After removal of SMB_TRANS some information in the description of
SMB_BWRITE has become stale. E.g., the maximum block size has been
restored to 32.
Also, the descriptions of SMB_BREAD and SMB_BWRITE had some
incorrect information on the SMBus protocol details.
MFC after: 1 week
X-MFC with: r308242
Differential Revision: https://reviews.freebsd.org/D8431
This change reverts most of r281985.
The method did not map to anything defined by SMBus protocol and could
not be implemented for SMBus controllers.
This change is obviously not backwards compatible, but I have good
reasons to believe that there have never been any users of SMB_TRANS.
Discussed with: grembo, jhb
MFC after: 6 weeks
Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
The driver currently supports chips that are fully compliant with the
JEDEC SPD / EEPROM / TS standard (JEDEC Standard 21-C,
TSE2002 Specification, frequenlty referred to as JEDEC JC 42.4).
Additionally some chips from STMicroelectronics are supported as well.
They are compliant except for their Device ID pattern.
Given the continued lack of any common sensor infrastructure, the driver
uses an ad-hoc sysctl to report the temperature.
Reviewed by: wblock (documentation)
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8174
These two ALU instructions first appeared on Linux. Then, libpcap adopted
and made them available since 1.6.2. Now more platforms including NetBSD
have them in kernel. So do we.
--이 줄 이하는 자동으로 제거됩니다--
> Description of fields to fill in above: 76 columns --|
> PR: If and which Problem Report is related.
> Submitted by: If someone else sent in the change.
> Reported by: If someone else reported the issue.
> Reviewed by: If someone else reviewed your modification.
> Approved by: If you needed approval for this commit.
> Obtained from: If the change is from a third party.
> MFC after: N [day[s]|week[s]|month[s]]. Request a reminder email.
> MFH: Ports tree branch name. Request approval for merge.
> Relnotes: Set to 'yes' for mention in release notes.
> Security: Vulnerability reference (one per line) or description.
> Sponsored by: If the change was sponsored by an organization.
> Differential Revision: https://reviews.freebsd.org/D### (*full* phabric URL needed).
> Empty fields above will be automatically removed.
M share/man/man4/bpf.4
M sys/amd64/amd64/bpf_jit_machdep.c
M sys/amd64/amd64/bpf_jit_machdep.h
M sys/i386/i386/bpf_jit_machdep.c
M sys/i386/i386/bpf_jit_machdep.h
M sys/net/bpf_filter.c
VFP code to store the old context, with lazy loading of the new context
when needed.
FPU_KERN_NOCTX is missing as this is unused in the crypto code this has
been tested with, and I am unsure on the requirements of the UEFI
Runtime Services.
Reviewed by: kib
Obtained from: ABT Systeems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8276
All devices:
- add support for rate adaptation via ieee80211_amrr(9);
- use short preamble for transmitted frames when needed;
- multi-bss support:
* for RTL8821AU: 2 VAPs at the same time;
* other: 1 any VAP + 1 sta VAP.
RTL8188CE:
- fix IQ calibration bug (reason of significant speed degradation);
- add h/w crypto acceleration support.
USB:
- A-MPDU Tx support;
- short GI support;
Other:
- add support for RTL8812AU / RTL8821AU chipsets
(a/b/g/n only; no ac yet);
- split merged code into subparts:
* bus glue (usb/*, pci/*, rtl*/usb/*, rtl*/pci/*)
* common (if_rtwn*)
* chip-specific (rtl*/*)
- various other bugfixes.
Due to code reorganization, module names / requirements were changed too:
urtwn urtwnfw -> rtwn rtwn_usb rtwnfw
rtwn rtwnfw -> rtwn rtwn_pci rtwnfw
Tested with RTL8188CE, RTL8188CUS, RTL8188EU and RTL8821AU.
Tested by: kevlo, garga,
Peter Garshtja <peter.garshtja@ambient-md.com>,
Kevin McAleavey <kevin.mcaleavey@knosproject.com>,
Ilias-Dimitrios Vrachnis <id@vrachnis.com>,
<otacilio.neto@bsd.com.br>
Relnotes: yes
This commit, long overdue, contains contributions in the last 2 years
from Stefano Garzarella, Giuseppe Lettieri, Vincenzo Maffione, including:
+ fixes on monitor ports
+ the 'ptnet' virtual device driver, and ptnetmap backend, for
high speed virtual passthrough on VMs (bhyve fixes in an upcoming commit)
+ improved emulated netmap mode
+ more robust error handling
+ removal of stale code
+ various fixes to code and documentation (some mixup between RX and TX
parameters, and private and public variables)
We also include an additional tool, nmreplay, which is functionally
equivalent to tcpreplay but operating on netmap ports.
