This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.
This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.
MFC after: 1 week
be able to claim I know how the UART code works."
* Just return 115200 as the current baud rate. I should cache it in the
device struct and return that but I'm lazy right now.
* don't error out on other ioctl settings for now, just silently ignore them.
* remove some code that was copied from the 8250 driver that isn't needed
any longer.
Tested:
* AR9331, Carambola-2 board.
console, it calls the grab functions. These functions should turn off
the RX interrupts, and any others that interfere. This makes mountroot
prompt work again. If there's more generalized need other than
prompting, many of these routines should be expanded to do those new
things.
Reviewed by: bde (with reservations)
* Enable RX and host interrupts during bus probe/attach
* Disable all interrupts (+ host ISR) during bus detach
* Enable TX DONE interrupt only when we start transmitting; clear it when
we're done.
* The RX/TX FIFO depth is still conjecture on my part. I'll fix this
shortly.
* The TX FIFO interrupt isn't an "empty" interrupt, it's an "almost empty"
interrupt. Sigh. So..
* .. in ar933x_bus_transmit(), wait for the FIFO to drain before
continuing.
I dislike having to wait for the FIFO to drain, alas.
Tested:
* Atheros AP121 board, AR9331 SoC.
TODO:
* RX/TX overflow, RX error, BREAK support, etc.
* Figure out the true RX/TX FIFO depth.
This implements the bus transmit/receive/sigchg/ipend methods with
a polled interrupt handler (ipend) rather than enabling hardware
interrupts.
The FIFO is faked at 16 bytes deep for now, just so the transmit
IO side doesn't suck too bad (the callout frequency limits how quickly
IO is flushed to the sender, rather than scheduling the callout more
frequently whilst there's active TX. But I digress.)
Tested:
* Atheros AP121 (AR9330) reference board, booting to multi-user interactive
mode.
* Add baud rate and divisor programming code. See below for more
information.
* Flesh out ar933x_init() to disable interrupts and program the initial
console setup.
* Remove #if 0'ed code from ar933x_term().
* Explain what these functions do.
Now, the baud rate and divisor code comes from Linux, as a submission
to the OpenWRT project and Linux kernel from
Gabor Juhos <juhosg@openwrt.org>.
The original ticket for this code is https://dev.openwrt.org/ticket/12031 .
I've contacted Gabor and asked for his permission to also licence the patch
in question (which covers this code) to BSD lience and he's agreed.
Hence why I'm including it here in FreeBSD.
Tested:
* AP121 (AR9330)
* Default clock is 25MHz;
* Remove the UART register macro here - it's not needed as we don't need
to "adjust" the register offset / spacing at all;
* Remove unused fields in the softc.
Tested:
* AP121
This implements the kernel glue needed (getc, putc, rxready).
This isn't a 16550 UART, even if the datasheet overview claims so.
The Linux ar933x support was used as a reference, however the uart code
is a reimplementation.
Attentive viewers will note that the uart code is based off of the ns8250
code and the UART bus code is a stubbed-out version of this. I'll be
replacing it with non-stubbed versions soon, making this a fully featured
driver.
Tested:
* AP121 reference board (AR933x), booting through the mountroot> prompt;
then doing some basic interactive tests in ddb.
