necessary to replace fdt_immr_pa with
the real value and eventually fix-up device tree blob.
Tested by: kevlo
The only remaining user was the code that allocates bounce pages for armv4
busdma. It's not clear why bounce pages would need uncached memory, but
if that ever changes, kmem_alloc_attr() would be the way to get it.
really need it. That would be almost everywhere it was included. Add
it in a couple files that really do need it and were previously getting
it by accident via another header.
included by vm/pmap.h, which is a prerequisite for arm/machine/pmap.h
so there's no reason to ever include it directly.
Thanks to alc@ for pointing this out.
the right register for power managment. It
was incorrectly using the clock register
which also caused the status to be the
opposite of what it is supposed to be.
1 - its disabled
0 - its enabled
Per kirkwood spec FSS_88F6180_9x_6281_OpenSource.pdf