Ignore the ECN bits on 'tos' and 'set-tos' and allow to use
DCSP names instead of having to embed their TOS equivalents
as plain numbers.
Obtained from: OpenBSD
Sponsored by: OPNsense
Differential Revision: https://reviews.freebsd.org/D8165
- Add m_getclr(9) symlink to ObsoleteFiles.inc (removed in r295481).
- Add const qualifiers in m_dup(), m_dup_pkthdr() and m_tag_copy_chain()
(r286450).
- Fix m_dup_pkthdr() definition (it's not the same as m_move_pkthdr()).
MFC after: 5 days
The tag fastroute came from ipf and was removed in OpenBSD in 2011. The code
allows to skip the in pfil hooks and completely removes the out pfil invoke,
albeit looking up a route that the IP stack will likely find on its own.
The code between IPv4 and IPv6 is also inconsistent and marked as "XXX"
for years.
Submitted by: Franco Fichtner <franco@opnsense.org>
Differential Revision: https://reviews.freebsd.org/D8058
like other PCI network drivers. The sys/ofed directory is now mainly
reserved for generic infiniband code, with exception of the mthca driver.
- Add new manual page, mlx4en(4), describing how to configure and load
mlx4en.
- All relevant driver C-files are now prefixed mlx4, mlx4_en and
mlx4_ib respectivly to avoid object filename collisions when compiling
the kernel. This also fixes an issue with proper dependency file
generation for the C-files in question.
- Device mlxen is now device mlx4en and depends on device mlx4, see
mlx4en(4). Only the network device name remains unchanged.
- The mlx4 and mlx4en modules are now built by default on i386 and
amd64 targets. Only building the mlx4ib module depends on
WITH_OFED=YES .
Sponsored by: Mellanox Technologies
function from restarting the timer.
Commonly taskqueue_enqueue_timeout() is called from within the task
function itself without any checks for teardown. Then it can happen
the timer stays active after the return of taskqueue_drain_timeout(),
because the timeout and task is drained separately.
This patch factors out the teardown flag into the timeout task itself,
allowing existing code to stay as-is instead of applying a teardown
flag to each and every of the timeout task consumers.
Add assert to taskqueue_drain_timeout() which prevents parallel
execution on the same timeout task.
Update manual page documenting the return value of
taskqueue_enqueue_timeout().
Differential Revision: https://reviews.freebsd.org/D8012
Reviewed by: kib, trasz
MFC after: 1 week
db_segsize().
Use db_segsize() to set the default operand/address size for
disassembling. Allow overriding this with the "alternate" display
format /I. The API of db_disasm() should be debooleanized to pass a
more general request (amd64 needs overrides to sizes of 16, 32, and
64, but this commit doesn't implement anything for amd64 since much
larger changes are needed to restore the amd64 disassmbler's support
for non-default sizes).
Fix db_print_loc_and_inst() to ask for the normal format and not the
alternate in normal operation.
This is most useful for vm86 mode, but also works for 16-bit protected
mode.
Use db_segsize() to avoid trying to print a garbage stack trace if %cs
is 16 bits. Print something like the stack trace termination message
for a trap boundary instead.
Document that the alternate format is now useful on i386.
AMD chipsets have proprietary mechanisms for dicovering resources.
Those resources are not discoverable via plug-and-play mechanisms
like PCI configuration registers or ACPI.
For this reason a chipset-specific knowledge of proprietary registers
is required.
At present there are two FreeBSD drivers that require the proprietary
resource discovery. One is amdsbwd which is a driver for the watchdog
timer in the AMD chipsets. The other is intpm SMBus driver when it
attaches to the newer AMD chipsets where the resources of the SMBus HBA
are not described in the regular PCI way.
In both cases the resources are discovered by accessing AMD PMIO space.
Thus, many definitions are shared between the two drivers.
This change puts those defintions into a common header file.
As an added benefit, intpm driver now supports newest FCHs built into
AMD processors of Family 15h, models 70h-7Fh and Family 16h, models
30h-3Fh.
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8004
Now that all of the necessary bits for ARMv6 support for CloudABI have
been checked in, let's hook the kernel module up to the build and
document its existence.
