the second-last 64k seems to be the default firmware board configuration
area.
Since I have no idea whether uboot uses it or not - and it's prefixed
with an atheros eeprom signature (0xaa55), I figure the safest thing
to do is mark it as read-only.
I've modified my local tplink firmware building program to generate
a board configuration section - which is separate to this partition.
It's located in the 64k _before_ this particular 64k.
The firmware build program from OpenWRT never initialises those
values and the firmware images from tplink also leave it 0x0, so I
don't currently know what the exact, correct details should be.
the ar71xx platform code should assume a uboot or redboot environment.
The current code gets very confused (and just crashes) on a uboot
environment, where each attribute=value pair is in a single entry.
Redboot on the other hand stores it as "attribute", "value", "attribute",
"value", ...
This allows the kernel to boot on a TP-LINK TL-WR1043ND from flash,
where the uboot environment gets setup. This didn't show up during a netboot
as "tftpboot" and "go" don't setup the uboot environment variables.
The default flash layout gives only 1 megabyte for the kernel, gzipped.
The uboot firmware running on this device only supports gzip, not lzma, so
we actually _do_ have to try and slim the kernel down a bit.
But, since I can't actually do that at the present, I'm opting to:
* extend the kernel from 1mb to 2mb;
* have rootfs fill the rest of that, save 64k;
* eventually I'll hide a 64k config partition at the end, between the
end of rootfs and the ART (radio configuration data.)
The uboot firmware doesn't care about the partition layout. It just
expects the kernel application image to sit at 0xbf020000 (right after
the 128k uboot image.) The uboot header isn't actually read either -
it's "faked" from a "tplink" flash image header. So as long as the
map configuration here matches what is being written out via the
tplink firmware generator, everything is a-ok.
A previous commit disabled compiling the AR9130 support in the default
HAL build in the kernel. Since the AR9130 support won't actually function
without AH_SUPPORT_AR9130 (and that abomination needs to be undone at some
point, in order to allow USB 11n NICs to also work), we now have to
explicitly compile it in.
But since the 11n RF backends don't (currently) join the RF linker set,
one has to compile in _an_ RF backend for the HAL to compile.
At some point it would be nice to correctly update the bus glue to make
this "correct", including having the DDR flush occur in the right spot
(ie, any AHB interrupt.)
put into suspend/shutdown. Old PCI controllers performed that
operation in firmware but for RTL8111C or newer controllers, it's
responsibility of driver. It's not clear whether the firmware of
RTL8111B still downgrades its speed to 10/100Mbps so leave it as it
was.
issues probably needing workarounds in bge(4) when brgphy(4) handles this
PHY. Letting ukphy(4) handle it instead results in a working configuration,
although likely with performance penalties.
The calibrate callout is done with the sc lock held.
This only showed up when using an older NIC (AR5212) whose
radio/phy requires the rfgain adjustment.
Pointy-hat-to: adrian
Sponsored by: Hobnob, Inc.
* Failall is now named just that.
* Add TX ok and TX fail, for aggregate frame sub-frames.
This will break athstats; a followup commit wil resolve this.
Sponsored by: Hobnob, Inc.
Because there is no reliable way to know whether RX MAC is in
stopped state, rejecting all frames would be the only way to
minimize possible races.
Otherwise it's possible to receive frames while stop command
execution is in progress and controller can DMA the frame to freed
RX buffer during that period.
This was observed on recent PCIe controllers(i.e. RTL8111F).
While this change may not be required on old controllers it
wouldn't make negative effects on old controllers. One side effect
of this change is disabling receive so driver reprograms RL_RXCFG
to receive WOL frames when it is put into suspend or shutdown.
This should address occasional 'memory modified free' errors seen
on recent RealTek controllers.
driver would ignore the first link state update if controller
already established a link such that it would have to take
additional link state handling in re_tick().
access.
While I'm here, enable WOL through magic packet but disable waking
up system via unicast, multicast and broadcast frames. Otherwise,
multicast or unicast frame(e.g. ICMP echo request) can wake up
system which is not probably wanted behavior on most environments.
This was not known as problem because RL_CFG5 register access had
not effect until this change.
The capability to wake up system with unicast/multicast frames
are still set in driver, default off, so users who need that
feature can still activate it with ifconfig(8).
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
bit should not affect link establishment process of auto-negotiation
if manual configuration is not used, which is true in auto-negotiation.
However it seems setting this bit interfere with IP1001 PHY's
down-shifting feature such that establishing a 10/100Mbps link failed
when 1000baseT link is not available during auto-negotiation process.
Tested by: Andrey Smagin <samspeed <> mail dot ru >