This is an RTL8168 chip, which we already support so all we have to do is add
the vendor ID.
PR: 212876
Submitted by: Tobias Kortkamp <t@tobik.me>
MFC after: 3 days
In preparation for the removal of GNU rcs from base, remove the backup_uses_rcs
functionality from the rc.subr backup_file feature. This functionnality was off
by default
Reviewed by: wblock
Differential Revision: https://reviews.freebsd.org/D7883
In particular, reset the DF_QUIET flag when detaching from a device so
that a driver that marks a device quiet doesn't dictate policy for a
different driver that may claim the device in the future.
Reviewed by: rpokala, wblock
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7803
The flag specifies that the block which uses FPU must be executed in
critical section, i.e. take no context switches, and does not need an
FPU save area during the execution.
It is intended to be applied around fast and short code pathes where
save area allocation is impossible or undesirable, due to context or
due to the relative cost of calculation vs. allocation.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
it. This arg is most interesting for the 'break' command where it
never worked, and for the step command where it is powerful but too
fragile to use much.
Give the full syntax of the 'addr' arg for these commands and some
others. Rename it from 'address' for the generic command.
Fix description of how 'count' is supposed to work for the 'break'
command.
Don't (mis)describe the syntax of the comma for the 'step' command.
Expand the description for the generic command.
Give the full syntax for the 'examine' command. It was also missing
the possible values for the modifier.
Fix mdoc syntax error for the 'search' command.
Remove FUD about consequences of not having a trap handler for the
'search' command.
Split the QUEUE_MACRO_DEBUG into QUEUE_MACRO_DEBUG_TRACE and
QUEUE_MACRO_DEBUG_TRASH.
Add the debug macrso QMD_IS_TRASHED() and QMD_SLIST_CHECK_PREVPTR().
Document these in queue.3.
Reviewed by: emaste
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D3984
Describe PCI-related kernel options for HotPlug and SR-IOV support in the
pci(4) manual page. While here, add a section describing the various
tunables supported by the PCI bus driver as well.
Reviewed by: wblock
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D7754
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Reviewed by: np
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7599
Add routines to trigger a function level reset (FLR) of a PCI-express
device via the PCI-express device control register. This also includes
support routines to wait for pending transactions to complete as well
as calculating the maximum completion timeout permitted by a device.
Change the ppt(4) driver to reset pass through devices before attaching
to a VM during startup and before detaching from a VM during shutdown.
Reviewed by: imp, wblock (earlier version)
MFC after: 1 month
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7751
When the I/O MMU is active in bhyve, all PCI devices need valid entries
in the DMAR context tables. The I/O MMU code does a single enumeration
of the available PCI devices during initialization to add all existing
devices to a domain representing the host. The ppt(4) driver then moves
pass through devices in and out of domains for virtual machines as needed.
However, when new PCI devices were added at runtime either via SR-IOV or
HotPlug, the I/O MMU tables were not updated.
This change adds a new set of EVENTHANDLERS that are invoked when PCI
devices are added and deleted. The I/O MMU driver in bhyve installs
handlers for these events which it uses to add and remove devices to
the "host" domain.
Reviewed by: imp
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7667
Idle page zeroing has been disabled by default on all architectures since
r170816 and has some bugs that make it seemingly unusable. Specifically,
the idle-priority pagezero thread exacerbates contention for the free page
lock, and yields the CPU without releasing it in non-preemptive kernels. The
pagezero thread also does not behave correctly when superpage reservations
are enabled: its target is a function of v_free_count, which includes
reserved-but-free pages, but it is only able to zero pages belonging to the
physical memory allocator.
Reviewed by: alc, imp, kib
Differential Revision: https://reviews.freebsd.org/D7714
This driver only supports 10Mb Ethernet using PIO (the hardware supports
DMA, but the driver only does PIO). There are not any PCCard adapters
supported by this driver, only ISA cards. In addition, it does not use
bus_space but instead uses bcopy with volatile pointers triggering a
host of warnings. (if_ie.c is one of 3 files always built with
-Wno-error)
Relnotes: yes
This hardware is not present on any modern systems. The driver is quite
hackish (raw inb/outb instead of bus_space, and raw inb/outb to random
I/O ports to enable ACPI since it predated proper ACPI support).
Relnotes: yes
The wl(4) driver supports pre-802.11 PCCard wireless adapters that
are slower than 802.11b. They do not work with any of the 802.11
framework and the driver hasn't been reported to actually work in a
long time.
Relnotes: yes
The si(4) driver supported multiport serial adapters for ISA, EISA, and
PCI buses. This driver does not use bus_space, instead it depends on
direct use of the pointer returned by rman_get_virtual(). It is also
still locked by Giant and calls for patch testing to convert it to use
bus_space were unanswered.
Relnotes: yes
queue.h header file and in the queue.3 manual page that they are O(n)
so should be used only in low-usage paths with short lists (otherwise
an STAILQ or TAILQ should be used).
Reviewed by: kib
alternate TCP stack in other then the closed state (pre-listen/connect).
The idea is that *if* that is supported by the alternate stack, it
is asked if its ok to switch. If it approves the "handoff" then we
allow the switch to happen. Also the fini() function now gets a flag
to tell if you are switching away *or* the tcb is destroyed. The
init() call into the alternate stack is moved to the end so the
tcb is more fully formed before the init transpires.
Sponsored by: Netflix Inc.
Differential Revision: D6790
This is a driver for a pre-ATAPI ISA CD-ROM adapter. As noted in
the manpage, this driver is only useful as a backend to cdcontrol to
play audio CDs since it doesn't use DMA, so its data performance is
"abysmal" (and that was true in the mid 90's).
Previously the loop in PCIIOCGETCONF would terminate as soon as it
found enough matches. Now it will continue iterating through the
PCI device list and only terminate if it finds another matching device
for which it has no room to store a conf structure. This means that
PCI_GETCONF_LAST_DEVICE is reliably returned when the number of
matching devices is equal to the number of slots in the matches
buffer. For example, if a program requests the conf structure for a
single PCI function with a specified domain/bus/slot/function it will
now get PCI_GETCONF_LAST_DEVICE instead of PCI_GETCONF_MORE_DEVS.
While here, simplify the loop conditional a bit more by explicitly
breaking out of the loop if copyout() fails and removing a redundant
i < pci_numdevs check.
Reviewed by: vangyzen, imp
MFC after: 1 month
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7445
The PCI_IOV option creates character devices in /dev/iov for each PF
device driver that registers support for creating VFs. By default the
character device is named after the PF device (e.g. /dev/iov/foo0).
This change adds a variant of pci_iov_attach() called pci_iov_attach_name()
that allows the name of the /dev/iov entry to be specified by the
driver.
Reviewed by: rstone
MFC after: 1 month
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7400
New design allows to attach multiple consumers to ntb_transport(4) instance.
Previous design obtained from Linux theoretically allowed that, but was not
practically usable (Linux also has only one consumer driver now).
New design allows hardware resources to be split between several consumers.
For example, one BAR can be dedicated for remote memory access, while other
resources can be used for packet transport for virtual Ethernet interface.
And even without resource split, this code allows to specify which consumer
driver should attach the hardware.
From some points this makes the code even closer to Linux one, even though
Linux does not provide the described flexibility.
callout_when(9). See the man page update for the description of the
intended use.
Tested by: pho
Reviewed by: jhb, bjk (man page updates)
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
X-Differential revision: https://reviews.freebsd.org/D7137
- Support for the AC3165 and AC8260 chipsets was added by r303322 and r303327.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7322
f/w for the other devices supported by this driver.
Patch linked in https://reviews.freebsd.org/D6967 but not actually
a part of the review.
Obtained from DragonflyBSD.
Submitted by: Kevin Bowling <kev009@kev009.com>
MFC after: 2 weeks
Relnotes: yes
The asynchronous I/O changes made previously result in different
behavior out of the box. Previously all AIO requests failed with
ENOSYS / SIGSYS unless aio.ko was explicitly loaded. Now, some AIO
requests complete and others ("unsafe" requests) fail with EOPNOTSUPP.
Reword the introductory paragraph in aio(4) to add a general
description of AIO before describing the vfs.aio.enable_unsafe sysctl.
Remove the ENOSYS error description from aio_fsync(2), aio_read(2),
and aio_write(2) and replace it with a description of EOPNOTSUPP.
Remove the ENOSYS error description from aio_mlock(2).
Log a message to the system log the first time a process requests an
"unsafe" AIO request that fails with EOPNOTSUPP. This is modeled on
the log message used for processes using the legacy pty devices.
Reviewed by: kib (earlier version)
MFC after: 1 week
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7151
